To match the definition of GENERATE_PACK_DFU, so a board can customise the
location/name of this file if needed.
Signed-off-by: Damien George <damien@micropython.org>
To have at least one board configured with MBOOT_ENABLE_PACKING, for CI
testing purposes and demonstration of the feature.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, the final piece of data in a compressed file may have
been lost when decompressing.
Signed-off-by: Damien George <damien@micropython.org>
As reported by @jerryneedell, this change was incorrect; the given
ESPTOOL_FLAGS caused `write_flash` to be repeated twice, which doesn't
work.
Closes#3981.
- prevent touch alarm initialization if not set
- fix wake_alarm is set to touch alarm on autoreload
- add ability to have multiple touch alarms in light sleep
Some ports need an extra operation to ensure that the main task is
awoken so that a queued background task will execute during an ongoing
light sleep.
This removes the need to enable supervisor ticks while I2SOut is operating.
Closes: #3952
Originally, I believed the implementation might be shared with AudioOut,
as on the ESP32 (non-S2) the I2S peripheral was also used to drive the DAC.
However, this is not the case on ESP32-S2 and appears it will not be
the case with the ESP32-S3 or -C3, to the extent that there's skeletal
support for either of them in esp-idf master branch.
However, it could still be shared by I2SIn or PDMIn (the latter being
hypothetically implemented as I2SIn + digital postprocessing like we did
in the atmel-sam port, to my understanding), so I moved it to
the common-hal folder.
.. otherwise, the background callback to load the I2S fifos does not get
run. (I'm not sure this is _correct_ behavior of sleep + background
tasks, but it is the current behavior)
There were _possibly_ problems where this routine was being entered
by direct call AND by background callback. Schedule the work here,
and it will be done almost immediately, without worry about interference.
I don't know if this is strictly necessary, but it doesn't hurt. Since
the I2S clock is being run all the time, we have to enter the background
task to fill the FIFO with zeros constantly anyway.
This can be useful so that e.g., on a Kaluga when programming via
the FTDI chip, you can override the variable to specify "--after=hard_reset"
to automatically return to running CircuitPython, choose a different
baud rate (921600 is about 2s faster than 460800), etc:
make BOARD=espressif_kaluga_1 ESPTOOL_FLAGS="-b 921600 --before=default_reset --after=hard_reset"
IO13 is for blue LED
IO14 is the correct pin header between IO18 and IO12
The silk is wrong (shows IO13), but hardware is correct as IO14, but IO14 was not included in pins.c
Silk will be updated on next PCB production run
(note that the before and after files both lack trailing newlines; this is
how the esp-idf do)
OPTIMIZATION_DEFAULT is -Og, which enables optimizations that do not
interfere with the debugger:
```
elseif(CONFIG_COMPILER_OPTIMIZATION_DEFAULT)
list(APPEND compile_options "-Og")
```
The XIP SPI flash on Fomu is slow, which results in certain operations
taking a long time. This becomes a problem for time-critical operations
such as USB.
Move various calls into RAM to improve performance.
This includes the call to __modsi3 and __udivsi3 which are used by the
supervisor handler to determine if periodic callbacks need to be run.
This finishes fixing #3841
Signed-off-by: Sean Cross <sean@xobs.io>
During an interrupt handler, interrupts are implicitly disabled. They
will be re-enabled when the interrupt handler returns.
Due to some changes that were made, varous calls will re-enable
interrupts after they're finished. Examples of this include calling
`CALLBACK_CRITICAL_END` and getting the number of ticks with
`port_get_raw_ticks()`.
This patch prevents this from happening by doing two things:
1. Use standard calls in `port_get_raw_ticks()` to disable and re-enable
interrupts, preventing nesting issues, and
2. Increase the nesting count inside `isr()`, reflecting the implicit
call that is made by hardware when an interrupt is handled
This helps to address #3841.
Signed-off-by: Sean Cross <sean@xobs.io>
* Better messaging when code is stopped by an auto-reload.
* Auto-reload works during sleeps on ESP32-S2. Ticks wake up the
main task each time.
* Made internal naming consistent. CamelCase Python names are NOT
separated by an underscore.
Very long ago, this was apparently not supported in esptool yet, at
least when operating over USB CDC. This now works just fine, and
our esp webtool relies on it as well. It makes flashing faster,
too.
Changes are:
- Remove include of stm32's adc.h because it was recently changed and is
no longer compatible with teensy (and not used anyway).
- Remove define of __disable_irq in mpconfigport.h because it was clashing
with an equivalent definition in core/mk20dx128.h.
- Add -Werror to CFLAGS, and change -std=gnu99 to -std=c99.
Signed-off-by: Damien George <damien@micropython.org>
Mboot builds do not use the external SPI flash in caching mode, and
explicitly disabling it saves RAM and a small bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.
Signed-off-by: Damien George <damien@micropython.org>
When littlefs is enabled extended reading must be supported, and using this
function to read the first block for auto-detection is more efficient (a
smaller read) and does not require a cached SPI-flash read.
Signed-off-by: Damien George <damien@micropython.org>
These functions enable SDRAM data retention in stop mode. Example usage,
in mpconfigboard.h:
#define MICROPY_BOARD_ENTER_STOP sdram_enter_low_power();
#define MICROPY_BOARD_LEAVE_STOP sdram_leave_low_power();
Calculate the bit timing from baudrate if provided, allowing sample point
override. This makes it a lot easier to make CAN work between different
MCUs with different clocks, prescalers etc.
Tested on F4, F7 and H7 Y/V variants.
This much buffer space is required for CDC data out endpoints to avoid any
buffer overflows when the USB CDC is saturated with data.
Signed-off-by: Damien George <damien@micropython.org>
This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
The nrf52840-mdk-usb-dongle and pca10050 comes with a pre-flashed
bootloader (OpenBootloader).
This commit updates the boards "mpconfigboard.mk" to use DFU as
default flashing method and set the corresponding BOOTLOADER
settings such that nrf52840_open_bootloader_1.2.x.ld linker
script is used.
The default DFU flashing method can be disabled by issuing "DFU=0"
when invoking make. This will lead to "segger" being used as default
flashing tool. When using "DFU=0", the linker scripts will not
compensate for any MBR and Bootloader region being present, and might
overwrite them if they were present.
The commit also removes the custom linker script specific to
nrf52840-mdk-usb-dongle as it now points to a generic.
Updated nrf52840-mdk-usb-dongle's README.md to be more clear on
how to deploy the built firmware.
The port README.md has also been updated. In the list of target
boards a new column has been added to indicate which bootloader
is present on the target board. And for consistency, changed all
examples in the README.md to use "deploy" instead of "flash".
An additional Makefile parameter NRFUTIL_PORT can be set in order
to define the serial port to used for the DFU (Default: /dev/ttyACM0).
The "nrfutil" that is used as flasher towards OpenBootloader is
available for installation through Python "pip".
In case of SD=s140, SoftDevice ID 0xB6 is passed to nrfutil's package
generation which corresponds to SoftDevice s140 v6.1.1.
Add the option for "mpconfigboard.mk" to define whether the
board hosts a bootloader or not. The BOOTLOADER make variable
must be set to the name of the bootloader.
When the BOOTLOADER name is set it is also required to supply
the BOOTLOADER_VERSION_MAJOR and the BOOTLOADER_VERSION_MINOR
from the "mpconfigboards.mk". These will be used to resolve which
bootloader linker script that should be passed to the linker.
The BOOTLOADER section also supplies the C-compiler with
BOOTLOADER_<bootloader name>=<version major><version minor>
as a compiler define. This is for future use in case a bootloader
needs to do modification to the startup files or similar (like
setting the VTOR specific to a version of a bootloader).
Adding variables that can be set from other linker scripts:
- _bootloader_head_size:
Bootloader flash offset in front of the application.
- _bootloader_tail_size:
Bootloader offset from the tail of the flash.
In case the bootloader is located at the end.
- _bootloader_head_ram_size:
Bootloader RAM usage in front of the application.
Updated calculations of application flash and RAM.
Two issues are tackled:
1. The calculation of the correct length to print is fixed to treat the
precision as a maximum length instead as the exact length.
This is done for both qstr (%q) and for regular str (%s).
2. Fix the incorrect use of mp_printf("%.*s") to mp_print_strn().
Because of the fix of above issue, some testcases that would print
an embedded null-byte (^@ in test-output) would now fail.
The bug here is that "%s" was used to print null-bytes. Instead,
mp_print_strn is used to make sure all bytes are outputted and the
exact length is respected.
Test-cases are added for both %s and %q with a combination of precision
and padding specifiers.
The zephyr function net_shell_cmd_iface() was removed in zephyr v1.14.0,
therefore the MicroPython zephyr port did not build with newer zephyr
versions when CONFIG_NET_SHELL=y. Replace with a more general
shell_exec() function that can execute any zephyr shell command. For
example:
>>> zephyr.shell_exec("net")
Subcommands:
allocs :Print network memory allocations.
arp :Print information about IPv4 ARP cache.
conn :Print information about network connections.
dns :Show how DNS is configured.
events :Monitor network management events.
gptp :Print information about gPTP support.
iface :Print information about network interfaces.
ipv6 :Print information about IPv6 specific information and
configuration.
mem :Print information about network memory usage.
nbr :Print neighbor information.
ping :Ping a network host.
pkt :net_pkt information.
ppp :PPP information.
resume :Resume a network interface
route :Show network route.
stacks :Show network stacks information.
stats :Show network statistics.
suspend :Suspend a network interface
tcp :Connect/send/close TCP connection.
vlan :Show VLAN information.
websocket :Print information about WebSocket connections.
>>> zephyr.shell_exec("kernel")
kernel - Kernel commands
Subcommands:
cycles :Kernel cycles.
reboot :Reboot.
stacks :List threads stack usage.
threads :List kernel threads.
uptime :Kernel uptime.
version :Kernel version.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The -Og optimisation level produces a more realistic build, gives a better
debugging experience, and generates smaller code than -O0, allowing debug
builds to fit in flash.
This commit also assigns variables in can.c to prevent warnings when -Og is
used, and builds a board in CI with DEBUG=1 enabled.
Signed-off-by: Damien George <damien@micropython.org>
Allows reserving CAN, I2C, SPI, Timer and UART peripherals. If reserved
the peripheral cannot be accessed from Python.
Signed-off-by: Damien George <damien@micropython.org>
Even though IRQs are disabled this seems to be required on H7 Rev Y,
otherwise Systick interrupt triggers and the MCU leaves the stop mode
immediately.
This commit saves OSCs/PLLs state before STOP mode and restores them on
exit. Some boards use HSI48 for USB for example, others have PLL2/3
enabled, etc.
* Remove BrokenPipeError and prefer to return the number of bytes
received. (May be zero.)
* Add two minute backup timeout to reduce the chance we hang on
recv accidentally.
This allows calls to `allocate_memory()` while the VM is running, it will then allocate from the GC heap (unless there is a suitable hole among the supervisor allocations), and when the VM exits and the GC heap is freed, the allocation will be moved to the bottom of the former GC heap and transformed into a proper supervisor allocation. Existing movable allocations will also be moved to defragment the supervisor heap and ensure that the next VM run gets as much memory as possible for the GC heap.
By itself this breaks terminalio because it violates the assumption that supervisor_display_move_memory() still has access to an undisturbed heap to copy the tilegrid from. It will work in many cases, but if you're unlucky you will get garbled terminal contents after exiting from the vm run that created the display. This will be fixed in the following commit, which is separate to simplify review.
When a TLS connection is closed by the server it usually sends a
notice. We see this incoming byte with lwip_ioctl and try to read
it. The read returns 0 but we keep trying anyway. Now, we quit
trying when we get zero back. If the connection was still alive
it'd either read a byte or delay until a byte could be read.
`pow(a, b, c)` can compute `(a ** b) % c` efficiently (in time and memory).
This can be useful for extremely specific applications, like implementing
the RSA cryptosystem. For typical uses of CircuitPython, this is not an
important feature. A survey of the bundle and learn system didn't find
any uses.
Disable it on M0 builds so that we can fit in needed upgrades to the USB
stack.
Also known as L2CAP "connection oriented channels". This provides a
socket-like data transfer mechanism for BLE.
Currently only implemented for NimBLE on STM32 / Unix.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
Instead of unrolling the code 16 times, unroll it 4 times and loop
over it 4 times. This gives the same 16 iterations, but at an expense
of less flash space.
This reclaims over 1kB of flash space by simplifying certain exception
messages. e.g., it will no longer display the requested/actual length
when a fixed list/tuple of N items is needed:
if (MICROPY_ERROR_REPORTING == MICROPY_ERROR_REPORTING_TERSE) {
mp_raise_ValueError(translate("tuple/list has wrong length"));
} else {
mp_raise_ValueError_varg(translate("requested length %d but object has length %d"),
(int)len, (int)seq_len);
Other chip families including samd51 keep their current error reporting
capabilities.
This fixes the build for non-STM32WB based boards when the NimBLE submodule
has not been fetched, and also allows STM32WB boards to build with BLE
disabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
While trying to debug #3572, I noticed that I would frequently break in
the midst of gettimeofday and that the routine get_adjusted_boot_time
had to take and release locks. Furthermore, we don't want "adjusted"
boot time, which could go forwards or backwards depending on the
adjustment (such as setting the clock used by gettimeofday() to the network
time)
Before, there were two problems:
* Even if a pulsein was never constructed, supervisor_disable_tick
would occur during restart. This could cancel out a supervisor_enable_tick
from someplace else, with unexpected results.
* If two or more pulseins were constructed, each one would enable ticks,
but only the last one deinited (or the reset routine) would disable,
leaving ticks running indefinitely.
In my testing, it seemed that this led to the board sometimes stopping when
it should have auto-reloaded.
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the STM32WB HCI interface (between the two CPUs) to
require the use of MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS, and as a
consequence to require NimBLE. IPCC RX IRQs now schedule the NimBLE
handler to run via mp_sched_schedule.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This re-points the submodule to my personal fork of esp-idf.
Users may need to `git submodule sync` in their existing trees when
this change occurs.
Adds just the following commit in esp-idf:
> esp_crt_bundle: Allow verify_callback to correct BADCERT_BAD_MD
* No weak link for modules. It only impacts _os and _time and is
already disabled for non-full builds.
* Turn off PA00 and PA01 because they are the crystal on the Metro
M0 Express.
* Change ejected default to false to move it to BSS. It is set on
USB connection anyway.
* Set sinc_filter to const. Doesn't help flash but keeps it out of
RAM.
* Initialize the EPaper display on the MagTag at start.
* Tweak the display send to take a const buffer.
* Correct Luma math
* Multiply the blue component, not add.
* Add all of the components together before dividing. This
reduces the impact of truncated division.
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead. This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.
The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms. When RX IRQ idle events arrive, it will also schedule this
task to improve latency.
There is a similar change for the unix port where the background thread now
queues the scheduled task.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This requires that the event handlers are called from non-interrupt context
(i.e. the MicroPython scheduler).
This will allow the BLE stack (e.g. NimBLE) to run from the scheduler
rather than an IRQ like PENDSV, and therefore be able to invoke Python
callbacks directly/synchronously. This allows writing Python BLE handlers
for events that require immediate response such as _IRQ_READ_REQUEST (which
was previous a hard IRQ) and future events relating to pairing/bonding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Closes#3688
With this change, I don't get the ESP_ERROR_CHECK failed repeatedly
running code that imports wifi. (I'm not getting a successful connection
but that's probably my own fault, such as a secrets problem)
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change machine.mem32['foo'] (or using any other non-integer
subscript) could result in a fault due to 'foo' being interpreted as an
integer. And when writing code it's hard to tell if the fault is due to a
bad subscript type, or an integer subscript that specifies an invalid
memory address.
The type of the object used in the subscript is now tested to be an
integer by using mp_obj_get_int_truncated instead of
mp_obj_int_get_truncated. The performance hit of this change is minimal,
and machine.memX objects are more for convenience than performance (there
are many other ways to read/write memory in a faster way),
Fixes issue #6588.
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.
Signed-off-by: Damien George <damien@micropython.org>
Add working example code to provide a starting point for users with files
that they can just copy, and include the modules in the coverage test to
verify the complete user C module build functionality. The cexample module
uses the code originally found in cmodules.rst, which has been updated to
reflect this and partially rewritten with more complete information.
Support building .cpp files and linking them into the micropython
executable in a way similar to how it is done for .c files. The main
incentive here is to enable user C modules to use C++ files (which are put
in SRC_MOD_CXX by py.mk) since the core itself does not utilize C++.
However, to verify build functionality a unix overage test is added. The
esp32 port already has CXXFLAGS so just add the user modules' flags to it.
For the unix port use a copy of the CFLAGS but strip the ones which are not
usable for C++.
The same seed will only occur if the board is the same, the RTC has the
same time (eg freshly powered up) and the first call to this function (eg
via an "import random") is done at exactly the same time since reset.
Signed-off-by: Damien George <damien@micropython.org>
For seeding, the RNG function of the ESP-IDF is used, which is told to be a
true RNG, at least when WiFi or Bluetooth is enabled. Seeding on import is
as per CPython. To obtain a reproducible sequence of pseudo-random numbers
one must explicitly seed with a known value.
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.
This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised. It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.
Signed-off-by: Damien George <damien@micropython.org>
* explain the introduction of the temporary variable in get_t_config
* get rid of unneeded __attribute__
* get rid of unneeded members of canio_can_obj_t
* get rid of unneeded header inclusion
If the device is not connected over USB CDC to a host then all output to
the CDC (eg initial boot messages) is written to the CDC TX buffer with
wrapping, so that the most recent data is retained when the USB CDC is
eventually connected (eg so the REPL banner is displayed upon connection).
This commit fixes a bug in this behaviour, which was likely introduced in
e4fcd216e0, where the initial data in the CDC
TX buffer is repeated multiple times on first connection of the device to
the host.
Signed-off-by: Damien George <damien@micropython.org>
This is a generally useful feature and because it's part of the object
model it cannot be added at runtime by some loadable Python code, so enable
it on the standard unix build.
This decreases the link time, especially on desktop machines with many CPU
cores. However, it does come at a slight cost in binary size, making the flash
section about 200 bytes bigger for circuitplayground_express.
Before, linking build-circuitplayground_express/firmware.elf takes
8.8s elapsed time, leaving 3128 bytes free in flash.
After, linking build-circuitplayground_express/firmware.elf takes 2.8s elapsed
time, leaving 2924 bytes free in flash. (-6 seconds, -204 bytes free)
If necessary, we can make this per-board or even per-translation to squeeze full
builds.
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).
Signed-off-by: Damien George <damien@micropython.org>
When installing WS firmware, the very first GET_STATE can take several
seconds to respond (especially with the larger binaries like
BLE_stack_full).
Allows stm.rfcore_sys_hci to take an optional timeout, defaulting to
SYS_ACK_TIMEOUT_MS (which is 250ms).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The flash can sometimes be in an already-unlocked state, and attempting to
unlock it again will cause an immediate reset. So make _Flash.unlock()
check FLASH_CR_LOCK to get the current state.
Also fix some magic numbers for FLASH_CR_LOCK AND FLASH_CR_STRT.
The machine.reset() could be removed because it no longer crashes now that
the flash unlock is fixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The time.sleep() and time.monotonic() functions break the timer
interrupt on which PewPew10 display relies, so we can't use them
anymore. Instead I'm adding a time-keeping function to the display
code itself, which then can be used in pew.tick() internally.
The issue was that a time.sleep() would set the RTC wake up
further into the future even if we wanted to tick every ms. Ticking
every ms is used to time the autoreload delay and without it,
autoreload doesn't work.
Fixes#3528
This commit adds a script that can be run on-device to install FUS and WS
binaries from the filesystem. Instructions for use are provided in
the rfcore_firmware.py file.
The commit also removes unneeded functionality from the existing rfcore.py
debug script (and renames it rfcore_debug.py).
The new functions provide FUS/WS status, version and SYS HCI commands:
- stm.rfcore_status()
- stm.rfcore_fw_version(fw_id)
- stm.rfcore_sys_hci(ogf, ocf, cmd)
This unifies the flash config to the settings used by the Boot ROM.
This makes the config unique per board which allows for changing
quad enable and status bit differences per flash device. It also
allows for timing differences due to the board layout.
This change also tweaks linker layout to leave more ram space for
the CircuitPython heap.
The has successfully run my loopback self-test program for CAN,
which tests transmission, reception, and filtering. The 1M baud rate setting
was also verified on saleae to be accurate.
Changes are:
- Fix missing IRQ handler when SDMMC2 is used instead of SDMMC1 with H7
MCUs.
- Removed outdated H7 series compatibility macros.
- Defined common IRQ handler macro for F4 series.
It requires mp_hal_time_ns() to be provided by a port. This function
allows very accurate absolute timestamps.
Enabled on unix, windows, stm32, esp8266 and esp32.
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftSPI constructor is now used soley to create SoftSPI instances, it
can no longer delegate to create a hardware-based SPI instance.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
Zephyr v2.4.0 added a const qualifier to usages of struct device to
allow storing device driver instances exclusively in flash and thereby
reduce ram footprint.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
I have a function where it should be impossible to reach the end, so I put in a safe-mode reset at the bottom:
```
int find_unused_slot(void) {
// precondition: you already verified that a slot was available
for (int i=0; i<NUM_SLOTS; i++) {
if( slot_free(i)) {
return i;
}
}
safe_mode_reset(MICROPY_FATAL_ERROR);
}
```
However, the compiler still gave a diagnostic, because safe_mode_reset was not declared NORETURN.
So I started by teaching the compiler that reset_into_safe_mode never returned. This leads at least one level deeper due to reset_cpu needing to be a NORETURN function. Each port is a little different in this area. I also marked reset_to_bootloader as NORETURN.
Additional notes:
* stm32's reset_to_bootloader was not implemented, but now does a bare reset. Most stm32s are not fitted with uf2 bootloaders anyway.
* ditto cxd56
* esp32s2 did not implement reset_cpu at all. I used esp_restart(). (not tested)
* litex did not implement reset_cpu at all. I used reboot_ctrl_write. But notably this is what reset_to_bootloader already did, so one or the other must be incorrect (not tested). reboot_ctrl_write cannot be declared NORETURN, as it returns unless the special value 0xac is written), so a new unreachable forever-loop is added.
* cxd56's reset is via a boardctl() call which can't generically be declared NORETURN, so a new unreacahble "for(;;)" forever-loop is added.
* In several places, NVIC_SystemReset is redeclared with NORETURN applied. This is accepted just fine by gcc. I chose this as preferable to editing the multiple copies of CMSIS headers where it is normally declared.
* the stub safe_mode reset simply aborts. This is used in mpy-cross.
Make the instructions more complete by documenting all needed steps for
starting from scratch. Also add a section for MSYS2 since the Travis build
uses it as well and it's a good alternative for Cygwin. Remove the mingw32
reference since it's not readily available anymore in most Linux distros
nor compiles successfully.
The device info table has a different layout when core 2 is in FUS mode.
In particular it's larger than the 32 bytes used when in WS mode and if the
correct amount of space is not allocated then the end of the table may be
overwritten with other data (eg with FUS version 0.5.3). So update the
structure to fix this.
Also update rfcore.py to disable IRQs (which are enabled by rfcore.c), to
not depend on uctypes, and to not require the asm_thumb emitter.
Signed-off-by: Damien George <damien@micropython.org>
Lightly tested:
* no matches (catch-all)
* standard address single address matches (even and odd positions)
* standard address mask matches
* only tested that extended doesn't match non-extended
Tested & working:
* Send standard packets
* Receive standard packets (1 FIFO, no filter)
Interoperation between SAM E54 Xplained running this tree and
MicroPython running on STM32F405 Feather with an external
transceiver was also tested.
Many other aspects of a full implementation are not yet present,
such as error detection and recovery.
And enable this feature on unix, the coverage variant. The .exp test file
is needed so the test can run on CPython versions prior to "@=" operator
support.
Signed-off-by: Damien George <damien@micropython.org>
For time-based functions that work with absolute time there is the need for
an Epoch, to set the zero-point at which the absolute time starts counting.
Such functions include time.time() and filesystem stat return values. And
different ports may use a different Epoch.
To make it clearer what functions use the Epoch (whatever it may be), and
make the ports more consistent with their use of the Epoch, this commit
renames all Epoch related functions to include the word "epoch" in their
name (and remove references to "2000").
Along with this rename, the following things have changed:
- mp_hal_time_ns() is now specified to return the number of nanoseconds
since the Epoch, rather than since 1970 (but since this is an internal
function it doesn't change anything for the user).
- littlefs timestamps on the esp8266 have been fixed (they were previously
off by 30 years in nanoseconds).
Otherwise, there is no functional change made by this commit.
Signed-off-by: Damien George <damien@micropython.org>
To portably get the Epoch. This is simply aliased to localtime() on ports
that are not timezone aware.
Signed-off-by: Damien George <damien@micropython.org>
This commit removes release-specific builds for the esp8266 and makes the
normal build of the GENERIC board more like the release build. This makes
esp8266 like all the other ports, for which there is no difference between
a daily build and a release build, making things less confusing.
Release builds were previously defined by UART_OS=-1 (disable OS messages)
and using manifest_release.py to include more frozen modules.
The changes in this commit are:
- Remove manifest_release.py.
- Add existing modules from manifest_release.py (except example code)
to the GENERIC board's manifest.py file.
- Change UART_OS default to -1 to disable OS messages by default.
Signed-off-by: Damien George <damien@micropython.org>
PPP support was disabled in 96008ff59a -
marked as "unsupported" due to an early IDF v4 release. With the currently
supported IDF v4.x version - 4c81978a - it appears to be working just fine.
This commit changes the default logging level on all esp32 boards to ERROR.
The esp32 port is now stable enough that it makes sense to remove the info
logs to make the output cleaner, and to match other ports. More verbose
logging can always be reenabled via esp.osdebug().
This also fixes issue #6354, error messages from NimBLE: the problem is
that ble.active(True) will cause the IDF's NimBLE port to reset the
"NimBLE" tag back to the default level (which was INFO prior to this
commit). Even if the user had previously called esp.osdebug(None), because
the IDF is setting the "NimBLE" tag back to the default (INFO), the
messages will continue to be shown.
The one quirk is that if the user does want to see the additional logging,
then they must call esp.osdebug(0, 3) after ble.active(True) to undo the
IDF setting the level back to the default (now ERROR). This means that
it's impossible (via Python/esp.osdebug) to see stack-startup logging,
you'd have to recompile with the default level changed back to INFO.
Despite the [silk on the dock board](https://wiki.makerdiary.com/nrf52840-m2-devkit/resources/nrf52840_m2_devkit_hw_diagram_v1_0.pdf), the SDA/SCL pins weren't defined. Though, they were already defined in `mpconfigboard.h`.
Same for RX/TX. It looks like it declared `TXD` and `RXD`, so I didn't want to remove those, but I think it makes sense to have the "standard" pin names, but I moved ithem to illustrate they were all referencing the same pins.
I mimicked the whitespace I saw in the metro_nrf52840_express port.
I recently misdiagnosed a "maybe-uninitialized" diagnostic as a bug in
asf4. However, the problem was in our SPI code.
A special case for samr21 MCUs was being applied to same54p20a and possibly
other D5x/E5x MCUs, since the check was simply for pin PC19 existing at all.
Change the check to use the macro PIN_PC19F_SERCOM4_PAD0 which is only
defined if special function F of pin PC19 is SERCOM4 PAD0.
Reorganize the code a little bit so that brace-matching in editors is
not confused by the conditionalized code, including an unrelated change
for APA102_SCK's condition.
Revert the change to the Makefile that incorrectly attempted to silence
the diagnostic.
.. there is an instance of it that looks like a "true positive", but it only
affects sdhc transfers that are not a multiple of 4 bytes, which I don't think
happens. (sd card blocks are always 512 bytes) I can fix this in our
asf4 repo but that would mean this should be deferred until after #3384 is
merged, since that also touches asf4 very invasively by adding a whole new
chip family.
If any diagnostics occur, we will want to either add `/* FALLTHROUGH */`
or `break;` as appropriate. I only tested a few builds (trinket m0
and metro m4 express)
Limor confirmed that the all shipping revisions starting with Rev D had QSPI flash chips installed.
Note that when neither EXTERNAL_FLASH_QSPI_SINGLE nor EXTERNAL_FLASH_QSPI_DUAL is specified quad mode is assumed, so this is addressed by removing the setting altogether.
Support freezing modules via manifest.py for consistency with the other
ports. In essence this comes down to calling makemanifest.py and adding
the resulting .c file to the build. Note the file with preprocessed qstrs
has been renamed to match what makemanifest.py expects and which is also
the name all other ports use.
This fixes SPI with PSRAM allocated buffers. DMA with SPI2 was
attempted but produced junk output. This manual copy is less than
2x slower than DMA when not interrupted.
Fixes#3339
The mpconfigport.h file is an internal header and should only ever be
included once by mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
This allows prototyping rfcore.c improvements from Python.
This was mostly written by @dpgeorge with small modifications to work after
rfcore_init() by @jimmo.
Before this change there was up to a 128ms delay on incoming payloads from
CPU2 as it was polled by SysTick. Now the RX IRQ immediately schedules the
PendSV.
This is required to allow using WS firmware newer than 1.1.1 concurrently
with USB (e.g. USB VCP). It prevents CPU2 from modifying the CLK48 config
on boot.
Tested on WS=1.8 FUS=1.1.
See AN5289 and https://github.com/micropython/micropython/issues/6316
- Split tables and buffers into SRAM2A/2B.
- Use structs rather than word offsets to access tables.
- Use FLASH_IPCCDBA register value rather than option bytes directly.
This allows `ble.active(1)` to fail correctly if the HCI controller is
unavailable.
It also avoids an infine loop in the NimBLE event handler where NimBLE
doesn't correctly detect that the HCI controller is unavailable and keeps
trying to reset.
Furthermore, it fixes an issue where GATT service registrations were left
allocated, which led to a bad realloc if the stack was activated multiple
times.
MicroPython and NimBLE must be on the same core, for synchronisation of the
BLE ringbuf and the MicroPython scheduler. However, in the current IDF
versions (3.3 and 4.0) there are issues (see e.g. #5489) with running
NimBLE on core 1.
This change - pinning both tasks to core 0 - makes it possible to reliably
run the BLE multitests on esp32 boards.
This commit adds support for using Bluetooth on the unix port via a H4
serial interface (distinct from a USB dongle), with both BTstack and NimBLE
Bluetooth stacks.
Note that MICROPY_PY_BLUETOOTH is now disabled for the coverage variant.
Prior to this commit Bluetooth was anyway not being built on Travis because
libusb was not detected. But now that bluetooth works in H4 mode it will
be built, and will lead to a large decrease in coverage because Bluetooth
tests cannot be run on Travis.
Previously the interaction between the different layers of the Bluetooth
stack was different on each port and each stack. This commit defines
common interfaces between them and implements them for cyw43, btstack,
nimble, stm32, unix.
mp_irq_init() is useful when the IRQ object is allocated by the caller.
The mp_irq_methods_t.init method is not used anywhere so has been removed.
Signed-off-by: Damien George <damien@micropython.org>
By setting MICROPY_EPOCH_IS_1970 a port can opt to use 1970/1/1 as the
Epoch for timestamps returned by stat(). And this setting is enabled on
the unix and windows ports because that's what they use.
Signed-off-by: Damien George <damien@micropython.org>
On 32-bit builds these stat fields will overflow a small-int, so use
mp_obj_new_int_from_uint to construct the int object.
Signed-off-by: Damien George <damien@micropython.org>
gettimeofday returns seconds since 2000/1/1 so needs to be adjusted to
seconds since 1970/1/1 to give the correct return value of mp_hal_time_ns.
Signed-off-by: Damien George <damien@micropython.org>
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, if you configure a pin as an output type (I2C in this
example) and then later configure it back as an input, then it will report
the type incorrectly. Example:
>>> import machine
>>> b6 = machine.Pin('B6')
>>> b6
Pin(Pin.cpu.B6, mode=Pin.IN)
>>> machine.I2C(1)
I2C(1, scl=B6, sda=B7, freq=420000)
>>> b6
Pin(Pin.cpu.B6, mode=Pin.ALT_OPEN_DRAIN, pull=Pin.PULL_UP, af=Pin.AF4_I2C1)
>>> b6.init(machine.Pin.IN)
>>> b6
Pin(Pin.cpu.B6, mode=Pin.ALT_OPEN_DRAIN, af=Pin.AF4_I2C1)
With this commit the last print now works:
>>> b6
Pin(Pin.cpu.B6, mode=Pin.IN)
Include storage/flash_map.h unconditionally so we always have access to the
FLASH_AREA_LABEL_EXISTS macro, even if CONFIG_FLASH_MAP is not defined.
This fixes a build error for the qemu_x86 board:
main.c:108:63: error: missing binary operator before token "("
108 | #elif defined(CONFIG_FLASH_MAP) && FLASH_AREA_LABEL_EXISTS(storage)
| ^
../../py/mkrules.mk:88: recipe for target 'build/genhdr/qstr.i.last' failed
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
.. however, the number of endpoints is only set for SAMD (8).
Other ports need to set the value. Otherwise, the build will show
the message
```
Unable to check whether maximum number of endpoints is respected
```
The font is missing many characters and the build needs the space.
We can optimize font storage when we get a good font.
The serial output will work as usual.
this now fits locally (though it's very close to capacity);
let's see what the CI says.
```
make BOARD=metro_m0_express clean && make BOARD=metro_m0_express TRANSLATION=ja
...
253448 bytes used, 248 bytes free in flash firmware space out of 253696 bytes (247.75kB).
```
This was the FS issue I saw when debugging wifi and only happens
when the first write is to sector 0. It causes issues because it
blanks all of sector 0 after the first block.
Fixes#3133
This is a slight trade-off with code size, in places where a "_varg"
mp_raise variant is now used. The net savings on trinket_m0 is
just 32 bytes.
It also means that the translation will include the original English
text, and cannot be translated. These are usually names of Python
types such as int, set, or dict or special values such as "inf" or
"Nan".
.. this probably came from the examples that I studied at the beginning
of implementation.
The card detection feature is unused. As a "detect pin" is not
sent from the shared-bindings, there is no way to get the correct pin
anyway. Instead, if code needs to detect the insertion state it can
directly use the pin as GPIO in Python code.
Currently, only the bus specs of the stm32f405xx have been coded.
Other stm-family chips need (at a minimum) the specs added in their
periph.[ch] files.
Add aliases for SDI, SDO and EN, so that pin names match the text on the
PCB to avoid confusion.
Also disable all pins from port B, because that package of SAMD21
doesn't have port B.
The SCSI driver calls GetCapacity to get the block size and number of
blocks of the underlying block-device/LUN. It caches these values and uses
them later on to verify that reads/writes are within the bounds of the LUN.
But, prior to this commit, there was only one set of cached values for all
LUNs, so the bounds checking for a LUN could use incorrect values, values
from one of the other LUNs that most recently updated the cached values.
This would lead to failed SCSI requests.
This commit fixes this issue by having separate cached values for each LUN.
Signed-off-by: Damien George <damien@micropython.org>
Enabling the following features for all targets, except for nrf51
targets compiled to be used with SoftDevice:
- MICROPY_PY_ARRAY_SLICE_ASSIGN
- MICROPY_PY_SYS_STDFILES
- MICROPY_PY_UBINASCII
Splitting mpconfigport.h into multiple device specific
files in order to facilitate variations between devices.
Due to the fact that the devices might have variations in
features and also variations in flash size it makes sense
that some devices offers more functionality than others
without being limited by restricted devices.
For example more micropython features can be activated for
nrf52840 with 1MB flash, compared to nrf51 with 256KB.
This code is imported from musl, to match existing code in libm_dbl.
The file is also added to the build in stm32/Makefile. It's not needed by
the core code but, similar to c5cc64175b,
allows round() to be used by user C modules or board extensions.
A previous commit 3a9d948032 can cause
lock-ups of the RMT driver, so this commit reverses that, adds a loop_en
flag, and explicitly controls the TX interrupt in write_pulses(). This
provides correct looping, non-blocking writes and sensible behaviour for
wait_done().
See also #6167.
BHB needs better accuracy from the ADC readings. To avoid changing the ADC configuration for all boards or adding complexity to AnalogIn, I implemented a custom user module to allow the BHB to talk to the ADC in the way that it needs to. I'm open to other approaches here, but this seemed like the least invasive and complex option.
The newest version for the Stage library for PewPewM4 no longer contains
embedded graphics, which frees enough space in flash to enabled back
AnalogIO and also add USB_HID. There is still ~192 bytes left free.
If new additions to CircuitPython make it grow further, we can disable
USB_HID again.
We're moving towards a co-processor model and a Wiznet library is
already available.
New native APIs will replace these for chips with networking like the
ESP32S2 but they won't be these.
On my hardware, esptool reports
MAC: 7c:df:a1:02:6c:b8
after this change, the USB descriptor says SerialNumber: 7CDFA1026CB8
and microcontroller.cpu.id has
>>> "".join("%02x" % byte for byte in microcontroller.cpu.uid)
'c7fd1a20c68b'
Note that the nibble-swapping between USB and cpu.uid is typical.
For instance, an stm32 board has USB SerialNumber
24002500F005D42445632302 but hex-converted microcontroller.cpu.id
420052000f504d4254363220.
The motivation for doing this is so that we can allow
common_hal_mcu_disable_interrupts in IRQ context, something that works
on other ports, but not on nRF with SD enabled. This is because
when SD is enabled, calling sd_softdevice_is_enabled in the context
of an interrupt with priority 2 or 3 causes a HardFault. We have chosen
to give the USB interrupt priority 2 on nRF, the highest priority that
is compatible with SD.
Since at least SoftDevice s130 v2.0.1, sd_nvic_critical_region_enter/exit
have been implemented as inline functions and are safe to call even if
softdevice is not enabled. Reference kindly provided by danh:
https://devzone.nordicsemi.com/f/nordic-q-a/29553/sd_nvic_critical_region_enter-exit-missing-in-s130-v2
Switching to these as the default/only way to enable/disable interrupts
simplifies things, and fixes several problems and potential problems:
* Interrupts at priority 2 or 3 could not call common_hal_mcu_disable_interrupts
because the call to sd_softdevice_is_enabled would HardFault
* Hypothetically, the state of sd_softdevice_is_enabled
could change from the disable to the enable call, meaning the calls
would not match (__disable_irq() could be balanced with
sd_nvic_critical_region_exit).
This also fixes a problem I believe would exist if disable() were called
twice when SD is enabled. There is a single "is_nested_critical_region"
flag, and the second call would set it to 1. Both of the enable()
calls that followed would call critical_region_exit(1), and interrupts
would not properly be reenabled. In the new version of the code,
we use our own nesting_count value to track the intended state, so
now nested disable()s only call critical_region_enter() once, only
updating is_nested_critical_region once; and only the second enable()
call will call critical_region_exit, with the right value of i_n_c_r.
Finally, in port_sleep_until_interrupt, if !sd_enabled, we really do
need to __disable_irq, rather than using the common_hal_mcu routines;
the reason why is documented in a comment.
Not all boards have external flash or other components that make them
require 2.7V -- sometimes we can get considerably longer battery life
by decreasing this requirement.
In particular, pewpew10 and pewpew_m4 are powered directly from
battery, with no LDO, and should work fine down to 1.6V.
So that micropython-dev can be used to test VFS code, and inspect and build
filesystem images that are compatible with bare-metal systems.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds time.ticks_ms/us support using RTC1 as the timebase. It
also adds the time.ticks_add/diff helper functions. This feature can be
enabled using MICROPY_PY_TIME_TICKS. If disabled the system uses the
legacy sleep methods and does not have any ticks functions.
In addition support for MICROPY_EVENT_POLL_HOOK was added to the
time.sleep_ms(x) function, making this function more power efficient and
allows support for select.poll/asyncio. To support this, the RTC's CCR0
was used to schedule a ~1msec event to wakeup the CPU.
Some important notes about the RTC timebase:
- Since the granularity of RTC1's ticks are approx 30usec, time.ticks_us is
not perfect, does not have 1us resolution, but is otherwise quite usable.
For tighter measurments the ticker's 1MHz counter should be used.
- time.ticks_ms(x) should *not* be called in an IRQ with higher prio than
the RTC overflow irq (3). If so it introduces a race condition and
possibly leads to wrong tick calculations.
See #6171 and #6202.
I discussed with Hierophect on Discord about how to "de-nest" the code
for configuring SPI objects on STM, because the problems with one
nesting level per pin becomes unmanageable with the up to 10 pins of
SDIO.
This code (which is only compile-tested so far) demonstrates the concept
we discussed.
The SCK pin is always required. Loop over all possibilities of the SCK
pin. When we are considering a particular item in the mcu_spi_sck_list
we have now become committed to using a particular periph_index. If all
the other pins can be satisfied by that periph_index, then we have a
working combination. Once we have a working combination that is not
reserved, we can return that combination. On reaching the end, we have
checked all the possible possibilities and can give the same errors as
before: One if there was a possibility that worked but was reserved;
and another if no possibility worked.
new file: ports/nrf/boards/raytac_mdbt50q-db-40/bootloader/6.0.0/pca10056_bootloader_6.0.0_s140.zip
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.h
new file: ports/nrf/boards/raytac_mdbt50q-db-40/mpconfigboard.mk
new file: ports/nrf/boards/raytac_mdbt50q-db-40/pins.c
When compiling for debug (-O0) the .text segment cannot fit the flash
region when MICROPY_ROM_TEXT_COMPRESSION=1, because the compiler does not
optimise away the large if-else chain used to select the correct compressed
string.
This commit enforces MICROPY_ROM_TEXT_COMPRESSION=0 when compiling for
debug (DEBUG=1).
The storage space of the advertisement name is not declared static, leading
to a random advertisement name. This commit fixes the issue by declaring
it static.
The Bluetooth link gets disconnected when connecting from a PC after 30-40
seconds. This commit adds handling of the data length update request. The
data length parameter pointer is set to NULL in the reply, letting the
SoftDevice automatically set values and use them in the data length update
procedure.
mp_keyboard_interrupt() triggers a compiler error because the function is
implicitly declared. This commit adds "py/runtime.h" to the includes.
Fixes issue #5732.
Changes are:
- The default manifest.py is moved to the variants directory (it's in
"boards" in other ports).
- The coverage variant now uses a custom manifest in its variant directory
to add frzmpy/frzstr.
- The frzmpy/frzstr tests are moved to variants/coverage/.
Polling mode will cause failures with the mass-erase command due to USB
timeouts, because the USB IRQs are not being serviced. Swiching from
polling to IRQ mode fixes this because the USB IRQs can be serviced between
page erases.
Note that when the flash is being programmed or erased the MCU is halted
and cannot respond to USB IRQs, because mboot runs from flash, as opposed
to the built-in bootloader which is in system ROM. But the maximum delay
in responding to an IRQ is the time taken to erase a single page, about
100ms for large pages, and that is short enough that the USB does not
timeout on the host side.
Recent tests have shown that in the current mboot code IRQ mode is pretty
much the same speed as polling mode (within timing error), code size is
slightly reduced in IRQ mode, and IRQ mode idles at about half of the power
consumption as polling mode.
This is treated more like a "delay before continuing" in the spec and
official tools and does not appear to be really needed. In particular,
downloading firmware is much slower with non-zero timeouts because the host
must pause by the timeout between sending each DFU_GETSTATUS to poll for
download/erase complete.
Supports hard and soft interrupts. In the current implementation, soft
interrupt callbacks will only be called when the VM is executing, ie they
will not be called during a blocking kernel call like k_msleep. And the
behaviour of hard interrupt callbacks will depend on the underlying device,
as well as the amount of ISR stack space.
Soft and hard interrupts tested on frdm_k64f and nucleo_f767zi boards.
Signed-off-by: Damien George <damien@micropython.org>
The implementation internally uses sector erase to wipe everything except
the sector(s) that mboot lives in (by erasing starting from
APPLICATION_ADDR).
The erase command can take some time (eg an STM32F765 with 2MB of flash
takes 8 to 10 seconds). This time is normally enough to make pydfu.py fail
with a timeout. The DFU standard includes a mechanism for the DFU device
to request a longer timeout as part of the get-status response just before
starting an operation. This timeout functionality has been implemented
here.
Before this commit the USB VCP TX ring-buffer used the basic implementation
where it can only be filled to a maximum of buffer size-1. For a 1024 size
buffer this means the largest packet that can be sent is 1023. Once a
packet of this size is sent the next byte copied in goes to the final byte
in the buffer, so must be sent as a 1 byte packet before the read pointer
can be wrapped around to the beginning. So in large streaming transfers,
watching the USB sniffer you basically get alternating 1023 byte packets
then 1 byte packets.
This commit changes the ring-buffer implementation to a scheme that doesn't
have the full-size limitation, and the USB VCP driver can now achieve a
constant stream of full-sized packets. This scheme introduces a
restriction on the size of the buffer: it must be a power of 2, and the
maximum size is half of the size of the index (in this case the index is
16-bit, so the maximum size would be 32767 bytes rounded to 16384 for a
power-of-2). But this is not a big limitation because the size of the
ring-buffer prior to this commit was restricted to powers of 2 because it
was using a mask-based method to wrap the indices.
For an explanation of the new scheme see
https://www.snellman.net/blog/archive/2016-12-13-ring-buffers/
The RX buffer could likely do with a similar change, though as it's not
read from in chunks like the TX buffer it doesn't present the same issue,
all that's lost is one byte capacity of the buffer.
USB VCP TX throughput is improved by this change, potentially doubling the
speed in certain cases.
Testing performed: That a card is successfully mounted on Pygamer with
the built in SD card slot
This module is enabled for most FULL_BUILD boards, but is disabled for
samd21 ("M0"), litex, and pca10100 for various reasons.
By passing through the I2C instance to the application callbacks, the
application can implement multiple I2C slave devices on different
peripherals (eg I2C1 and I2C2).
This commit also adds a proper rw argument to i2c_slave_process_addr_match
for F7/H7/WB MCUs, and enables the i2c_slave_process_tx_end callback.
Mboot is also updated for these changes.
Signed-off-by: Damien George <damien@micropython.org>
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
This commit factors the code for files and streaming to separate source
files (vfs_fat.c and gzstream.c respectively) and introduces an abstract
gzstream interface to make it easier to plug in different filesystems.
Signed-off-by: Damien George <damien@micropython.org>
There's no need to do a directory listing to search for the given firmware
filename, it just takes extra time and code size. Instead this commit
changes it so that the requested firmware file is opened immediately and
will abort if the file couldn't be opened. This also allows to specify
files in a directory.
Signed-off-by: Damien George <damien@micropython.org>
Previously, if FAT was not enabled but LFS1/2 was then MICROPY_PY_IO_FILEIO
would be disabled and file binary-mode was not supported.
Signed-off-by: Damien George <damien@micropython.org>
Since Actions passed on the previous commit, where this computed value
was checked against the specified value (if any), this is no net change,
except that we no longer need to specify it for particular boards or
ports.
Few peripherals are actually tested. However, USB, I2C and GPIO seem to work.
Most pins are silkscreened with the "PX00" style, so the board module
only includes the small number that are screened differently.
The default SPI, I2C, and UART are the ones on the EXT2 header. This is
arbitrary, but the I2C on this connector is shared with the on-board I2C
devices and the PCC header, making it the most versatile.
This introduces the new macro SAM_D5X_E5X. This is mostly the same
as SAMD51 before, except in a few places where a special case for
SAME54 is required
Commit 8675858465 switched to using the CMSIS
provided SystemInit function which sets VTOR to 0x00000000 (previously it
was 0x08000000). A VTOR of 0x00000000 will be correct on some MCUs but not
on others where the built-in bootloader is remapped to this address, via
__HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH().
To make sure mboot has the correct vector table, this commit explicitly
sets VTOR to the correct value of 0x08000000.
Signed-off-by: Damien George <damien@micropython.org>
I noticed that this code was referring to samd-specific functionality,
and isn't enabled except in one samd board (pewpew10). Move it.
There is incomplte support for _pew in mimxrt10xx which then caused build
errors; adding a #if guard to check for _pew being enabled fixes it.
The _pew module is not likely to be important on mimxrt but I'll leave the
choice to remove it to someone else.
There's no need to duplicate this functionality in mboot, the code provided
in stm32lib/CMSIS does the same thing and makes it easier to support other
MCU series.
Signed-off-by: Damien George <damien@micropython.org>
The flash functions in ports/stm32/flash.c are almost identical to those in
ports/stm32/mboot/main.c, so remove the duplicated code in mboot and use
instead the main stm32 code. This also allows supporting other MCU series.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes the low-level flash C functions usable by code other than
flashbdev.c (eg by mboot). Changes in this commit are:
- flash_erase() and flash_write() now return an errno error code, a
negative value on error.
- flash_erase() now automatically locks the flash, as well as unlocking it.
- flash_write() now automatically unlocks the flash, as well as locking it.
- flashbdev.c is modified for the above changes.
Signed-off-by: Damien George <damien@micropython.org>
irq.h is included by py/mphal.h but it's better to be explicit, eg if mboot
uses powerctrlboot.c.
Signed-off-by: Damien George <damien@micropython.org>
The irq.h file now just provides low-level IRQ definitions and priorities.
All Python binding definitions are moved to modmachine.h, with some
renaming of pyb -> machine, and also the machine_idle definition (was
pyb_wfi) is moved to modmachine.c.
The cc3200 and teensy ports are updated to build with these changes.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise the RMT will repeat pulses when using loop(True). This repeating
is due to a bug in the IDF which will be fixed in an upcoming release, but
for now the accepted workaround is to swap these calls, which should still
work in the fixed version of the IDF.
Fixes issue #6167.
With only `sp_func_proto_paren = remove` set there are some cases where
uncrustify misses removing a space between the function name and the
opening '('. This sets all of the related options to `force` as well.
When compiling with optimizations on, an issue occurs where the claimed_pins/never_reset_pins memory location is shared with another variable. This causes some bad memory read, so the USB pins ended up being reset. Setting these to have an alignment of 4 bytes resolves this.
Tested on nucleo_f746zg
There are a maximum of 8 USB endpoints and each has 2 buffer slots
(in/out). This commit add support for up to 8 endpoints and adds FIFO
configuration for USB profiles with 2xVCP on MCUs that have device-only USB
peripherals.
Tested on NUCLEO_WB55 in 2xVCP, 2xVCP+MSC and 2xVCP+MSC+HID mode.
Signed-off-by: Damien George <damien@micropython.org>
The ESP32 RMT peripheral has hardware support for a carrier frequency, and
this commit exposes it to Python with the keyword arguments carrier_freq
and carrier_duty_percent in the constructor. Example usage:
r = esp32.RMT(0, pin=Pin(2), clock_div=80, carrier_freq=38000, carrier_duty_percent=50)
This improves, but does not entirely fix, the broken links that result
from the autoapi change. It fixes module-level links, but class links
still do not work (e.g., /shared-bindings/displayio/Palette.html (5.0.x)
is now just /shared-bindings/displayio/#displayio.Palette).
Zephyr renamed CONFIG_FLOAT to CONFIG_FPU to better reflect its semantics
of enabling the hardware floating point unit (FPU) rather than enabling
toolchain-level floating point support (i.e., software floating point for
FPU-less socs).
Zephyr deprecated and then removed its stack_analyze function because it
was unsafe. Use the new zephyr thread analyzer instead and rename the
MicroPython function to zephyr.thread_analyze() to be more consistent with
the implementation.
Tested on mimxrt1050_evk.
The output now looks like this:
>>> zephyr.thread_analyze()
Thread analyze:
80004ff4 : unused 400 usage 112 / 512 (21 %)
rx_workq : unused 1320 usage 180 / 1500 (12 %)
tx_workq : unused 992 usage 208 / 1200 (17 %)
net_mgmt : unused 656 usage 112 / 768 (14 %)
sysworkq : unused 564 usage 460 / 1024 (44 %)
idle : unused 256 usage 64 / 320 (20 %)
main : unused 2952 usage 1784 / 4736 (37 %)
Sending more than 64 bytes to the USB CDC endpoint in HS mode will lead to
a hard crash. This commit fixes the issue, although there may be a better
fix from upstream TinyUSB in the future.
With this commit the code should work correctly regardless of the size of
StackType_t (it's actually 1 byte in size for the esp32's custom FreeRTOS).
Fixes issue #6072.
This commit implements an LED class with rudimentary parts of a pin C API
to support it. The LED class does not yet support setting an intensity.
This LED class is put in the machine module for the time being, until a
better place is found.
One LED is supported on TEENSY40 and MIMXRT1010_EVK boards.
Changes are:
- string0 is no longer built when building for host as the target, because
it'll be provided by the system libc and may in some cases clash with the
system one (eg on OSX).
- mp_int_t/mp_uint_t are defined in terms of intptr_t/uintptr_t to support
both 32-bit and 64-bit builds.
- Configuration values which are the default in py/mpconfig.h are removed
from mpconfigport.h to make the configuration a bit more minimal, eg as
a better starting point for new ports.
These calls were all moved into `main.c`, however this call was not
removed from litex. As a result, litex was calling `board_init()` twice.
This is currently not a problem, as `fomu` is able to be initialized
twice without issue, however future boards may have issue with this.
This fixes#2991.
Signed-off-by: Sean Cross <sean@xobs.io>
Microwatt may have firmware that places data in r3, which was used to
detect microwatt vs powernv. This breaks the existing probing of the UART
type in this powerpc port.
Instead build only the appropriate UART into the firmware, selected by
passing the option UART=potato or UART=lpc_serial to the Makefile.
A future enhancement would be to parse the device tree and configure
MicroPython based on the settings.
The code previously called rtc_get_reset_reason which is a "raw" reset
cause. The ESP-IDF massages that for the proper reset cause available from
esp_reset_reason.
Fixes issue #5134.
From the change:
// xtensa has more registers than an instruction can address. The 16 that
// can be addressed are called the "window". When a function is called or
// returns the window rotates. This allows for more efficient function calls
// because ram doesn't need to be used. It's only used if the window wraps
// around onto itself. At that point values are "spilled" to empty spots in
// the stack that were set aside. When the window rotates back around (on
// function return), the values are restored into the register from ram.
// So, in order to read the values in the stack scan we must make sure all
// of the register values we care about have been spilled to RAM. Luckily,
// there is a HAL call to do it. There is a bit of a race condition here
// because the register value could change after it's been restored but that
// is unlikely to happen with a heap pointer while we do a GC.
Fixes#2907
* Fix flash writes that don't end on a sector boundary. Fixes#2944
* Fix enum incompatibility with IDF.
* Fix printf output so it goes out debug UART.
* Increase stack size to 8k.
* Fix sleep of less than a tick so it doesn't crash.
Add configuration which otherwise has to be set via the UI so the file is
more self-contained, and remove configuration which is not needed because
it's the same as the default. The major change here is that for a while
now Appveyor has been using Visual Studio 2015 by default while we still
want to support 2013.
Older implementations deal with infinity/negative zero incorrectly. This
commit adds generic fixes that can be enabled by any port that needs them,
along with new tests cases.
The linker script was included in the "$^" inputs, causing the build to
fail:
LINK build/firmware.elf
powerpc64le-linux-gnu-ld: error: linker script file 'powerpc.lds' appears multiple times
As a fix the linker script is left as a dependency of the elf, but only the
object files are linked.
The PWM driver uses a double buffer for the PWM timing array, one in
current use and the other one to update when changing duty parameters.
The issue was that once the duty parameters were changed the updated buffer
was applied immediately without synchronising to the start of the PWM
period. By moving the buffer toggling/swapping to the interrupt when the
cycle is done there are no more glitches.
This pulls all common functionality into `shared-bindings` and keeps
platform-specific code inside `nrf`. Additionally, this performs most
validation in the `shared-bindings` site.
The only validation that occurs inside platform-specific `common-hal`
code is related to timeout limits that are platform-specific.
Additionally, all documentation is now inside the `shared-bindings`
directory.
Signed-off-by: Sean Cross <sean@xobs.io>
The previous setting of `1` meant that the bluetooth system couldn't be
used when the watchdog timer was enabled.
Signed-off-by: Sean Cross <sean@xobs.io>
As part of the reset process, save the current tick count to an
uninitialized memory location. That way, the current tick value will be
preserved across reboots.
A reboot will cause us to lose a certain number of ticks, depending on
how long a reboot takes, however if reboots are infrequent then this
will not be a large amount of time lost.
Signed-off-by: Sean Cross <sean@xobs.io>
For `microcontroller.reset()`, don't manually call NVIC_SystemReset().
Instead, call the `port_reset()` in case the port wants to do any
cleanup.
Signed-off-by: Sean Cross <sean@xobs.io>
This finishes the rework of the exception handler, which is once
again stored inside the watchdog timer module.
This also implements a `watchdog_reset()` that is used to disable the
RAISE watchdog, if one is enabled.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds an exception to be raised when the WatchDogTimer times out.
Note that this currently causes a HardFault, and it's not clear why it's
not behaving properly.
Signed-off-by: Sean Cross <sean@xobs.io>
This enables WDT support for Simmel. Other platforms cannot yet use
WDT because it overflows their flash storage.
Enable CIRCUITPY_WDT support for the nrf target.
Signed-off-by: Sean Cross <sean@xobs.io>
With the WDT changes, building Circuit Python results in the following error:
/opt/gcc-arm-none-eabi-9-2019-q4-major/bin/../lib/gcc/arm-none-eabi/9.2.1/../../../../arm-none-eabi/bin/ld: section .ARM.exidx LMA [00000000000621c8,00000000000621cf] overlaps section .data LMA [00000000000621c8,0000000000062383]
This is because unwinding data is getting generated, but has nowhere to go.
Re-enable this data in the linker script so it is saved.
Signed-off-by: Sean Cross <sean@xobs.io>
If interrupts are disabled, then calling sd_* functions will hardfault.
Instead, assume that it's safe to write if interrupts are disabled.
Signed-off-by: Sean Cross <sean@xobs.io>
ARM recommends issuing a DSB instruction propr to issuing WFI, as it is
required on many parts suchas Cortex-M7. This is effectively a no-op on
the Cortex-M4 used in most NRF parts, however it ensures that we won't
be surprised when new parts come out.
See
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dai0321a/BIHICBGB.html
for more information.
Signed-off-by: Sean Cross <sean@xobs.io>
In order to ensure we don't have any outstanding requests, disable
interrupts prior to issuing `WFI`.
As part of this process, check to see if there are any pending USB
requests, and only execute the `WFI` if there is no pending data.
This fixes#2855 on NRF.
Signed-off-by: Sean Cross <sean@xobs.io>
On NRF, the `rtc_reset()` function is never called. As a result,
calls to `time.time()` return a cryptic error>
```
>>> import time
>>> time.time()
'' object has no attribute 'datetime'
>>>
```
This is because `MP_STATE_VM(rtc_time_source)` is not initialized
due to `rtc_reset()` never being called.
If `CIRCUITPY_RTC` is enabled, call `rtc_reset()` as part of the
`reset_port()` call. This ensures that `time.time()` works as expected.
Signed-off-by: Sean Cross <sean@xobs.io>
The timeout value is calculated by the common-hal layer now, so we don't
need to be quite so clever about calculating it here.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a field to allow specifying a timeout when initiating advertising.
As part of this, add a new property to determine if the device is still
advertising.
Additionally, have the `anonymous` property require a timeout, and set
the timeout to the maximum possible value if no timeout is specified.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a new parameter to the `start_advertising()` function to enable
anonymous advertising. This forces a call to `sd_ble_gap_privacy_set()`
with `privacy_mode` set to `BLE_GAP_PRIVACY_MODE_DEVICE_PRIVACY` and
`private_addr_type` set to
`BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE`.
With this, addresses will cycle at a predefined rate (currently once
every 15 minutes).
Signed-off-by: Sean Cross <sean@xobs.io>
Store the RTC value in the .uninitialized section, but make sure to
flank it with some known values. That way we can determine if the RTC
value has been initialized, or if it's random uninitialized garbage.
As part of this, add a `common_hal_rtc_init()` routine to determine if
the value is correct, or reset it to 0 if it is not valid.
Signed-off-by: Sean Cross <sean@xobs.io>
Circuit Python supports saving a single word of data across reboots.
Previously, this data was placed immediately following the .bss.
However, this appeared to not work, as Circuit Python zeroes out the
heap when it starts up, and the heap begins immediately after the .bss.
Switch to using the new .uninitialized section in order to store this
word across resets.
Signed-off-by: Sean Cross <sean@xobs.io>
Previously, it was placed following .bss. However, now that there is a
new section after .bss, the heap must be moved forward.
Signed-off-by: Sean Cross <sean@xobs.io>
This section immediately follows the .bss section, and is designed to
contain uninitialized variables that should persist across reboots.
The section is placed directly after .bss, under the theory that the
size of Circuit Python's .bss + .data is bigger than the bootloader's
.bss + .data, so there is less likely to be a conflict.
Signed-off-by: Sean Cross <sean@xobs.io>
Commit 6cea369b89 updated the TinyUSB
submodule to a version based on nrfx v2.0.0. This commit updates the nrf
port to work with the latest TinyUSB and nrfx v2.0.0.
Because it can confuse older versions of gcc. Instead use the correct
instruction for Thumb vs Thumb-2 (sub vs subs) so the assembler emits the
2-byte instruction.
Related to commit 1aa9ff9141.
Prior to e0905e85a7 it was possible to
disable btree support on build. This patch allows to configure btree
support on make again and also the two new introduced options for FAT and
LFS2 filesystems.
SPIM3 is faster than all other SPI blocks, and is capable of generating
a 32 MHz clock. However, it cannot be used at the same time as the BLE
radio without dedicating an additional 8 kB of RAM to it.
Therefore, some boards may want to disable this. Support pre-defining
NRFX_SPIM3_ENABLED on the command line to disable it on some bords.
Signed-off-by: Sean Cross <sean@xobs.io>
This commit allows the user to set/get the GAP device name used by service
0x1800, characteristic 0x2a00. The usage is:
BLE.config(gap_name="myname")
print(BLE.config("gap_name"))
As part of this change the compile-time setting
MICROPY_PY_BLUETOOTH_DEFAULT_NAME is renamed to
MICROPY_PY_BLUETOOTH_DEFAULT_GAP_NAME to emphasise its link to GAP and this
new "gap_name" config value. And the default value of this for the NimBLE
bindings is changed from "PYBD" to "MPY NIMBLE" to be more generic.
Ujson should only worry about whitespace before JSON. This becomes apparent when you are using MP stream protocol to read directly from input buffers.
When you attempt to read(1) on a UART (and possibly other protocols) you have to wait for either the byte or the timeout.
Fixes:
- Waiting for a timeout after you have completed reading a correct and complete JSON off the input.
- Raising an OSError after reading a correct and complete JSON off the input.
- Eating more data than semantically owned off the input buffer.
- Blocking to start parsing JSON until the entire JSON body has been loaded into a potentially large, contiguous Python object.
Code you would write before:
```
line = board_busio_uart_port.read_line()
json_dict = json.loads(line)
```
or reaching for fixed buffers and swapping them around in Python.
Code that did not work before that does now:
```
json_dict = json.load(board_busio_uart_port)
```
- This removes the need for intermediate copies of data when reading JSON from micropython stream protocol inputs.
- It also increases total application speed by parsing JSON concurrently with receiving on boards that read from UART via DMA.
- It simplifies code that users write while improving their apps.
vectorio builds on m4 express feather
Concrete shapes are composed into a VectorShape which is put into a displayio Group for display.
VectorShape provides transpose and x/y positioning for shape implementations.
Included Shapes:
* Circle
- A radius; Circle is positioned at its axis in the VectorShape.
- You can freely modify the radius to grow and shrink the circle in-place.
* Polygon
- An ordered list of points.
- Beteween each successive point an edge is inferred. A final edge closing the shape is inferred between the last
point and the first point.
- You can modify the points in a Polygon. The points' coordinate system is relative to (0, 0) so if you'd like a
top-center justified 10x20 rectangle you can do points [(-5, 0), (5, 0), (5, 20), (0, 20)] and your VectorShape
x and y properties will position the rectangle relative to its top center point
* Rectangle
A width and a height.
This commit fixes the behaviour of socket.getaddrinfo on the ESP32 so it
raises an OSError when the name resolution fails instead of returning a []
or a resolution for 0.0.0.0.
Tests are added (generic and ESP32-specific) to verify behaviour consistent
with CPython, modulo the different types of exceptions per MicroPython
documentation.
The ones that are moved out of iRAM should not need to be there, because
either they call functions in iROM (eg mp_hal_stdout_tx_str), or they are
only ever called from a function in iROM and not from an interrupt (eg
ets_esf_free_bufs).
This frees up about 800 bytes of iRAM.
The zephyr build system supports merging application-level board
configurations, so there is no need to reproduce this functionality in
MicroPython.
If CONF_FILE is not explicitly set, then the zephyr build system looks for
prj.conf in the application directory. Therefore we rename the MicroPython
prj_base.conf to prj.conf.
Furthermore, if the zephyr build system finds boards/$(BOARD).conf in the
application directory, it merges that configuration with prj.conf.
Therefore we rename all the MicroPython board .conf files and move them
into a boards/ directory.
The minimal configuration, prj_minimal.conf, is left in the application
directory because it is used as an explicitly set CONF_FILE in
make-minimal.
Simmel had USB HID disabled in order to save space. However, the board
configuration did not set USB_DEVICES, causing it to inherit the default
device bouquet of MSC,CDC,MIDI,HID. This in turn caused HID to be included
in the USB Configuration Descriptor.
For some reason, this was not a problem in an earlier version of tinyusb or
circuitpython. However, in the most recent version this has rightfully
caused asserts to appear during configuration.
Re-enable USB_HID for now, as it doesn't add too much in terms of space.
We may disable it again later on if we become pressed for space.
Signed-off-by: Sean Cross <sean@xobs.io>
This commit adds several small items to improve the support for OTA
updates on an esp32:
- a partition table for 4MB flash modules that has two OTA partitions ready
to go to do updates
- a GENERIC_OTA board that uses that partition table and that enables
automatic roll-back in the bootloader
- a new esp32.Partition.mark_app_valid_cancel_rollback() class-method to
signal that the boot is successful and should not be rolled back at the
next reset
- an automated test for doing an OTA update
- documentation updates
GPIO interrupts can occur when the flash ROM cache is in use and so the
GPIO interrupt handler must be in iRAM. This commit moves the handler to
iRAM, and also moves mp_sched_schedule to iRAM which is called by
pin_intr_handler.
As part of this fix the Pin class can no longer support hard=True in the
Pin.irq() method, because the VM and runtime are too big to put in iRAM.
Fixes#5714.
This was not added as part of the initial v7.0.1 patchset because
.hex files are in this project's .gitignore, and so git ignored it.
Signed-off-by: Sean Cross <sean@xobs.io>
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port. This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.
Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.
The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
But only when bluetooth is enabled, i.e. if building the dev or coverage
variants, and we have libusb available.
Update travis to match, i.e. specify the variant when doing
`make submodules`.
This commit adds full support to the unix port for Bluetooth using the
common extmod/modbluetooth Python bindings. This uses the libusb HCI
transport, which supports many common USB BT adaptors.
This change is made for two reasons:
1. A 3rd-party library (eg berkeley-db-1.xx, axtls) may use the system
provided errno for certain errors, and yet MicroPython stream objects
that it calls will be using the internal mp_stream_errno. So if the
library returns an error it is not known whether the corresponding errno
code is stored in the system errno or mp_stream_errno. Using the system
errno in all cases (eg in the mp_stream_posix_XXX wrappers) fixes this
ambiguity.
2. For systems that have threading the system-provided errno should always
be used because the errno value is thread-local.
For systems that do not have an errno, the new lib/embed/__errno.c file is
provided.
this non-"express" board is nearly full. Right now it's actually possible
just to disable the "compare" module, but as this leaves it packed
pretty full I prefer to fully disable it in order to avoid the topic
returning again soon.
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
This commit consolidates a number of check_esp_err functions that check
whether an ESP-IDF return code is OK and raises an exception if not. The
exception raised is an OSError with the error code as the first argument
(negative if it's ESP-IDF specific) and the ESP-IDF error string as the
second argument.
This commit also fixes esp32.Partition.set_boot to use check_esp_err, and
uses that function for a unit test.
This commit adds an idf_heap_info(capabilities) method to the esp32 module
which returns info about the ESP-IDF heaps. It's useful to get a bit of a
picture of what's going on when code fails because ESP-IDF can't allocate
memory anymore. Includes documentation and a test.
Previously, we were using v6.1.1 which worked, but was unsupported.
v7.0.1 is the first version of s140 that supports the nRF52833.
Signed-off-by: Sean Cross <sean@xobs.io>
Allow for setting various softradio memory settings as part of a
board in order to support lower-memory configurations. If a
parameter is unspecified then the previously-defined value is used.
Signed-off-by: Sean Cross <sean@xobs.io>
Conditionally set variables such as the softdevice RAM size, bootloader
size, and the spi m3 buffer size. This allows ports to adjust these
values to suit their needs.
Signed-off-by: Sean Cross <sean@xobs.io>
The BLE Config area needs to be subtracted from the size of the firmware.
THis is because the firmware is counted by walking backwards from the end
of memory, and the BLE config area is placed lower in memory than the
firmware. Subtracting the BLE config size ensures the internal flash
filesystem doesn't try to use the firmware as storage.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds preliminary support for the nRF52833, which is a variant of
the nRF52840 with half the RAM, half the flash, and fewer peripherals.
Signed-off-by: Sean Cross <sean@xobs.io>
Ports can set CIRCUITPY_RGBMATRIX and CIRCUITPY_FRAMEBUFFERIO to 0
in their .mk file in order to prevent these from being built. This
is necessary for resource-constrained devices.
Signed-off-by: Sean Cross <sean@xobs.io>
In mboot, the ability to override the USB vendor/product id's was added
back in 5688c9ba09. However, when the main
firmware is turned into a DFU file the default VID/PID are used there.
pydfu.py doesn't care about this but dfu-util does and prevents its use
when the VID/PID don't match.
This commit exposes BOOTLOADER_DFU_USB_VID/PID as make variables, for use
on either command line or mpconfigboard.mk, to set VID/PID in both mboot
and DFU files.
Add -Wdouble-promotion and -Wfloat-conversion for most ports to ban out
implicit floating point conversions, and add extra Travis builds using
MICROPY_FLOAT_IMPL_FLOAT to uncover warnings which weren't found
previously. For the unix port -Wsign-comparison is added as well but only
there since only clang supports this but gcc doesn't.
Initially some of these were found building the unix coverage variant on
MacOS because that build uses clang and has -Wdouble-promotion enabled, and
clang performs more vigorous promotion checks than gcc. Additionally the
codebase has been compiled with clang and msvc (the latter with warning
level 3), and with MICROPY_FLOAT_IMPL_FLOAT to find the rest of the
conversions.
Fixes are implemented either as explicit casts, or by using the correct
type, or by using one of the utility functions to handle floating point
casting; these have been moved from nativeglue.c to the public API.
This gets all the purely internal references. Some uses of
protomatter/Protomatter/PROTOMATTER remain, as they are references
to symbols in the Protomatter C library itself.
I originally believed that there would be a wrapper library around it,
like with _pixelbuf; but this proves not to be the case, as there's
too little for the library to do.
Manually specify available modules and disable any modules
that are currently unsupported on the litex target.
Signed-off-by: Sean Cross <sean@xobs.io>
Now that error string compression is supported it's more important to have
consistent error string formatting (eg all lowercase English words,
consistent contractions). This commit cleans up some of the strings to
make them more consistent.
This macro is used to implement global serialisation, typically by
disabling IRQs. On the unix port, if threading is enabled, use the
existing thread mutex (that protects the thread list structure) for this
purpose. Other places in the code (eg the scheduler) assume this macro
will provide serialisation.
Based on eg 1e6fd9f2b4, it's understood that
the intention for unix builds is that regular builds disable assert, but
the coverage build should set -O0 and enable asserts.
It looks like this didn't work (even before variants were introduced, eg at
v1.11) -- coverage always built with -Os and -DNDEBUG.
This commit makes it possible for variants to have finer-grained control
over COPT flags, and enables assert() and -O0 on coverage builds.
Other variants already match the defaults so they have been updated.
TimeoutError was added back in 077812b2ab for
the cc3200 port. In f522849a4d the cc3200
port enabled use of it in the socket module aliased to socket.timeout. So
it was never added to the builtins. Then it was replaced by
OSError(ETIMEDOUT) in 047af9b10b.
The esp32 port enables this exception, since the very beginning of that
port, but it could never be accessed because it's not in builtins.
It's being removed: 1) to not encourage its use; 2) because there are a lot
of other OSError subclasses which are not defined at all, and having
TimeoutError is a bit inconsistent.
Note that ports can add anything to the builtins via MICROPY_PORT_BUILTINS.
And they can also define their own exceptions using the
MP_DEFINE_EXCEPTION() macro.
The iMX RT has a separate wake up controller, the GPC, that replaces
the NVIC when asleep. It adds the ability to only wake up on certain
interrupts. It seems that it requires at least one enabled interrupt
in the NVIC to turn on it's wake up circuitry. It doesn't need to
be the same interrupt as the wake up signal. For example, the RTC
in the SNVS can wake us up if a USB interrupt is enabled. Before
then it won't work. So, we enable the SNVS interrupt on start up
so it can wake us up.
This commit makes all functions and function wrappers in modubinascii.c
STATIC and conditional on the MICROPY_PY_UBINASCII setting, which will
exclude the file from qstr/ compressed-string searching when ubinascii is
not enabled. The now-unused modubinascii.h header file is also removed.
The cc3200 port is updated accordingly to use this module in its entirety
instead of providing its own top-level definition of ubinascii.
This was originally like this because the cc3200 port has its own ubinascii
module which referenced these methods. The plan appeared to be that the
API might diverge (e.g. hardware crc), but this should be done similar to
I2C/SPI via a port-specific handler, rather than the port having its own
definition of the module. Having a centralised module definition also
enforces consistency of the API among ports.
This commit changes the default filesystem type for esp32 to littlefs v2.
This port already enables both VfsFat and VfsLfs2, so either can be used
for the filesystem, and existing systems that use FAT will still work.
This commit changes the esp8266 boards to use littlefs v2 as the
filesystem, rather than FAT. Since the esp8266 doesn't expose the
filesystem to the PC over USB there's no strong reason to keep it as FAT.
Littlefs is smaller in code size, is more efficient in use of flash to
store data, is resilient over power failure, and using it saves about 4k of
heap RAM, which can now be used for other things.
This is a backwards incompatible change because all existing esp8266 boards
will need to update their filesystem after installing new firmware (eg
backup old files, install firmware, restore files to new filesystem).
As part of this commit the memory layout of the default board (GENERIC) has
changed. It now allocates all 1M of memory-mapped flash to the firmware,
so the filesystem area starts at the 2M point. This is done to allow more
frozen bytecode to be stored in the 1M of memory-mapped flash. This
requires an esp8266 module with 2M or more of flash to work, so a new board
called GENERIC_1M is added which has the old memory-mapping (but still
changed to use littlefs for the filesystem).
In summary there are now 3 esp8266 board definitions:
- GENERIC_512K: for 512k modules, doesn't have a filesystem.
- GENERIC_1M: for 1M modules, 572k for firmware+frozen code, 396k for
filesystem (littlefs).
- GENERIC: for 2M (or greater) modules, 968k for firmware+frozen code,
1M+ for filesystem (littlefs), FAT driver also included in firmware for
use on, eg, external SD cards.
The SPI flash on current Fomu firmware is slow. Circuitpython runs
XIP from SPI flash, and so execution time can also be slow. Ordinarily
this isn't a problem, however certain operations are time-sensitive.
In particular, USB function needs to be handled quickly in order to
prevent the host from re-enumerating the device.
Place several critical TinyUSB structures into RAM, as well as several
hot functions that are frequently called. This reduces execution time
at the expense of system memory, and greatly improves system stability.
Signed-off-by: Sean Cross <sean@xobs.io>
Following up to 5e6cee07ab, some systems (eg
FreeBSD 12.0 64-bit) will crash if the stack-overflow margin is too small.
It seems the margin of 8192 bytes (or thereabouts) is always needed. This
commit adds this much margin if the requested stack size is too small.
Fixes issue #5824.
These were found by buiding the unix coverage variant on macOS (so clang
compiler). Mostly, these are fixing implicit cast of float/double to
mp_float_t which is one of those two and one mp_int_t to size_t fix for
good measure.
These are mainly used by the previous version of uasyncio which is now
replaced by a newer version, with built-in C module _uasyncio. Saves about
1300 bytes of flash.
https://www.python.org/dev/peps/pep-0475/
This implements something similar to PEP 475 on the unix port, and for the
VfsPosix class.
There are a few differences from the CPython implementation:
- Since we call mp_handle_pending() between any ENITR's, additional
functions could be called if MICROPY_ENABLE_SCHEDULER is enabled, not
just signal handlers.
- CPython only handles signal on the main thread, so other threads will
raise InterruptedError instead of retrying. On MicroPython,
mp_handle_pending() will currently raise exceptions on any thread.
A new macro MP_HAL_RETRY_SYSCALL is introduced to reduce duplicated code
and ensure that all instances behave the same. This will also allow other
ports that use POSIX-like system calls (and use, eg, VfsPosix) to provide
their own implementation if needed.
The stack size adjustment for detecting stack overflow in threads was not
taking into account that the requested stack size could be <= 8k, in which
case the subtraction would overflow. This is fixed in this commit by
ensuring that the adjustment can't be more than the available size.
This fixes the test tests/thread/thread_stacksize1.py which sometimes
crashes with a segmentation fault because of an uncaught NLR jump, which is
a "maximum recursion depth exceeded" exception.
Suggested-by: @dpgeorge
ports/atmel-samd/boards/bdmicro_vina_m0/board.c
ports/atmel-samd/boards/bdmicro_vina_m0/mpconfigboard.h
ports/atmel-samd/boards/bdmicro_vina_m0/mpconfigboard.mk
ports/atmel-samd/boards/bdmicro_vina_m0/board.c
This board includes the newly added MX25L51245G 64MB SPI flash chip
for the CircuitPython file system. Also included is the PCF2129T/2,518
high accuracy, battery backed, RTC. Also includes an independent USB
HOST connector in addition to USB DEVICE making it easy to connect USB
peripherals. Designed mainly as a general purpose module to piggy back
onto application-specific boards, it can also run low power standalone
in harsh environments for data logging and other control applications
using an appropriate enclosure.
Has been extensively tested with CircuitPython and works well.
Restructures the STM port of Circuitpython to be more generic about the STM32 chip lines to support
the F7 and H7 series of chips. Adds the new Packages directory to organize different chip layouts
between lines. Makes general changes to the Makefile to condense board-level flags to the minimum
and support the new chip series. Adds the new chip line to the Peripherals directory, along with
new python tools used to generate peripheral text automatically in the tools/ directory.
To enable lazy loading of submodules (among other things), which is very
useful for MicroPython libraries that want to have optional subcomponents.
Disabled explicitly on minimal ports.
This function is not used by the core but having it as part of the build
allows it to be used by user C modules, or board extensions. The linker
won't include it in the final firmware if it remains unused.
This removes the port-specific definition of MP_PLAT_PRINT_STRN on the
windows port, so that the default mp_hal_stdout_tx_strn_cooked() is always
used. This fixes releasing the GIL during the call to write() (this was
missed in bc3499f010).
Also, mp_hal_dupterm_tx_strn() was defined but never used anywhere so it is
safe to delete it.
This removes the port-specific definition of MP_PLAT_PRINT_STRN on the unix
port. Since fee7e5617f this is no longer a
single function call so we are not really optimising anything over using
the default definition of MP_PLAT_PRINT_STRN which calls
mp_hal_stdout_tx_strn_cooked().
Zephyr v2.2 reworked its gpio api to support linux device tree bindings and
pin logical levels. This commit updates the zephyr port's machine.Pin
class to replace the deprecated gpio api calls with the new supported gpio
api. This resolves several build warnings.
Tested on frdm_k64f and mimxrt1050_evk boards.
The "led" argument is always a pointer to the GPIO port, or'd with the pin
that the LED is on, so testing that it is "1" is unnecessary. The type of
"led" is also changed to uint32_t so it can properly hold a 32-bit pointer.
Updating the LED0 state from systick handler ensures LED0 is always
consistent with its flash rate regardless of other processing going on in
either interrupts or main. This improves the visible stability of the
bootloader, rather than LED0 flashing somewhat randomly at times.
This commit also changes the LED0 flash rate depending on the current state
of DFU, giving slightly more visual feedback on what the device is doing.
Adds support in the zephyr port to execute main.py if the file system is
enabled and the file exists. Existing support for executing a main.py
frozen module is preserved, since pyexec_file_if_exists() works just
like pyexec_frozen_module() if there's no vfs.
Enables the zephyr usb device stack and mass storage class on the
mimxrt1050_evk board. The mass storage class is backed by the sdhc disk
access driver, so it's now possible to browse and modify the contents of
the SD card from a USB host (your PC). This is in preparation to support
writing a main.py script to the SD card, and then executing it after the
next reset.
Adds support in the zephyr port to mount a file system if a block device
(sdhc disk access or flash area) is available. The mount point is either
"/sd" or "/flash" depending on the type of block device.
Tested with an sdhc disk access block device and fatfs on the
mimxrt1050_evk board.
Tested with a flash area block device and littlefs on the reel_board.
This commit adds micropython.heap_locked() which returns the current
lock-depth of the heap, and can be used by Python code to check if the heap
is locked or not. This new function is configured via
MICROPY_PY_MICROPYTHON_HEAP_LOCKED and is disabled by default.
This commit also changes the return value of micropython.heap_unlock() so
it returns the current lock-depth as well.
This is an extremely minimal port to the NXP i.MX RT, in the style of the
SAMD port It's largely based on the TinyUSB mimxrt implementation, using
the NXP SDK. It currently supports the Teensy 4.0 board with a REPL over
the USB-VCP interface.
This commit also adds the NXP SDK submodule (also from TinyUSB) to
lib/nxp_driver.
Note: if you already have the tinyusb submodule initialized recursively you
will need to run the following as the tinyusb sub-submodules have been
rearranged (upstream):
git submodule deinit lib/tinyusb
rm -rf .git/modules/lib/tinyusb
git submodule update --init lib/tinyusb
This makes a cleaner separation between the: driver, HCI UART and BT stack.
Also updated the naming to be more consistent (mp_bluetooth_hci_*).
Work done in collaboration with Jim Mussared aka @jimmo.
Move extmod/modbluetooth_nimble.* to extmod/nimble. And move common
Makefile lines to extmod/nimble/nimble.mk (which was previously only used
by stm32). This allows (upcoming) btstack to follow a similar structure.
Work done in collaboration with Jim Mussared aka @jimmo.
sys.stdout.flush() is needed on CPython to flush the output, and the change
in this commit makes such an expression also work on MicroPython (although
MicroPython doesn't actual need to do any flushing).
Matches the implementations of the NRF and Atmel ports. TIM7 is used as it does not have a tied pin. Contains some register micromanagement since HAL support for the TIM7 timer is limited.
This string is recognised by uncrustify, to disable formatting in the
region marked by these comments. This is necessary in the qstrdef*.h files
to prevent modification of the strings within the Q(...). In other places
it is used to prevent excessive reformatting that would make the code less
readable.
testing performed:
* successfully store and retrieve a 500kB file on the flash
* square wave output on each pin appears on o'scope
* board.SPI(), board.SERIAL(), board.I2C() all construct
If the built-in input() is enabled (which it is by default) then it needs
some form of readline, so supply it with one when MICROPY_USE_READLINE=0.
Fixes issue #5658.
This changes the signal used to trigger garbage collection from SIGUSR1 to
SIGRTMIN + 5. SIGUSR1 is quite common compared to SIGRTMIN (measured by
google search results) and is more likely to conflict with libraries that
may use the same signal.
POSIX specifies that there are at least 8 real-time signal so 5 was chosen
as a "random" number to further avoid potential conflict with libraries
that may use SIGRTMIN or SIGRTMAX.
Also, if we ever have a `usignal` module, it would be nice to leave SIGUSR1
and SIGUSR2 free for user programs.
The "random" module no longer uses the hardware RNG (the extmod version of
this module has a pseudo-random number generator), so the config option
MICROPY_PY_RANDOM_HW_RNG is no longer meaningful. This commit replaces it
with MICROPY_HW_ENABLE_RNG, which controls whether the hardware RNG is
included in the build.
The install target is current broken when PROG is used to override the
default executable name. This fixes it by removing the redundant TARGET
variable and uses PROG directly instead.
The install and uninstall targets are also moved to the common unix
Makefile so that all variants can be installed in the same way.
Currently it is not possible to override PREFIX when installing micropython
using the makefile. It is common practice to be able to run something like
this:
$ make install PREFIX=/usr DESTDIR=/tmp/staging
This fixes such usage.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX. It also reduces code size by a
small amount on some ports.
The default value for MICROPYPATH used in unix/main.c is
"~/.micropython/lib:/usr/lib/micropython" which has 2 problems when used in
the Windows port:
- it has a ':' as path separator but the port uses ';' so the entire string
is effectively discarded since it gets interpreted as a single path which
doesn't exist
- /usr/lib/micropython is not a valid path in a standard Windows
environment
Override the value with a suitable default.
If the exception doesn't need printf-style formatting then calling
mp_raise_msg is more efficient. Also shorten exception messages to match
style in core and other ports.
open source and radiation tested hardware + software platform for small satellites called CubeSats. See pycubed.org for more info. See quickstart.pycubed.org for lots of circuitpython examples
It's not needed. The C integer implicit promotion rules mean that the
uint8_t of the incoming character is promoted to a (signed) int, matching
the type of interrupt_char. Thus the uint8_t incoming character can never
be equal to -1 (the value of interrupt_char that indicate that interruption
is disabled).
The mp_keyboard_interrupt() function does exactly what is needed here, and
using it gets ctrl-C working when MICROPY_ENABLE_SCHEDULER is enabled on
these ports (and MICROPY_ASYNC_KBD_INTR is disabled).
This is a more logical place to clear the KeyboardInterrupt traceback,
right before it is set as a pending exception. The clearing is also
optimised from a function call to a simple store of NULL.
It was originally in IRAM due to the linker script specification, but
since the function moved from lib/utils/interrupt_char.c to py/scheduler.c
it needs to be put back in IRAM.
This function is tightly coupled to the state and behaviour of the
scheduler, and is a core part of the runtime: to schedule a pending
exception. So move it there.
Pending exceptions would otherwise be handled later on where there may not
be an NLR handler in place.
A similar fix is also made to the unix port's REPL handler.
Fixes issues #4921 and #5488.
Previous behaviour is when this argument is set to "true", in which case
the function will raise any pending exception. Setting it to "false" will
cancel any pending exception.
Enables the littlefs (v1 and v2) filesystems in the zephyr port.
Example usage with the internal flash on the reel_board or the
rv32m1_vega_ri5cy board:
import os
from zephyr import FlashArea
bdev = FlashArea(FlashArea.STORAGE, 4096)
os.VfsLfs2.mkfs(bdev)
os.mount(bdev, '/flash')
with open('/flash/hello.txt','w') as f:
f.write('Hello world')
print(open('/flash/hello.txt').read())
Things get a little trickier with the frdm_k64f due to the micropython
application spilling into the default flash storage partition defined
for this board. The zephyr build system doesn't enforce the flash
partitioning when mcuboot is not enabled (which it is not for
micropython). For now we can demonstrate that the littlefs filesystem
works on frdm_k64f by constructing the FlashArea block device on the
mcuboot scratch partition instead of the storage partition. Do this by
replacing the FlashArea.STORAGE constant above with the value 4.
Introduces a new zephyr.FlashArea class that uses the zephyr flash map
api to implement the uos.AbstractBlockDev protocol. The flash driver is
enabled on the frdm_k64f board, reel_board, and rv32m1_vega_ri5cy board.
The standard and extended block device protocols are both supported,
therefore this class can be used with file systems like littlefs which
require the extended interface.
Enables the fatfs filesystem in the zephyr port.
Example usage with an SD card on the mimxrt1050_evk board:
import zephyr, os
bdev = zephyr.DiskAccess('SDHC')
os.VfsFat.mkfs(bdev)
os.mount(bdev, '/sd')
with open('/sd/hello.txt','w') as f:
f.write('Hello world')
print(open('/sd/hello.txt').read())
Introduces a new zephyr.DiskAccess class that uses the zephyr disk
access api to implement the uos.AbstractBlockDev protocol. This can be
used with any type of zephyr disk access driver, which currently
includes SDHC, RAM, and FLASH implementations. The SDHC driver is
enabled on the mimxrt1050_evk board.
Only the standard block device protocol (without the offset parameter)
can be supported with the zephyr disk access api, therefore this class
cannot be used with file systems like littlefs which require the
extended interface. In the future it may be possible to implement the
extended interface in a new class using the zephyr flash api.
CPython also has os.environ, which should be used instead of os.getenv()
due to caching in the os.environ mapping. But for MicroPython it makes
sense to only implement the basic underlying methods, ie getenv/putenv/
unsetenv.
This adds a -h option to print the usage help text and adds a new, shorter
error message that is printed when invalid arguments are given. This
behaviour follows CPython (and other tools) more closely.
This commit modifies the usage() function to only print the -v option help
text when MICROPY_DEBUG_PRINTERS is enabled. The -v option requires this
build option to be enabled for it to have any effect.
The usage text is also modified to show the -i and -m options, and also
show that running a command, module or file are mutually exclusive.
This adds support for a MICROPYINSPECT environment variable that works
exactly like PYTHONINSPECT; per CPython docs:
If this is set to a non-empty string it is equivalent to specifying the
-i option.
This variable can also be modified by Python code using os.environ to
force inspect mode on program termination.
Zephyr removed the build target syscall_macros_h_target in commit
f4adf107f31674eb20881531900ff092cc40c07f. Removes reference from
MicroPython to fix build errors in the zephyr port.
This change is not compatible with zephyr v2.1 or earlier. It will be
compatible with Zephyr v2.2 when released.
The SYS_CLOCK_HW_CYCLES_TO_NS macro was deprecated in zephyr commit
8892406c1de21bd5de5877f39099e3663a5f3af1. This commit updates MicroPython
to use the new k_cyc_to_ns_floor64 api and fix build warnings in the zephyr
port.
This change is compatible with Zephyr v2.1 and later.
Zephyr restructured its includes in v2.0 and removed compatibility shims
after two releases in commit 1342dadc365ee22199e51779185899ddf7478686.
Updates include paths in MicroPython accordingly to fix build errors in
the zephyr port.
These changes are compatible with Zephyr v2.0 and later.
The backlight enable is active low on our board so the driver doesn't like it.
Toggling to GPIO manually for now.
As fixed the improper SPI bus pins definitions and it works!
Signed-off-by: Michael Welling <mwelling@ieee.org>
When stdout is redirected it is useful to have errors printed to stderr
instead of being redirected.
mp_stderr_print() can't be used in these two instances since the
MicroPython runtime is not running so we use fprintf(stderr) instead.
The ability to change the host is a frequently requested feature, so
explicitly document how it can be achieved using the existing code.
See issues #2121, #4385, #4622, #5122, #5536.
This commit improves pllvalues.py to generate PLL values for H7 MCUs that
are valid (VCO in and out are in range) and extend for the entire range of
SYSCLK values up to 400MHz (up to 480MHz is currently unsupported).
This board now has the following 3 build configurations:
- mboot + external QSPI in XIP mode + internal filesystem
- mboot + external QSPI with filesystem (the default)
- no mboot + external QSPI with filesystem
With a SPI flash that has more than 16MB, 32-bit addressing is required
rather than the standard 24-bit. This commit adds support for 32-bit
addressing so that the SPI flash commands (read/write/erase) are selected
automatically depending on the size of the address being used at each
operation.
This modifies the signature of mp_thread_set_state() to use
mp_state_thread_t* instead of void*. This matches the return type of
mp_thread_get_state(), which returns the same value.
`struct _mp_state_thread_t;` had to be moved before
`#include <mpthreadport.h>` since the stm32 port uses it in its
mpthreadport.h file.
PLLM is shared among all PLL blocks on F7 MCUs, and this calculation to
configure PLLSAI to have 48MHz on the P output previously assumed that PLLM
is equal to HSE (eg PLLM=25 for HSE=25MHz). This commit relaxes this
assumption to allow other values of PLLM.
With the previous change, stereo mp3 playback changed from needing
4 2304-byte allocations to needing 2 4604-byte allocations. This was
enough to cause MemoryErrors with regularity.
By using m_realloc() here, the existing memory region can be used.
m_realloc() also works on the first invocation, because m_realloc(NULL, sz)
just calls m_malloc of sz.
.. the documentation doesn't make this clear, but in practice it works
to write both of the DATABUF registers at the same time. This should
also reduce the amount of wear and tear DMA puts on the system, as the
number of transfers is cut in half. (the number of bytes transferred
remains the same, though)
In principle, this could cover all stereo cases if audio_dma_convert_signed
also learned to 16-bit extend and swap values. However, this is the
case that matters for stereo mp3 playback on PyGamer.
Testing performed: Listened to some tracks with good stereo separation.
It is not safe to enable MICROPY_ASYNC_KBD_INTR and MICROPY_PY_THREAD_GIL
at the same time. This will trigger a compiler error to ensure that it
is not possible to make this mistake.
Addition of GIL EXIT/ENTER pairs are:
- modos: release the GIL during system calls. CPython does this as well.
- moduselect: release the GIL during the poll() syscall. This call can be
blocking, so it is important to allow other threads to run at this time.
- modusocket: release the GIL during system calls. Many of these calls can
be blocking, so it is important to allow other threads to run.
- unix_mphal: release the GIL during the read and write syscalls in
mp_hal_stdin_rx_chr and mp_hal_stdout_tx_strn. If we don't do this
threads are blocked when the REPL or the builtin input function are used.
- file, main, mpconfigport.h: release GIL during syscalls in built-in
functions that could block.
When CFLAGS_EXTRA/LDFLAGS_EXTRA (or anything) is set on the command line of
a make invocation then it will completely override any setting or appending
of these variables in the makefile(s). This means builds like the coverage
variant will have their mpconfigvariant.mk settings overridden. Fix this
by using CFLAGS/LDFLAGS exclusively in the makefile(s), reserving the
CFLAGS_EXTRA/LDFLAGS_EXTRA variables for external command-line use only.
Translate common Ctrl-Left/Right/Delete/Backspace to the EMACS-style
sequences (i.e. Alt key based) for forward-word, backward-word, forwad-kill
and backward-kill. Requires MICROPY_REPL_EMACS_WORDS_MOVE to be defined so
the readline implementation interprets these.
Introduces a way to place CircuitPython code and data into
tightly coupled memory (TCM) which is accessible by the CPU in a
single cycle. It also frees up room in the corresponding cache for
intermittent data. Loading from external flash is slow!
The data cache is also now enabled.
Adds support for the iMX RT 1021 chip. Adds three new boards:
* iMX RT 1020 EVK
* iMX RT 1060 EVK
* Teensy 4.0
Related to #2492, #2472 and #2477. Fixes#2475.
