Flash erase/program functions disable the XIP bit. If any code runs from
flash at the same time (eg an IRQ or code it calls) it will fail and cause
a lockup.
this is only tested to come up to the REPL & mount CIRCUITPY. Pin
assignments should be right but were not double-checked. The screen
is unsupported so far.
This board depends on the I/O pull ups for the I2C bus (verified by
schematic) so this adds a compile time option that enables pull ups
for ANY i2c bus on a board.
The old way mapped each byte of nvm onto a distinct nvs key, but this
allowed storage of only a very small number of bytes out of the
theoretical capacity.
Reworked like this, about half of the nvs capacity can be used for
nvm, so you're guaranteed the ability to store 9kB this way.
This keeps the mutex info in the same spot in memory. "Statically
allocating it" with CircuitPython meant that the buffer moved when
the I2C object is moved to keep it alive for a display.
Fixes#4962
I noticed that the loop over 65535 possible denominators took a long time,
causing up to 100ms wait for a sound sample to start playing!
This algorithm, adapted from an algorithm shown in Python's fractions.py,
is guaranteed to find the best denominator in a small number of steps
(I think log2-many steps but I'm not sure). In practice, it means the time
between samples playing is just 10ms, and some of that is recreating the
sine wave sample in Python each time.
It often finds the same solution as the old code, but sometimes it finds
one a bit better since it compares the ratios using float point instead
of integer arithmetic.
The frequency divisor is limited to 255, which gives 48MHz/2/255 ~= 94.1kHz as
the lowest speed.
Without this change, values below this cut-off gave higher frequencies instead,
which didn't appear to have any relation to the frequency value requested.
Closes: #4883
There is a race between when we run background tasks and when we
sleep. If an interrupt happens between the two, then we may delay
executing the background task. On some ports we checked this for
TinyUSB already. On iMX RT, we didn't which caused USB issues.
This PR makes it more generic for all background tasks including
USB.
Fixes#5086 and maybe others.
This compiler is unable to optimise out the giant strcmp match generated
by MP_MATCH_COMPRESSED.
See github.com/micropython/micropython/pull/7659#issuecomment-899479793
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows the write to trigger a notification or indication, but only to
subscribed clients. This is different to gatts_notify/gatts_indicate,
which will unconditionally notify/indicate.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This implements (most of) the PEP-498 spec for f-strings and is based on
https://github.com/micropython/micropython/pull/4998 by @klardotsh.
It is implemented in the lexer as a syntax translation to `str.format`:
f"{a}" --> "{}".format(a)
It also supports:
f"{a=}" --> "a={}".format(a)
This is done by extracting the arguments into a temporary vstr buffer,
then after the string has been tokenized, the lexer input queue is saved
and the contents of the temporary vstr buffer are injected into the lexer
instead.
There are four main limitations:
- raw f-strings (`fr` or `rf` prefixes) are not supported and will raise
`SyntaxError: raw f-strings are not supported`.
- literal concatenation of f-strings with adjacent strings will fail
"{}" f"{a}" --> "{}{}".format(a) (str.format will incorrectly use
the braces from the non-f-string)
f"{a}" f"{a}" --> "{}".format(a) "{}".format(a) (cannot concatenate)
- PEP-498 requires the full parser to understand the interpolated
argument, however because this entirely runs in the lexer it cannot
resolve nested braces in expressions like
f"{'}'}"
- The !r, !s, and !a conversions are not supported.
Includes tests and cpydiffs.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This leaves much more space on SAMD21 builds that aren't "full builds".
These are new APIs that we don't need to add to old boards.
Also, tweak two Arduino boards to save space on them.
The EVSYS is used to generate an interrupt from the event. This
simplifies timing used in pulseio that conflicted with the
auto-reload countdown.
Fixes#3890
This commit creates a new stm32 board for the NUCLEO_H743ZI2, which is the
current version of this from ST. This is a modified copy of the
NUCLEO_H743ZI board, and the ZI2 board differs in a few minor ways:
- LED2 has moved from PB7 to PE1 and is now yellow rather than blue
- the USB power enable has moved from PG6 to PG10
- the USER button is now pulled down
RP2040 and SAMD51:
- Detect when DMA has finished, and stop DMA audio explicitly.
- Do not accidentally reuse `first_buffer` supplied by WaveFile or RawSample. Always realloc `first_buffer` and `second_buffer`
RP2040:
- When audio playing is stopped, write a final zero to the output register. This prevents residual PWM tones.
- Handle buffer size for 8-bit samples properly for 16-bit output.
- Fail on some edge cases (which may not be possible at the moment).
This function can be used to enable and disable the DC/DC converter with or
without the Bluetooth stack enabled. It can also be used to query the
current state of the DC/DC.
This commit also adds a definition of ARRAY_SIZE needed by nrfx HAL-layer.
extmod/vfs_lfs.c needs to resolve `mp_hal_time_ns()` in order to calculate
a timestamp from 1970 epoch. A wall clock is not available in the nrf
port, hence the function is implemented to resolve compilation linkage
error. The function always return 0.
Set the default manifest to "modules/manifest.py". This includes files
from the folder "modules/scripts". The manifest default value is overriden
by all nrf51 boards that have SoftDevice present (SD=s110) to save flash.
Also add "modules/manifest.py" which is set to freeze
"modules/scripts/_mkfs.py".
Add a helper script _mkfs.py which automatically formats the file system if
nrf.Flash() is located and a VFS file system has been included in the
compilation.
The precedence is: first LFS1, LFS2 then FAT.
Update the Makefile to handle FROZEN_MANIFEST, and the README with some
small samples on how to use freeze manifests. And add BOARD_DIR to the
Makefile which can be referenced in boards/<board>/mpconfigboard.mk to
include a board specific manifest.
Enable the following features for all boards except
nrf51 boards with SoftDevice present:
- MICROPY_VFS
- MICROPY_PY_NRF
- MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
Add posibility to override linker script "_fs_size" from make by adding the
FS_SIZE parameter. The syntax of value is linker script syntax. For
example, the value of 131072 bytes can be written as 128K like this:
FS_SIZE=128K.
If not set, default value for "_fs_size" from linker script will be used.
Disable MICROPY_FATFS_MULTI_PARTITION configuration because there is no
partition table in the flash for FATFS to read.
Also, set MICROPY_FATFS_MAX_SS to the size of a flash page. For nrf51 the
value 1024 is set. For nrf52/nrf91 the value 4096 is set.
This documents parameters that can be passed to make to enable a specific
file system to included in the build. Also, document the Makefile override
parameter "FS_SIZE" that can be used to tune the size of the flash region
to use as internal flash file system.
Update flash.c to also be compiled in when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled and SoftDevice is
present.
Update bluetooth/ble_drv.c to forward flash events to flash.c when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled.
This commit adds the "nrf" module for port specific modules and objects.
Included in it is the "Flash" object which exposes a block device
implementation to access internal SoC flash.
Thanks to @aykevl aka Ayke van Laethem for the initial implementation.
Calculate the unused flash area on the target device. The values will be
exposed by _unused_flash_start and _unused_flash_length. The start address
and the length are not aligned to either word or pages.
This allows changing the frequency to: 100kHz, 200kHz, 400kHz, 800kHz,
1MHz, 2MHz, 4MHz, 8MHz, 16MHz, 32MHz, 64MHz. For frequencies 2MHz and
below, low power run (LPR) mode is enabled automatically.
Signed-off-by: Damien George <damien@micropython.org>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Reverse operations are supported on stm32 and rp2, and esp32 has enough
space to also enable inplace operations, to make it complete.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This enables optional support for the hardware UART to use the RTS and/or
CTS pins for flow control.
The new "flow" constructor keyword specifies a bitmask of RTS and/or CTS.
This matches the interface used by machine.UART on stm32 and rp2.
Previously on ESP32 it was possible to specify which pins to use for the
RTS and CTS signals, but hardware flow control was never functional: CTS
was not checked before transmitting bytes, and RTS was always driven high
(signalling no buffer space available). With this patch, CTS and RTS both
operate as expected.
This also includes an update to the machine.UART documentation.
Signed-off-by: Will Sowerbutts <will@sowerbutts.com>
The QR decoder has a single item that is 8908 bytes big and placed
on the stack. (struct datastream)
Without enlarging the stack, this will reliably crash.
Call `supervisor.disable_ble_workflow()` and the BLE workflow will
be disabled until the chip is reset.
This also includes a couple fixes:
1. Terminals can now be deinit by setting the tilegrid to NULL. This
prevents using the tilegrid before display is init.
2. Fix BLE serial send amount when sending more than a single packet.
Fixes#5049
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.
This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
hyperflash.
- minor incidental changes to other boards so they still build
Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
On ESP ctrl-c during fake sleep will now stop the sleep. A crash
on real deep sleep is now fixed as well. (Exception string saving
was crashing on reading the deep sleep exception.) Fixes#4010
This also fixes nRF fake sleep after the first time. The internal
variable wasn't being reset early enough. Fixes#4869
Passing in a PWMOut still works but is deprecated. It will be
removed in CircuitPython 8.0.0
This also switches STM32 timer indices and channel indices to
0-based in our pin data rather than `- 1` everywhere. The latter is
more bug prone.
Most of the way for #3264
Tested on Metro M0, Metro M4, Feather S2, Feather nRF52840, Feather
STM32F4 and Arduino RP2040.
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, if the UART hardware FIFO had a few chars but still
below the FIFO trigger threshold, and the ringbuf was empty, the read
function would timeout if timeout==0 (the default timeout).
This fix follows the suggestion of @iabdalkader.
The RX IRQ does not trigger if the FIFO is less than the trigger level, in
which case characters may be available in the FIFO, yet not in the ringbuf,
and the ioctl returns false.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
For RP2040 boards, we now change the default flash size based on
the configured flash. We will still try to read the size from the
flash first.
Fixes#4874
This helps the OS switch to and give other threads processing time during
the sleep. It also ensures that pending events are handled, even when
sleeping for 0ms.
Fixes issue #5344.
Signed-off-by: Damien George <damien@micropython.org>
Call MICROPY_EVENT_POLL_HOOK even on very short delays so that busy loops
that call sleep_ms still yield to events and other threads.
See related issue #5344.
After the script stops with the exception thrown the final gc_sweep
will call any finalizers and they usually call deinit. deinit on
invalid objects can wreak havoc by changing random memory or
(hopefully) crashing. This fixes ensures the object is deinited
until initialization succeeds and the object is valid.
Do the same fix for I2C and SPI too.
Fixes#4700 and fixes#5005
Replace "master" with "controller" and "slave" with "peripheral" in
comments, errors, and debug messages.
Add CONTROLLER and PERIPHERAL constants to pyb.SPI and pyb.I2C classes;
retain MASTER and SLAVE constants for backward compatiblity.
Using a 2-item transaction queue instead of 1 allows long transfers to
be executed with the minimum inter-transaction delay. Limit maximum
transaction length to ensure an integer multiple of the SPI `bits`
setting are transferred. Fixes#7511.
MicroPython implements some 3.5+ features, and this change helps to reduce
the need for some .exp files in the test suite.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
As the CircuitPython grows, it may at some point no longer be possible
to squeeze it on some of the flash-less SAMD21 boards, so it would be
good to have the option of shrinking the filesystem size on per-board
basis. This change allows to define CIRCUITPY_INTERNAL_FLASH_FILESYSTEM_SIZE
inside the board's mpconfigborard.h file.
1. Check for correct error values from dma_claim_unused_channel.
2. Introduce a .stereo flag for simplicity.
3. Clarify PWM carrier frequency choice.
4. Start introducing quiescent audio value. Still need to ramp up/down.
5. Redo audio stop logic a bit.
6. Fix (unrelated) displayio dependency things.
There is still an interference problem between other DMA users and audio. Still debugging this.
Adds support for hardware SPI to the zephyr port. Consistent with other
ports, such as rp2 and stm32, we only implement the SPI protocol functions
(init and transfer). Explicit sck/mosi/miso selection is not supported
and new SPI instances are initialized with default values.
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
These warnings appear with GCC 11. Keep them as warnings but not as
compiler errors so they can be dealt with properly in the future.
Signed-off-by: Damien George <damien@micropython.org>
The ADC_FIRST_GPIO_CHANNEL and ADC_LAST_GPIO_CHANNEL macros are no longer
needed. Instead the pin_adcX table (X = 1, 2, 3) is now generated to be
the exact size needed for a given MCU, and MP_ARRAY_SIZE(pin_adcX) is used
to determine the upper bound.
This commit also allows CPU pins to be excluded from ADC configuration if
they are hidden by prefixing their name with a "-".
Signed-off-by: Damien George <damien@micropython.org>
* Modify common functions in adc.c to accept ADC handle.
* Most external channels are connected to ADC12 which is used by default.
* For ADCAll (internal channels) ADC3 is used instead.
* Issue #4435 is possibly related (at least partially fixed).
This change allows specification of the idle level and TX carrier output
level (through changed initialisation API), and more flexible specification
of pulses for write_pulses.
This is a breaking change for the esp32.RMT constructor API. Previous code
of this form:
esp32.RMT(..., carrier_duty_percent=D, carrier_freq=F)
will now raise an exception and should be changed to:
esp32.RMT(..., tx_carrier=(F, D, 1))
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.
The Makefile had to be changed in order to build the .bin file as well.
This adds a call to mp_deinit() in the main function of the STM32 port.
This enables the use of MICROPY_PORT_DEINIT_FUNC on that port, as well as
cleaning up the GIL if threading is enabled.
Previous behaviour was: if boot.py had an exception then main.py would
still run, which is arguably unexpected behaviour.
This commit changes the behaviour so main.py is not run if boot.py has an
error.
Signed-off-by: Damien George <damien@micropython.org>
Since the new keypad module is taking over gamepad functionality,
I'm switching to it. If this works well, I will make the change
for the remaining boards.
This avoids the irritation of the PJRC HalfKay loader on Teensy 4.0. Block
0 and 1 are properly erased and the additional formatting in the make
script is not required anymore.
This class supports SPI bus controller mode, with blocking transfers.
SPI device numbers start at 0, to comply with the pinout of the Teensy
boards. With the configured clock frequency the fastest baud rate is
33MHz. For messages longer 16 bytes DMA is used. The class uses the
existing framework with extmod/machine_spi.c.
Extended driver options:
- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
Since the pins used by the SPI are fixed, no Pin settings can be made.
Thus the drive option is added allowing to control ringing and crosstalk
on the connection.
- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
Default is 2 clock cycles.
When looping, now disable the TX interrupt after calling rmt_write_items()
function to handle change in IDF behaviour (since v4.1). Also check length
of pulses to ensure it fits hardware limit.
Fixes issue #7403.
The GC now works correctly using asyncify and the functions
emscripten_scan_stack() and emscripten_scan_registers(). Stack/call depth
is monitored via the use of the pystack option.
Fixes issue #6738.
Signed-off-by: Damien George <damien@micropython.org>
Calculating the weekday each time you want to set a date is error prone and
tiresome. MicroPython can do it on its own - hardware on some ports do not
support storing weekday in hardware and always computes it on the fly,
ignoring the value given to the constructor.
During discussion for #7432 the conclusion was that there seems to be no
obvious reason to let user set the weekday to an incorrect value so it
makes sense to just ignore the provided weekday value and always compute
the correct value. This patch introduces this change for the rp2 port.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
The RTC in rp2 can store any, even wrong, number as a weekday in RTC. It
was, however, discussed in #7394 that we would like to unify all ports and
use 0 as Monday, not Sunday in the machine.RTC implementation.
This patch makes sure that the default date set in RTC is adheres to this
convention. It also fixes the example in quickref to use proper weekday to
avoid confusion.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
nRF CircuitPython boards will now provide the file transfer
service defined here: https://github.com/adafruit/Adafruit_CircuitPython_BLE_File_Transfer
USB capable boards will only advertise if previously bonded to a
device or if the reset button is pressed during the fast blue
flashes on start up. When pressed, the board will restart again but
the blue period will not flash.
Boards without USB will always advertise.
When previously bonded, the advertisement is private so that no
other peers can connect. If advertising publicly, the tx power is
lowered to reduce the likelihood of bonding from a distance.
This PR also fixes issues with loading identities of bonded peers
so that our address can now be resolved and we can resolve others'
addresses when scanning.
Add an optional 'lock' kwarg to callback that locks GC and scheduler. This
allows the callback to be invoked asynchronously in 'interrupt context',
for example as a signal handler.
Also add the 'cfun' member function to callback, that allows retrieving the
C callback function address. This is needed when the callback should be
set to a struct field.
See related #7373.
Signed-off-by: Amir Gonnen <amirgonnen@gmail.com>
It reschedules the BT HCI poll soft timer so that it is called exactly when
the next timer expires.
Signed-off-by: Damien George <damien@micropython.org>
Instead of using systick the BT subsystem is now scheduled using a soft
timer. This means it is scheduled only when it is enabled.
Signed-off-by: Damien George <damien@micropython.org>
And call mp_pairheap_init_node() in soft_timer_static_init() so that
reinsert can be called after static_init.
Signed-off-by: Damien George <damien@micropython.org>
Dynamically generate/loaded native code (eg from @micropython.native or
native .mpy files) needs to be able allocate from IRAM, and the memory
protection feature must be disabled for that to work. Disabling it is
needed to get native code working on ESP32-S2 and -C3.
Signed-off-by: Damien George <damien@micropython.org>
This introduces a new macro to get the main thread and uses it to ensure
that asynchronous exceptions such as KeyboardInterrupt (CTRL+C) are only
scheduled on the main thread. This is more deterministic than being
scheduled on a random thread and is more in line with CPython that only
allow signal handlers to run on the main thread.
Fixes issue #7026.
Signed-off-by: David Lechner <david@pybricks.com>
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
Commit 0abf6f830c removed _boot.py from the
manifest for the GENERIC_512K board because the build does not include a
filesystem. But the main code expects _boot.py to be there and prints an
error if it's not. So add a custom _boot.py, which just sets the
gc.threshold().
Signed-off-by: Damien George <damien@micropython.org>
This adds a wlan.config(reconnects=N) option to set the number of reconnect
attempts that will be made if the WLAN connection goes down. The default
is N=-1 (infinite retries, current behavior). Setting
wlan.config(reconnects=0) will disable the reconnect attempts.
A nice side effect of reconnects=0 is that wlan.status() will report the
disconnect reason now. See related issue #5326.
Ethernet-PHYs from ESP-IDF (LAN8720, IP101, RTL8201, DP83848) are now
supported in IDF v4.1 and above. PHY_KSZ8041 is only for ESP-IDF 4.3 and
above. ESP32S2 is not supported.
Signed-off-by: Tobias Eydam <eydam-prototyping@outlook.com>
The implementation uses the LPUARTx devices. Up to 8 UARTs can be used,
given that the pins are accessible. E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.
For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1. All other UART are assigned to different Pins:
MIMXRT1010-EVK:
D0/D1 UART 1
D6/D7 UART 2
A0/D4 UART 3
MIMXRT1020-EVK:
D0/D1 UART 1
D6/D9 UART 2
D10/D12 UART 3
D14/D15 UART 4
A0/A1 UART 5
MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
D0/D1 UART 1
D7/D6 UART 2
D8/D9 UART 3
A1/A0 UART 4
This fixes error: cast to smaller integer type 'int' from 'pthread_t'.
pthread_t is defined as long, not as int.
Signed-off-by: Pavol Rusnak <pavol@rusnak.io>
The rtc_set_datetime() from pico-sdk will validate the values in the
datetime_t structure and refuse to set the time if they aren't valid. It
makes sense to raise an exception if this happens instead of failing
silently which might be confusing (as an example, see:
https://github.com/micropython/micropython/pull/6928#issuecomment-860166044
).
The supplied value for microseconds in datetime() will be treated as a
starting value for the reported microseconds. Due to internal processing
in setting the time, there is an offset about 1 ms.
This change moves the datetime tuple format back to the one used by all the
other ports:
(year, month, day, weekday, hour, minute, second, microsecond)
Weekday is a number between 0 and 6, with 0 assigned to Monday. It has to
be provided when setting the RTC with datetime(), but will be ignored on
entry and calculated when needed.
The weekday() method was removed, since that is now again a part of the
datetime tuple.
The now() method was updated so it continues to return a tuple that matches
CPython's datetime module.
Initial support for machine.RTC on rp2 port. It only supports datetime()
method and nothing else. The method gets/returns a tuple of 8 items, just
like esp32 port, for example, but the usec parameter is ignored as the RP2
RTC only works up to seconds precision.
The Pico RTC isn't very useful as the time is lost during reset and there
seems to be no way to easily power up just the RTC clock with a low current
voltage, but still there seems to be use-cases for that, see issues #6831,
and a Thonny issue #1592. It was also requested for inclusion on v1.15
roadmap on #6832.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Changes introduced are:
- the application offset is now loaded from the partition table instead of
being hard-coded to 0x10000
- maximum size of all sections is computed using the partition table
- an error is generated if any section overflows its allocated space
- remaining bytes are printed for each section
Signed-off-by: Damien George <damien@micropython.org>
`idf.py monitor` connects to the debug UART and shows the messages. In
contrast to a traditional terminal program, it also has the limited
ability to transform hex addresses into file & line number information,
especially for debug builds.
This requires the elf file be copied to a specific place.
.. this board is nearly the same as the "1.2" version originally
released, but makes a few changes to reduce pin conflicts between the 13-pin
camera header and the bootstrapping pins. "1.3" was introduced in summer
2020-- check the bottom of your board silk to find out whether you have a 1.2
or a 1.3, because it's not clear whether there is remaining 1.2 stock.
Another vexing fact about the 1.3 is that its LCD can have one of two
chipets, and the chipset used is not marked anywhere!
This commit adds a few math functions to the source list in the Makefile,
and implements the log2f function, so that ulab can be compiled on the nrf
boards. It also addresses part of #5162.
This commit fixes the following problems converting to/from Python integers
and ffi types:
- integers of 8 and 16 bits not working on big endian
- integers of 64 bits not working on 32 bits architectures
- unsigned returns were converted to signed Python integers
Fixes issue #7269.
Currently only advertising and scanning are supported, using the ring
buffer for events (ie not synchronous events at this stage).
The ble_gap_advertise.py multi-test passes (tested on a nucleo_wb55rg
board).
Signed-off-by: Damien George <damien@micropython.org>
Zephyr's default value for CONFIG_NET_SOCKETS_POSIX_NAMES was changed
from false to true between Zephyr v2.5.0 and v2.6.0. This caused
conflicts in MicroPython, which uses the zsock_ prefixed functions, so
disable it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Zephyr's Kconfig symbols and defaults for SDHC/SDMMC disk drivers and
the disk access subsystem were reworked between Zephyr v2.5.0 and
v2.6.0. Update MicroPython accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Take changes from https://github.com/micropython/micropython/pull/3694
(expected to be merged soon) as well as other accumulated stuff from
upstream that we want.
Leave our desired differences, including:
* silencing warnings in python3
* renaming the file descriptors returned by openpty()
* adding ulab tests
* Adding "." to the import path for skip_if
This speeds up `make test_full` and should also reduce the time in CI
a little bit.
Initial version, using the LP RTC clock. It provides setting the date and
time with rtc.init() or rtc.datetime(), and reading the date and time with
rtc.datetime() or rtc.now(). The method weekday() reports the weekday of
the current date. It starts with 0 for Monday.
The tuple order for datetime() and now() matches the CPython sequence:
(year, month, day, hour, minute, second, microsecond, TZ). TZ is ignored
and reported as None. Microsecond is provided at a best effort.
If a battery is not supplied, the default boot date/time is 1970/1/1 0:0:0.
With a battery, the clock continues to run even when the board is not
powered. The clock is quite precise. If not, using rtc.calibration() may
help.
It supports three hardware timer channels based on the PIT timers of the
MIMXRT MCU. The timer id's are 0, 1 and 2. On soft reboot all active
timers will be stopped via finalisers.
This is required since the Teensy Halfkay loader attempts to erase all of
the flash but fails to do so, at least in my tests. Formatting brings it
back to a known state.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.
Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS. VFS
will take up most of the available flash. 1M is reserved for code. 9K is
reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c. All flashing
related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
module.
It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.
Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
Adds support for NeoPixels on GPIO32 and GPIO33 on ESP32. Otherwise,
NeoPixels wired to GPIO32/33 wll silently fail without any hints to the
user.
With thanks to @robert-hh.
Fixes issue #7221.
ATOM is a very small ESP32 development board produced by M5Stack, with a
size of 24mm * 24mm, with peripherals such as WS2812, IR, button, MPU6886
(Only Matrix), and 8 GPIO extensions. It also has a plastic shell.
This configuration is used by @ladyada and more often than it should
we've discovered late that a change introduced problems building
there.
By adding this to regular CI, hopefully we learn about and fix these
issues sooner rather than later.
With GCC 11 there is now a warning about array bounds of OTP-mac, due to
the OTP being a literal address.
Signed-off-by: Damien George <damien@micropython.org>
The 512k build does not have a filesystem so there is no reason to include
the filesystem-related modules. This commit provides a custom manifest.py
for this board which no longer includes: _boot.py, flashbdev.py,
inisetup.py, upip.py, upip_utarfile.py. This cuts the build down by about
9k of flash.
Signed-off-by: Damien George <damien@micropython.org>
This is more or less a complete re-organization of the code.
* Use the actual byte size of the .bin file as the flash size,
as the algorithm for packing sections into the flash is complicated
* Match each section to a data region & find the high water mark in the
region
* Report on all the RAM regions, separately
Note that elftools is a requirement of esp-idf and so does not need to
be listed in our requirements.txt.
- modified pin type from pin_obj_t to machine_pin_obj_t
- created machine_pin.c
- implemented basic version of make-pins.py to genertate pins.c/.h files
automatically; the only alternate function currently supported is GPIO
- added af.csv files for all supported MCUs
- replaced pins.c/pins.h files with pin.csv for all boards
- implemented on/off/high/low/value/init methods
- Implemented IN/OUT/OPEN_DRAIN modes
- modified LDFLAGS for DEBUG build to get usefull .elf file for debugging
Signed-off-by: Philipp Ebensberger
Re-commiting to fix local GitHub config issues. Adding CircuitPython support for the Arduino Nano RP2040 Connect. Have tested all digital and analog I/O, I2C, onboard LSM6DSOX. Uses the AT25SF128A external flash.
Leaving the bootloader from an IRQ (eg USB or I2C IRQ) will not work if
MBOOT_LEAVE_BOOTLOADER_VIA_RESET is disabled, ie if mboot jumps directly to
the application. This is because the CPU will still be in IRQ state when
the application starts and IRQs of lower priority will be blocked.
Fix this by setting a flag when the bootloader should finish, and exit the
bootloader always from the main (top level) thread.
This also improves the USB behaviour of mboot: it no longer abruptly
disconnects when the manifest command is sent.
Signed-off-by: Damien George <damien@micropython.org>
RX and CTS are the input pins and pull-ups are enabled so they don't cause
a problem if left unconnected. But the output pins don't need a pull up
(they were originally all configured with pull up in commit
8f7491a109).
If needed, the pull-ups can be disabled in Python using machine.Pin after
the UART is constructed.
See issue #4369.
Signed-off-by: Damien George <damien@micropython.org>
The DMA driver will turn off DMA if it hasn't been used for an amount of
time (to save power). The SDIO driver for cyw43 WLAN was not informing the
DMA driver that it was using DMA and there was a chance that the DMA would
turn off in the middle of an SDIO DMA transfer. The symptoms of this would
be printing of SDIO error messages and a failure to communicate with the
cyw43 WLAN module.
This commit fixes this issue by changing the SDIO driver to use the
dma_nohal_XXX API to initialise and start the DMA.
Signed-off-by: Damien George <damien@micropython.org>
SysTick cannot wake the CPU from WFI/WFE so a hardware timer is needed to
keep track of ticks/delay (similar to the nrf port).
Fixes issue #7234.
Signed-off-by: Damien George <damien@micropython.org>
This detects an overflowed flash partition, such as
```
1452105 bytes used, -10313 bytes free in flash firmware space out of 1441792 bytes (1408.0kB).
444428 bytes used, 1652724 bytes free in ram for stack and heap out of 2097152 bytes (2048.0kB).
```
on a metro esp32-s2 built with debugging.
This also removes the need to pin share because we don't use the
status LED while user code is running.
The status flashes fallback to the HW_STATUS LED if no RGB LED is
present. Each status has a unique blink pattern as well.
One caveat is the REPL state. In order to not pin share, we set the
RGB color once. PWM and single color will be shutoff immediately but
DotStars and NeoPixels will hold the color until the user overrides
it.
Fixes#4133
A board can now customise mboot with:
- MBOOT_LED1, MBOOT_LED2, MBOOT_LED3, MBOOT_LED4: if it needs to have
different LEDs for mboot compared to the application
- MBOOT_BOARD_LED_INIT: if it needs a fully customised LED init function
- MBOOT_BOARD_LED_STATE: if it needs a fully customised LED state-setting
function
- MBOOT_BOARD_GET_RESET_MODE: if it needs a fully customised function to
get the reset mode
With full customisation, the only requirement is a single LED to show the
status of the bootloader (idle, erasing, flashing, etc), which can be
configured to do nothing if needed.
Signed-off-by: Damien George <damien@micropython.org>
It is enabled by default to get the standard behaviour of doing a reset
after it is finished, but can be disabled by a board to jump straight to
the application (likely the board needs to use MBOOT_BOARD_CLEANUP to make
this work).
The application is passed a reset mode of BOARDCTRL_RESET_MODE_BOOTLOADER
if the bootloader was active and entered via a jump.
Signed-off-by: Damien George <damien@micropython.org>
This new logic is equivalent to the old logic when the only possibilities
for reset_mode are NORMAL, SAFE_MODE and FILESYSTEM, which is the standard
case. But the new logic also allows other reset_mode values (eg
BOOTLOADER) to run boot.py and main.py.
Signed-off-by: Damien George <damien@micropython.org>
When disabled the bootloader is entered via a direct jump. When enabled
the bootloader is entered via a system reset then a jump. It's enabled by
default to retain the existing behaviour, which is the recommended way.
Signed-off-by: Damien George <damien@micropython.org>
Improvements made:
- PSRAM support for S2
- partition definition for 16MiB flash
- correct ADC and DAC pins
- correct GPIO and IRQ pins
- S3 components in CMakeLists
Based on original commit made by Seon Rozenblum aka @UnexpectedMaker.
Signed-off-by: Damien George <damien@micropython.org>
Any code running on core1 should be stopped on soft-reset (the GC heap is
reset so if code continues to run on core1 it will see corrupt memory).
Signed-off-by: Damien George <damien@micropython.org>
So a lock can be acquired on one Python thread and then released on
another. A test for this is added.
Signed-off-by: Damien George <damien@micropython.org>
Because vPortCleanUpTCB runs on the FreeRTOS idle task and cannot execute
any VM or runtime related code like freeing memory.
Signed-off-by: Damien George <damien@micropython.org>
This fixes a bug where double arguments on a 32-bit architecture would not
be passed correctly because they only had 4 bytes of storage (not 8). It
also fixes a compiler warning/error in return_ffi_value on certian
architectures: array subscript 'double[0]' is partly outside array bounds
of 'ffi_arg[1]' {aka 'long unsigned int[1]'}.
Fixes issue #7064.
Signed-off-by: Damien George <damien@micropython.org>
As MicroDev1 pointed out the problem is a divide by zero when calculating the duty cycle.
Maybe need to check again in `common_hal_pwmio_pwmout_set_frequency()`.
FeatherS2 crashes if you set the PWMOut frequency to 0.
This change will raise `ValueError: Invalid PWM frequency` if the requested frequency is 0.
(Lifted from the atmel-samd port)
The number shown in the USB id is now the same as that returned by
machine.unique_id(). All 8 bytes are inserted as hex into the USB id. A
usb id at /dev/serial/by-id then looks like:
usb-MicroPython_Board_in_FS_mode_e469b03567342f37-if00
Doing "import <tab>" will now complete/list built-in modules.
Originally at adafruit#4548 and adafruit#4608
Signed-off-by: Artyom Skrobov <tyomitch@gmail.com>
After discussing with danh, I noticed that `a/**/b` would not match `a/b`.
After correcting this and re-running "pre-commit run --all", additional
files were reindented, including the codeformat script itself.
In #4683, tannewt noticed that uncrustify was not running on some
file in common-hal.
I investigated and found that it was not being run on a bunch of paths.
Rather than make incremental changes, I rewrote list_files to work
bsaed on regular expressions; these regular expressions are created from
the same git-style glob patterns.
I spot-checked some specific filenames after this change, and all looks good:
```
$ python3 tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup extmod/virtpin.c ports/raspberrypi/background.h ports/raspberrypi/common-hal/pulseio/PulseIn.c
black --fast --line-length=99 -v tests/thread/thread_exit1.py
```
recursiveloop and int_small are excluded, while PulseIn, virtpin,
and background are included.
Testing running from a subdirectory (not _specifically_ supported though):
```
(cd ports && python3 ../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c)
../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup ../extmod/virtpin.c raspberrypi/common-hal/pulseio/PulseIn.
```
As a side-effect, a bunch more files are re-formatted now. :-P
This fixes some missing and incorrectly-assigned pins for the SparkFun Thing Plus RP2040 protoboard so that they actually match what the board says. This also changes the default SPI pins from the SD card pins to the breakout pins on the side of the board.
This board does not work with CONFIG_NETWORKING enabled. And
CONFIG_CONSOLE_SUBSYS is enabled so that ctrl-C works.
Signed-off-by: Damien George <damien@micropython.org>
And ctrl-C can now interrupt a time.sleep call. This uses Zephyr's k_poll
API to wait efficiently for an event signal, and an optional semaphore.
Signed-off-by: Damien George <damien@micropython.org>
This helper is added to properly set a pending exception, to mirror
mp_sched_schedule(), which schedules a function.
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_ENABLE_SCHEDULER is enabled then MP_STATE_VM(sched_state) must
be updated after handling the pending exception, which is done by the
mp_handle_pending() function.
Signed-off-by: Damien George <damien@micropython.org>
This can now be selected by setting MICROPY_HW_SDIO_SDMMC, which defaults
to 1, ie SDMMC1. The pins can also be selected and default to the standard
C8/C9/C10/C11/C12/D2.
H7 compatibility problems in port.c and peripherals/exti
NRF build failures due to new use of const for PinAlarm pin objects
Isolated board flash overage on blackpill_with_flash, remove audio modules
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define MBOOT_TEXT0_ADDR to place mboot at a location other
than 0x08000000. This can be useful if, for example, there is already a
different bootloader on the device.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define MBOOT_LD_FILES (at the Makefile-level) to specify
custom linker scripts. And stm32_generic.ld has been split into 2 pieces
so one or the other can be reused (usually stm32_sections.ld wolud be
reused by a board, and stm32_memory.ld redefined).
Signed-off-by: Damien George <damien@micropython.org>
A board can now use BUILDING_MBOOT at the Makefile-level to do things
conditional on building mboot, for example add source files to SRC_C.
Signed-off-by: Damien George <damien@micropython.org>
Commit 1e297c8898 introduced a bug where the
very first reset-mode state on the LEDs was not shown, because prior to
that commit the first reset-mode state was the same as the initial LED
state (green on, others off) and update_reset_mode() was called after
setting this initial LED state.
This is fixed in this commit by changing the update_reset_mode() loop so
that it displays the current reset mode before doing the delay.
Signed-off-by: Damien George <damien@micropython.org>
And use the same boardctrl.h header for both the application and mboot so
these constants are consistent.
Signed-off-by: Damien George <damien@micropython.org>
This adds support for making static (ie not on the Python GC heap) soft
timers. This can be useful for a board to define a custom background
handler, or eventually for BLE/network processing to use instead of systick
slots; it will be more efficient using soft timer for this.
The main issue with using the existing code for static soft timers is that
it would combine heap allocated and statically allocated soft_timer_entry_t
instances in the same pairing-heap data structure. This would prevent the
GC from tracing some of the heap allocated entries (because the GC won't
follow pointers outside the heap).
This commit makes it so that soft timer entries are explicitly marked,
instead of relying on implicit marking by having the root of the pairing
heap in the root pointer section. Also, on soft reset only the heap-
allocated soft timers are deleted from the pairing heap, leaving the
statically allocated ones.
Signed-off-by: Damien George <damien@micropython.org>
This commit re-enables the command-line make option "FROZEN_MANIFEST". The
boards/*/mpconfigboard.cmake will now use the command-line FROZEN_MANIFEST
value if supplied.
Usage: make FROZEN_MANIFEST=~/foo/my-manifest.py
Unify USB-related makefile var and C def as CIRCUITPY_USB.
Always define it as 0 or 1, same as all other settings.
USB_AVAILABLE was conditionally defined in supervisor.mk,
but never actually used to #ifdef USB-related code.
Loosely related to #4546
Because "find_package(Python3 ...)" requires at least this version of
CMake. And other features like GREATER_EQUAL and COMMAND_EXPAND_LISTS need
at least CMake 3.7 and 3.8 respectively.
Signed-off-by: Damien George <damien@micropython.org>
Improvements are:
- Default period is 1000ms with callback disabled.
- if period is not specified then it's not updated (previously, if period
was not specified then it was set to -1 and running the timer callback as
fast as possible, making the REPL unresponsive).
- Use uint64_t to compute delta_ms, and raise a ValueError if the period is
too large.
- If callback is not specified then it's not updated.
- Specifying None for the callback will disable the timer.
Signed-off-by: Damien George <damien@micropython.org>
Added board definition for the Sparkfun MicroMod RP2040.
Mostly followed the format for pins from the MicroMod nRF52840 board
definition, as MicroMod tries to standardize pins across
microcontrollers.
The PIO state machines on the RP2040 have 4 word deep TX and RX FIFOs. If
you only need one direction, you can "merge" them into either a single 8
word deep TX or RX FIFO.
We simply add constants to the PIO object, and set the appropriate bits in
`shiftctrl`.
Resolves#6854.
Signed-off-by: Tim Radvan <tim@tjvr.org>
Commit 8a917ad252 added the gpio_reset_pin()
call to make sure that pins that were used as ADC inputs could subsequently
be used as digital IO. But calling gpio_reset_pin() will enable the
pull-up on the pin and so pull it high for a brief period. Instead use
rtc_gpio_deinit() which will just reconfigure the pin as a digital IO and
do nothing else.
Fixes issue #7079 (see also #5771).
Signed-off-by: Damien George <damien@micropython.org>
This is handy for remote characteristics because it allows for
the PacketBuffer binding code to have the correct max size. This
PR also adds checks so we don't write outside the outgoing buffer.
For an unconnected TCP socket, poll should return WR|HUP and read should
raise ENOTCONN. This is implemented by this commit and now the following
tests pass on esp32: extmod/usocket_tcp_basic.py,
net_hosted/connect_poll.py.
Signed-off-by: Damien George <damien@micropython.org>
This change allows running the tests in tests/basics/ without any failures
(but some tests are still skipped).
Signed-off-by: Damien George <damien@micropython.org>
This fixes `error: variable 'subpkg_tried' might be clobbered by 'longjmp'
or 'vfork' [-Werror=clobbered]` when compiling on ppc64le and aarch64 (and
possibly other architectures/toolchains).
This function includes the UART prescaler in the calculation (if it has
one, eg on H7 and WB MCUs).
Signed-off-by: Damien George <damien@micropython.org>
The STM32WB has a problem when address resolution is enabled: under certain
conditions the MCU can get into a state where it draws an additional 10mA
or so and eventually ends up with a broken BLE RX path in the silicon. A
simple way to reproduce this is to enable address resolution (which is the
default for NimBLE) and start the device advertising. If there is enough
BLE activity in the vicinity then the device will at some point enter the
bad state and, if left long enough, will have permanent BLE RX damage.
STMicroelectronics are aware of this issue. The only known workaround at
this stage is to not enable address resolution, which is implemented by
this commit.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, if C2 was busy (eg lots of BLE activity) then it may
not have had time to respond to the notification on the IPCC_CH_MM channel
by the time additional memory was available to put on that buffer. In such
a case C1 would modify the free buffer list while C2 was potentially
accessing it, and this would eventually lead to lost memory buffers (or a
corrupt linked list). If all buffers become lost then ACL packets
(asynchronous events) can no longer be delivered from C2 to C1.
This commit fixes this issue by waiting for C2 to indicate that it has
finished using the free buffer list.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
This change allows to build firmware for different rp2-based boards,
following how it is done in other ports like stm32 and esp32. So far only
the original Pico and Adafruit Feather RP2040 are added. Board names
should match (sans case) those in pico-sdk/src/boards/include/boards/.
Usage: Pico firmware can be build either using make as previously (it is
the default board) or by `make BOARD=PICO`. Feather is built by `make
BOARD=ADAFRUIT_FEATHER_RP2040`. Only the board name and flash drive size
is set, pin definition is taken from the appropriate pico-sdk board
definition. Firmware is saved in the directory build-BOARD_NAME.
Instantiation and init now support the rxbuf and txbuf keywords for setting
the buffer size. The default size is 256 bytes. The minimum and maximum
sizes are 32 and 32766 respectively.
uart.write() still includes checks for timeout, even if it is very unlikely
to happen due to a) lack of flow control support and b) the minimal timeout
values being longer than the time it needs to send a byte.
StateMachine.restart: Restarts the state machine
StateMachine.rx_fifo: Return the number of RX FIFO items, 0 if empty
StateMachine.tx_fifo: Return the number of TX FIFO items, 0 if empty
restart() seems to be the most useful one, as it resets the state machine
to the initial state without the need to re-initialise/re-create. It also
makes PIO code easier, because then stalling as an error state can be
unlocked.
rx_fifo() is also useful, for MP code to check for data and timeout if no
data arrived. Complex logic is easier handled in Python code than in PIO
code.
tx_fifo() can be useful to check states where data is not processed, and is
mostly for symmetry.
The implementation samples rosc.randombits at a frequency lower than the
oscillator frequency. This gives better random values. In addition, for
an 8-bit value 8 samples are taken and fed through a 8-bit CRC,
distributing the sampling over the byte. The resulting sampling rate is
about 120k/sec.
The RNG does not include testing of error conditions, like the ROSC being
in sync with the sampling or completely failing. Making the interim value
static causes it to perform a little bit better in short sync or drop-out
situations.
The output of uos.urandom() performs well with the NIST800-22 test suite.
In my trial it passed all tests of the sts 2.1.2 test suite. I also ran a
test of the random data with the Common Criteria test suite AIS 31, and it
passed all tests too.
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.
Signed-off-by: Alexander Ziubin aziubin@googlemail.com
This commit simplifies the customisation of the main MicroPython execution
loop (4 macros are reduced to 2), and allows a board to have full control
over the execution (or not) of boot.py and main.py.
For boards that use the default start-up code, there is no functional
change in this commit.
Signed-off-by: Damien George <damien@micropython.org>
This update to the PR retains the earlier board rev (with a rename) so
that backward binary compatibility is not lost for the earlier board
revision. The primary name 'vina-d51' is retained for the latest
revision to make it easy for customers to select the proper UF2
download - because the name matches the commercial name.
Details:
Replace bdmicro_vina_d51 with bdmicro_vina_d51_pcb7 (revision 7 of
PCB) with boardfiles unmodified. Add _pcb7 to the workflow build.
Replace bdmicro_vina_d51 boardfile content with latest PCB updates
(revision 10 ov PCB). Add minimal comments in the board files to make
it clear which PCB revision is implemented. Update the USB PID to
reflect an updated board revision.
Per CPython everything which comes after the command, module or file
argument is not an option for the interpreter itself. Hence the processing
of options should stop when encountering those, and the remainder be passed
as sys.argv. Note the latter was already the case for a module or file but
not for a command.
This fixes issues like 'micropython myfile.py -h' showing the help and
exiting instead of passing '-h' as sys.argv[1], likewise for
'-X <something>' being treated as a special option no matter where it
occurs on the command line.
Some forum users noticed that `sm.exec()` took longer the more was present
on the flash filesystem connected to the RP2040. They traced this back to
the `array` import inside `asm_pio()`, which is causing MicroPython to scan
the filesystem.
uarray is a built-in module, so importing it shouldn't require scanning the
filesystem.
We avoid moving the import to the top-level in order to keep the namespace
clean; we don't want to accidentally expose `rp2.array`.
Support for C++ was added in 97960dc7de but
that commit didn't include the C++ exception handling table in the binary
firmware image. This commit fixes that.
Signed-off-by: Damien George <damien@micropython.org>
This is a workaround for errata RP2040-E5, and is needed to make USB more
reliable on certain USB ports.
Signed-off-by: Damien George <damien@micropython.org>
ESP-01 header renamed to AUX, and expanded to 12 pins from 8
pins. Pins 1-8 still accommodate the ESP-01, with expansion to full
SERCOM 4-pad support to allow for SPI and I2C on that expansion port
with additional GPIO control.
Update pins.c with additional signals provided AUX_1-8, along with
UART, SPI, I2C name usage as aliases to appropriate AUX_1-8
signals. Additionally, add several alternate names specific to several
expansion modules - the ESP-01, and the ATW-01 using the WINC_1500
(SPI) w/interrupt and control needed for the WINC - with assignments
to module pin positions.
Re-work SERCOM assignments to accommodate the above from other parts
of the board, which required moving a SERCOM or two around in order to
accommodate the 4-pad sercom pin mapping on the AUX port.
Built and tested using latest from 'main':
Adafruit CircuitPython 6.2.0-rc.0-70-ga1562430f-dirty on 2021-04-05;
BDMICRO VINA-D51 with samd51n20
After this change, the following program works for me on the MIMXRT1010-EVK:
```python
import pwmio
import board
p = pwmio.PWMOut(board.D13, frequency=1_000_000, variable_frequency=True)
p.duty_cycle = 32868
while True:
pass
```
Querying and varying the duty_cycle and frequency work as well.
The lowest frequency obtainable is about 2kHz; there is an additional
divider which would allow lower PWM frequencies (I think 1kHz is important
for servos?)
Something odd happens with very low duty cycles, such as
```python
>>> p.frequency = 2000
>>> p.duty_cycle = 2
```
instead of a symmetrical waveform, it's asymmetrical. With `duty_cycle=4`,
the effect disappears. The reason for this is probably hidden in the
datasheet, but could affect servos or other things that count pulse
widths.
It's a bit of a pitfall with user C modules that including them in the
build does not automatically enable them. This commit changes the docs and
examples for user C modules to encourage writers of user C modules to
enable them unconditionally. This makes things simpler and covers most use
cases.
See discussion in issue #6960, and also #7086.
Signed-off-by: Damien George <damien@micropython.org>
It was noticed that the esp32 port didn't build ulab correctly. The
problem was a multiple defintion of the 'mp_hal_stdout_tx_str' and
'mp_hal_stdout_tx_strn_cooked' functions.
They were defined in stdout_helpers.c but also in the
ports/esp32/mphalport.c.
Fixed by removing stdout_helpers.c from the build.
Signed-off-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
Support for User C and C++ modules was lost due to upgrading the esp32 to
the latest CMake based IDF from the GNUMakefile build process.
Restore the support for the esp32 port by integrating with the approach
recently added for the rp2 port.
Signed-off-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
This allows more options to be overridden to 0 in an mpconfigboard.mk.
Improved:
* FRAMEBUFFERIO, FULL_BUILD, BITOPS, PWMIO, RGBMATRIX, OTARYIO, PULSEIO, WATCHDOG
Still problematic (pull requests welcome):
* RP2PIO & NEOPIXEL_WRITE, possibly only if a status neopixel is defined
* BITBANGIO, possibly only if BUSIO is enabled
* RTC
Incidentally, with RP2PIO & NEOPIXEL_WRITE, BITBANGIO, and RTC re-enabled I get
```
323956 bytes used, 720524 bytes free in flash firmware space out of 1044480 bytes (1020.0kB).
12072 bytes used, 250072 bytes free in ram for stack and heap out of 262144 bytes (256.0kB).
```
Closes#4515
This USB feature is currently not supported. With this flag enabled (and
the feature not implemented) the USB serial will stop working if there is a
delay of more than about 2 seconds between messages, which can occur with
USB autosuspend enabled.
Fixes issue #6866.
The parts that are generic are added to py/ so they can be used by other
ports that use CMake.
py/usermod.cmake:
* Creates a usermod target to hang user C/CXX modules from.
* Gathers sources from user C/CXX modules and libs for QSTR scan.
ports/rp2/CMakeLists.txt:
* Includes py/usermod.cmake.
* Links the resulting usermod library to the MicroPython target.
py/mkrules.cmake:
Add cxxflags to qstr.i.last custom command for CXX modules:
* MICROPY_CPP_FLAGS so CXX modules will find includes.
* -DNO_QSTR to fix fatal error missing "genhdr/qstrdefs.generated.h".
Usage:
The rp2 port can be linked against user C modules by running:
make USER_C_MODULES=/path/to/module/micropython.cmake
CMake will print a list of included modules.
Co-authored-by: Graham Sanderson <graham.sanderson@raspberrypi.org>
Co-authored-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
Signed-off-by: Phil Howard <phil@pimoroni.com>
Set the betweenTransferDelay to the SCK low-time, to avoid long pauses
between bytes (transfers) while preventing the last SCK cycle in a byte
from being a runt pulse.
Compared to an earlier revision of this change, which just set the delays
all to zero, this doesn't break using an AirLift, which was sensitive
to the runt pulses (the simple loopback-wire test didn't detect the problem)
without this, the baud rate could be wrong; in my testing, it was
low by a factor of 2 when requesating baudrate=1_000_000 (1MHz).
When passing the baudrate in to LPSPI_MasterInit, the setting is made
automatically, but LPSPI_MAster_SetBaudRate just returns it via the
out-parameter tcrPrescaleValue.
There are DNP resistors on the MIMXRT1010-EVK board (see SCH-45852)
that lead to these pins on the arduino-style header not being connected
through. In theory someone could populate them, but as it the presence
of these names in the pins module caused problems when they didn't work
as expected.
Closes#3012
This commit simplifies and cleans up the bare-arm port, and adds just
enough system and library code to make it execute on an STM32F405 MCU.
The mpconfigport.h configuration is simplified to just specify those
configuration values that are different from the defaults. And the
addition of -fdata-sections and -ffunction-sections means the final
firmware is smaller than it previously was, by about 4200 bytes.
A README is also added.
Signed-off-by: Damien George <damien@micropython.org>
This switches stage2 to C and uses Jinja to change the C code based
on flash settings from https://github.com/adafruit/nvm.toml. It
produces the fastest settings for the given set of external flashes.
Flash size is no longer hard coded so switching flashes with similar
capabilities but different sizes should *just work*.
This PR also places "ITCM" code in RAM to save the XIP cache for
code execution. Further optimization is possible. A blink code.py
still requires a number of flash fetches every blink.
Fixes#4041
The I2C.c for RP2040 included a special case for writes <=2 bytes to match the MicroPython implementation,
however RP2040 does support 1 and 2 byte reads, with only 0 bytes being the exception.
Signed-off-by: Philip Howard <phil@pimoroni.com>
The GNU Make dir command uses spaces as item separator so it does not
work for e.g building the STM32 port on Cygwin with a default Arm
installation in "c:/program files (x86)/GNU Arm Embedded Toolchain".
Fix by using POSIX dirname on a quoted path instead.
