rp2: Add support for building different board configurations.
This change allows to build firmware for different rp2-based boards, following how it is done in other ports like stm32 and esp32. So far only the original Pico and Adafruit Feather RP2040 are added. Board names should match (sans case) those in pico-sdk/src/boards/include/boards/. Usage: Pico firmware can be build either using make as previously (it is the default board) or by `make BOARD=PICO`. Feather is built by `make BOARD=ADAFRUIT_FEATHER_RP2040`. Only the board name and flash drive size is set, pin definition is taken from the appropriate pico-sdk board definition. Firmware is saved in the directory build-BOARD_NAME.
This commit is contained in:
parent
1be74b94b6
commit
7ca686684e
@ -17,6 +17,30 @@ endif()
|
||||
# Use the local tinyusb instead of the one in pico-sdk
|
||||
set(PICO_TINYUSB_PATH ${MICROPY_DIR}/lib/tinyusb)
|
||||
|
||||
# Set the location of this port's directory.
|
||||
set(MICROPY_PORT_DIR ${CMAKE_SOURCE_DIR})
|
||||
|
||||
# Set the board if it's not already set.
|
||||
if(NOT MICROPY_BOARD)
|
||||
set(MICROPY_BOARD PICO)
|
||||
endif()
|
||||
|
||||
# Set the PICO_BOARD if it's not already set.
|
||||
if(NOT PICO_BOARD)
|
||||
string(TOLOWER ${MICROPY_BOARD} PICO_BOARD)
|
||||
endif()
|
||||
|
||||
# Set the board directory and check that it exists.
|
||||
if(NOT MICROPY_BOARD_DIR)
|
||||
set(MICROPY_BOARD_DIR ${MICROPY_PORT_DIR}/boards/${MICROPY_BOARD})
|
||||
endif()
|
||||
if(NOT EXISTS ${MICROPY_BOARD_DIR}/mpconfigboard.cmake)
|
||||
message(FATAL_ERROR "Invalid MICROPY_BOARD specified: ${MICROPY_BOARD}")
|
||||
endif()
|
||||
|
||||
# Include board config
|
||||
include(${MICROPY_BOARD_DIR}/mpconfigboard.cmake)
|
||||
|
||||
# Include component cmake fragments
|
||||
include(${MICROPY_DIR}/py/py.cmake)
|
||||
include(${MICROPY_DIR}/extmod/extmod.cmake)
|
||||
@ -150,6 +174,7 @@ target_link_libraries(${MICROPY_TARGET} usermod)
|
||||
target_include_directories(${MICROPY_TARGET} PRIVATE
|
||||
${MICROPY_INC_CORE}
|
||||
${MICROPY_INC_USERMOD}
|
||||
${MICROPY_BOARD_DIR}
|
||||
"${PROJECT_SOURCE_DIR}"
|
||||
"${CMAKE_BINARY_DIR}"
|
||||
)
|
||||
|
@ -2,11 +2,13 @@
|
||||
#
|
||||
# This is a simple wrapper around cmake
|
||||
|
||||
BUILD = build
|
||||
BOARD ?= PICO
|
||||
|
||||
BUILD ?= build-$(BOARD)
|
||||
|
||||
$(VERBOSE)MAKESILENT = -s
|
||||
|
||||
CMAKE_ARGS =
|
||||
CMAKE_ARGS = -DMICROPY_BOARD=$(BOARD)
|
||||
|
||||
ifdef USER_C_MODULES
|
||||
CMAKE_ARGS += -DUSER_C_MODULES=${USER_C_MODULES}
|
||||
|
@ -0,0 +1 @@
|
||||
# cmake file for Adafruit Feather RP2040
|
3
ports/rp2/boards/ADAFRUIT_FEATHER_RP2040/mpconfigboard.h
Normal file
3
ports/rp2/boards/ADAFRUIT_FEATHER_RP2040/mpconfigboard.h
Normal file
@ -0,0 +1,3 @@
|
||||
// Board and hardware specific configuration
|
||||
#define MICROPY_HW_BOARD_NAME "Adafruit Feather RP2040"
|
||||
#define MICROPY_HW_FLASH_STORAGE_BYTES (3072 * 1024)
|
1
ports/rp2/boards/PICO/mpconfigboard.cmake
Normal file
1
ports/rp2/boards/PICO/mpconfigboard.cmake
Normal file
@ -0,0 +1 @@
|
||||
# cmake file for Raspberry Pi Pico
|
3
ports/rp2/boards/PICO/mpconfigboard.h
Normal file
3
ports/rp2/boards/PICO/mpconfigboard.h
Normal file
@ -0,0 +1,3 @@
|
||||
// Board and hardware specific configuration
|
||||
#define MICROPY_HW_BOARD_NAME "Raspberry Pi Pico"
|
||||
#define MICROPY_HW_FLASH_STORAGE_BYTES (1408 * 1024)
|
@ -31,8 +31,9 @@
|
||||
#include "hardware/sync.h"
|
||||
#include "pico/binary_info.h"
|
||||
|
||||
#include "mpconfigboard.h"
|
||||
|
||||
// Board and hardware specific configuration
|
||||
#define MICROPY_HW_BOARD_NAME "Raspberry Pi Pico"
|
||||
#define MICROPY_HW_MCU_NAME "RP2040"
|
||||
#define MICROPY_HW_ENABLE_UART_REPL (0) // useful if there is no USB
|
||||
#define MICROPY_HW_ENABLE_USBDEV (1)
|
||||
|
Loading…
Reference in New Issue
Block a user