stm32lib now provides system_stm32XXxx.c source files for all MCU variants,
which includes SystemInit and prescaler tables. Since these are quite
standard and don't need to be changed, switch to use them instead of custom
variants, making the start-up code cleaner.
The SystemInit code in stm32lib was checked and is equivalent to what is
removed from the stm32 port in this commit.
This is a start to make a more consistent machine.RTC class across ports.
The stm32 pyb.RTC class at least has the datetime() method which behaves
the same as esp8266 and esp32, and with this patch the ntptime.py script
now works with stm32.
If both FS and HS USB peripherals are enabled for a board then the active
one used for the REPL will now be auto-detected, by checking to see if both
the DP and DM lines are actively pulled low. By default the code falls
back to use MICROPY_HW_USB_MAIN_DEV if nothing can be detected.
When going out of memory-mapped mode to do a control transfer to the QSPI
flash, the MPU settings must be changed to forbid access to the memory
mapped region. And any ongoing transfer (eg memory mapped continuous read)
must be aborted.
The Cortex-M7 CPU will do speculative loads from any memory location that
is not explicitly forbidden. This includes the QSPI memory-mapped region
starting at 0x90000000 and with size 256MiB. Speculative loads to this
QSPI region may 1) interfere with the QSPI peripheral registers (eg the
address register) if the QSPI is not in memory-mapped mode; 2) attempt to
access data outside the configured size of the QSPI flash when it is in
memory-mapped mode. Both of these scenarios will lead to issues with the
QSPI peripheral (eg Cortex bus lock up in scenario 2).
To prevent such speculative loads from interfering with the peripheral the
MPU is configured in this commit to restrict access to the QSPI mapped
region: when not memory mapped the entire region is forbidden; when memory
mapped only accesses to the valid flash size are permitted.
Commit 9e68eec8ea introduced a regression
where the PID of the USB device would be 0xffff if the default value was
used. This commit fixes that by using a signed int type.
Entering a bootloader (ST system bootloader, or custom mboot) from software
by directly branching to it is not reliable, and the reliability of it
working can depend on the peripherals that were enabled by the application
code. It's also not possible to branch to a bootloader if the WDT is
enabled (unless the bootloader has specific provisions to feed the WDT).
This patch changes the way a bootloader is entered from software by first
doing a complete system reset, then branching to the desired bootloader
early on in the start-up process. The top two words of RAM (of the stack)
are reserved to store flags indicating that the bootloader should be
entered after a reset.
Previously the end of the heap was the start (lowest address) of the stack.
With the changes in this commit these addresses are now independent,
allowing a board to place the heap and stack in separate locations.
With this the user can select multiple logical units to expose over USB MSC
at once, eg: pyb.usb_mode('VCP+MSC', msc=(pyb.Flash(), pyb.SDCard())). The
default behaviour is the original behaviour of just one unit at a time.
Eventually these responses could be filled in by a function to make their
contents dynamic, depending on the attached logical units. But for now
they are fixed, and this patch fixes the MODE SENSE(6) responses so it is
the correct length with the correct header.
SCSI can support multiple logical units over the one interface (in this
case over USBD MSC) and here the MSC code is reworked to support this
feature. At this point only one LU is used and the behaviour is mostly
unchanged from before, except the INQUIRY result is different (it will
report "Flash" for both flash and SD card).
To use it a board should define MICROPY_PY_USSL=1 and MICROPY_SSL_MBEDTLS=1
at the Makefile level. With the provided configuration it adds about 64k
to the build.
It doesn't work to tie the polling of an underlying NIC driver (eg to check
the NIC for pending Ethernet frames) with its associated lwIP netif. This
is because most NICs are implemented with IRQs and don't need polling,
because there can be multiple lwIP netif's per NIC driver, and because it
restricts the use of the netif->state variable. Instead the NIC should
have its own specific way of processing incoming Ethernet frame.
This patch removes this generic NIC polling feature, and for the only
driver that uses it (Wiznet5k) replaces it with an explicit call to the
poll function (which could eventually be improved by using a proper
external interrupt).
If the board-pin name is left empty then only the cpu-pin name is used, eg
",PA0". If the board-pin name starts with a hyphen then it's available as
a C definition but not in the firmware, eg "-X1,PA0".
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
Set the active MPU region to the actual size of SDRAM configured and
invalidate the rest of the memory-mapped region, to prevent errors due to
CPU speculation. Also update the attributes of the SDRAM region as per ST
recommendations, and change region numbers to avoid conflicts elsewhere in
the codebase (see eth usage).
On MCUs that have an I2C TIMINGR register, this can now be explicitly set
via the "timingr" keyword argument to the I2C constructor, for both
machine.I2C and pyb.I2C. This allows to configure precise timing values
when the defaults are inadequate.
Previously the hardware I2C timeout was hard coded to 50ms which isn't
guaranteed to be enough depending on the clock stretching specs of the I2C
device(s) in use.
This patch ensures the hardware I2C implementation honors the existing
timeout argument passed to the machine.I2C constructor. The default
timeout for software and hardware I2C is now 50ms.
Recent gcc versions (at least 9.1) give a warning about using "sp" in the
clobber list. Such code is removed by this patch. A dedicated function is
instead used to set SP and branch to the bootloader so the code has full
control over what happens.
Fixes issue #4785.
Before this change, if the USB was reconnected it was possible that some
characters in the TX buffer were retransmitted because tx_buf_ptr_out and
tx_buf_ptr_out_shadow were reset while tx_buf_ptr_in wasn't. That
behaviour is fixed here by retaining the TX buffer state across reconnects.
Fixes issue #4761.
The new function factory_reset_make_files() populates the given filesystem
with the default factory files. It is defined with weak linkage so it can
be overridden by a board.
This commit also brings some minor user-facing changes:
- boot.py is now no longer created unconditionally if it doesn't exist, it
is now only created when the filesystem is formatted and the other files
are populated (so, before, if the user deleted boot.py it would be
recreated at next boot; now it won't be).
- pybcdc.inf and README.txt are only created if the board has USB, because
they only really make sense if the filesystem is exposed via USB.
It's more common to need non-blocking behaviour when reading from a UART,
rather than having a large timeout like 1000ms (the original behaviour).
With a large timeout it's 1) likely that the function will read forever if
characters keep trickling it; or 2) the function will unnecessarily wait
when characters come sporadically, eg at a REPL prompt.
The alternate function pin allocations are different to other NUCLEO-144
boards. This is because the STM32F413 has a very high peripheral count:
10x UART, 5x SPI, 3x I2C, 3x CAN. The pinout was chosen to expose all
these devices on separate pins except CAN3 which shares a pin with UART1
and SPI1 which shares pins with DAC.
Includes:
- Support for CAN3.
- Support for UART9 and UART10.
- stm32f413xg.ld and stm32f413xh.ld linker scripts.
- stm32f413_af.csv alternate function mapping.
- startup_stm32f413xx.s because F413 has different interrupt vector table.
- Memory configuration with: 240K filesystem, 240K heap, 16K stack.
This patch makes pllvalues.py generate two tables: one for when HSI is used
and one for when HSE is used. The correct table is then selected at
compile time via the existing MICROPY_HW_CLK_USE_HSI.
On the STM32F722 (at least, but STM32F767 is not affected) the CK48MSEL bit
must be deselected before PLLSAION is turned off, or else the 48MHz
peripherals (RNG, SDMMC, USB) may get stuck without a clock source.
In such "lock up" cases it seems that these peripherals are still being
clocked from the PLLSAI even though the CK48MSEL bit is turned off. A hard
reset does not get them out of this stuck state. Enabling the PLLSAI and
then disabling it does get them out. A test case to see this is:
import machine, pyb
for i in range(100):
machine.freq(122_000000)
machine.freq(120_000000)
print(i, [pyb.rng() for _ in range(4)])
On occasion the RNG will just return 0's, but will get fixed again on the
next loop (when PLLSAI is enabled by the change to a SYSCLK of 122MHz).
Fixes issue #4696.
The stm32 and nrf ports already had the behaviour that they would first
check if the script exists before executing it, and this patch makes all
other ports work the same way. This helps when developing apps because
it's hard to tell (when unconditionally trying to execute the scripts) if
the resulting OSError at boot up comes from missing boot.py or main.py, or
from some other error. And it's not really an error if these scripts don't
exist.
This patch makes the DAC driver simpler and removes the need for the ST
HAL. As part of it, new helper functions are added to the DMA driver,
which also use direct register access instead of the ST HAL.
Main changes to the DAC interface are:
- The DAC uPy object is no longer allocated dynamically on the heap,
rather it's statically allocated and the same object is retrieved for
subsequent uses of pyb.DAC(<id>). This allows to access the DAC objects
without resetting the DAC peripheral. It also means that the DAC is only
reset if explicitly passed initialisation parameters, like "bits" or
"buffering".
- The DAC.noise() and DAC.triangle() methods now output a signal which is
full scale (previously it was a fraction of the full output voltage).
- The DAC.write_timed() method is fixed so that it continues in the
background when another peripheral (eg SPI) uses the DMA (previously the
DAC would stop if another peripheral finished with the DMA and shut the
DMA peripheral off completely).
Based on the above, the following backwards incompatibilities are
introduced:
- pyb.DAC(id) will now only reset the DAC the first time it is called,
whereas previously each call to create a DAC object would reset the DAC.
To get the old behaviour pass the bits parameter like: pyb.DAC(id, bits).
- DAC.noise() and DAC.triangle() are now full scale. To get previous
behaviour (to change the amplitude and offset) write to the DAC_CR (MAMP
bits) and DAC_DHR12Rx registers manually.
If MICROPY_HW_RTC_USE_BYPASS is enabled the RTC startup goes as follows:
- RTC is started with LSE in bypass mode to begin with
- if that fails to start (after a given timeout) then LSE is reconfigured
in non-bypass
- if that fails to start then RTC is switched to LSI
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
These macros are unused, and they can conflict with other entities by the
same name. If needed they can be provided as static inline functions, or
just functions.
Fixes issue #4559.
To use HSI instead of HSE define MICROPY_HW_CLK_USE_HSI as 1 in the board
configuration file. The default is to use HSE.
HSI has been made the default for the NUCLEO_F401RE board to serve as an
example, and because early revisions of this board need a hardware
modification to get HSE working.
This demonstrates how to use external QSPI flash in XIP (execute in place)
mode. The default configuration has all extmod/ code placed into external
QSPI flash, but other code can easily be put there by modifying the custom
f769_qspi.ld script.
A board can now use the make variables TEXT0_SECTIONS and TEXT1_SECTIONS to
specify the linker sections that should go in its firmware. Defaults are
provided which give the existing behaviour.
Currently all usages of mp_hal_pin_config_alt_static() set the pin speed to
"high" (50Mhz). The SDRAM interface typically runs much faster than this
so should be set to the maximum pin speed.
This commit adds mp_hal_pin_config_alt_static_speed() which allows setting
the pin speed along with the other alternate function details.
A few RTC constants weren't being parsed properly due to whitespace
differences, and this patch makes certain whitespace optional. Changes
made:
- allow for no space between /*!< and EXTI, eg for:
__IO uint32_t IMR; /*!<EXTI Interrupt mask register, Address offset: 0x00 */
- allow for no space between semicolon and start of comment, eg for:
__IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */
Replaces "PYB: soft reboot" with "MPY: soft reboot", etc.
Having a consistent prefix across ports reduces the difference between
ports, which is a general goal. And this change won't break pyboard.py
because that tool only looks for "soft reboot".
Instead of checking each callback (currently storage and dma) explicitly
for each SysTick IRQ, use a simple circular function table indexed by the
lower bits of the millisecond tick counter. This allows callbacks to be
easily enabled/disabled at runtime, and scales well to a large number of
callbacks.
This is a good board to demonstrate the use of Mboot because it only has a
USB HS port exposed so the native ST DFU mode cannot be used. With Mboot
this port can be used.
If a custom bootloader is enabled (eg mboot) then machine.bootloader() will
now enter that loader. To get the original ST DFU loader pass any argument
to the function, like machine.bootloader(1).
With clock bypass enabled the attached SD card is clocked at the maximum
48MHz. But some SD cards are unreliable at these rates. Although it's
nice to have high speed transfers it's more important that the transfers
are reliable for all cards. So disable this clock bypass option.
This way the UART REPL does not need the MicroPython heap and exists
outside the MicroPython runtime, allowing characters to still be received
during a soft reset.
The new compile-time option is MICROPY_HW_USB_MAX_POWER_MA. Set this in
the board configuration file to the maximum current in mA that the board
will draw over USB. The default is 500mA.
The new compile-time option is MICROPY_HW_USB_SELF_POWERED. Set this
option to 1 in the board configuration file to indicate that the USB device
is self powered. This option is disabled by default (previous behaviour).
It can be that LSEON and LSERDY are set yet the RTC is not enabled (this
can happen for example when coming out of the ST DFU mode on an F405 with
the RTC not previously initialised). In such a case the RTC is never
started because the code thinks it's already running. This patch fixes
this case by always checking if RTCEN is set when booting up (and also
testing for a valid RTCSEL value in the case of using an LSE).
Without the static qualifier these objects will be kept by the linker even
if they are unused. So this patch saves some RAM when these features are
unused by a board.
On MCUs other than F4 the ORE (overrun error) flag needs to be cleared
independently of clearing RXNE, even though both are wired to trigger the
same RXNE IRQ. In the case that an overrun occurred it's necessary to
explicitly clear the ORE flag or else the RXNE interrupt will keep firing.
Otherwise IRQs may not be enabled for the user UART.irq() handler. In
particular this fixes the user IRQ_RXIDLE interrupt so that it triggers
even when there is no RX buffer.
The new option MICROPY_HW_SDCARD_MOUNT_AT_BOOT can now be defined to 0 in
mpconfigboard.h to allow SD hardware to be enabled but not auto-mounted at
boot. This feature is enabled by default to retain previous behaviour.
Previously, if an SD card is enabled in hardware it is also used to boot
from. While this can be disabled with a SKIPSD file on internal flash,
this wont be available at first boot or if the internal flash gets
corrupted.
This UART_HandleTypeDef is quite large (around 70 bytes in RAM needed for
each UART object) and is not needed: instead the state of the peripheral
held in its registers provides all the required information.
The pin alternate function information is derived from ST's datasheet
https://www.st.com/resource/en/datasheet/stm32l432kc.pdf
In the datasheet, the line 2 of AF4 includes I2C2 but actually the chip
does not have I2C2 so it is removed.
As per the machine.UART documentation, this is used to set the length of
the RX buffer. The legacy read_buf_len argument is retained for backwards
compatibility, with rxbuf overriding it if provided.
Also change the order of printing of flow so it is after stop (so bits,
parity, stop are one after the other), and reduce code size by using
mp_print_str instead of mp_printf where possible.
See issue #1981.
Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to
regularly check if buffered data needed to be sent out to the USB host.
This wasted resources (CPU, power) if no data needed to be sent.
This commit changes how the USB CDC transmits buffered data:
- When new data is first available to send the data is queued immediately
on the USB IN endpoint, ready to be sent as soon as possible.
- Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait.
- When the low-level USB driver has finished sending out the data queued
in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately
queues any outstanding data, waiting for the next IN frame.
The benefits on this new approach are:
- SOF IRQ does not need to run continuously so device has a better chance
to sleep for longer, and be more responsive to other IRQs.
- Because SOF IRQ is off, current consumption is reduced by a small amount,
roughly 200uA when USB is connected (measured on PYBv1.0).
- CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is
unchanged).
- When USB is connected, Python code that is executing is slightly faster
because SOF IRQ no longer interrupts continuously.
- On F733 with USB HS, CDC tx throughput is about the same as prior to this
commit.
- On F733 with USB HS, Python code is about 5% faster because of no SOF.
As part of this refactor, the serial port should no longer echo initial
characters when the serial port is first opened (this only used to happen
rarely on USB FS, but on USB HS is was more evident).
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).
As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot. On boards with SDRAM enabled the heap
has been set to use that.
Configuring clocks is a critical operation and is best to avoid when
possible. If the clocks really need to be reset to the same values then
one can pass in a slightly higher value, eg 168000001 Hz to get 168MHz.
