stm32/boards: Add NUCLEO_L432KC board configuration files.
This commit is contained in:
parent
9d3372bded
commit
69b7b8fa12
59
ports/stm32/boards/NUCLEO_L432KC/mpconfigboard.h
Normal file
59
ports/stm32/boards/NUCLEO_L432KC/mpconfigboard.h
Normal file
@ -0,0 +1,59 @@
|
||||
#define MICROPY_HW_BOARD_NAME "NUCLEO-L432KC"
|
||||
#define MICROPY_HW_MCU_NAME "STM32L432KC"
|
||||
|
||||
#define MICROPY_EMIT_THUMB (0)
|
||||
#define MICROPY_EMIT_INLINE_THUMB (0)
|
||||
#define MICROPY_PY_USOCKET (0)
|
||||
#define MICROPY_PY_NETWORK (0)
|
||||
#define MICROPY_PY_STM (0)
|
||||
#define MICROPY_PY_PYB_LEGACY (0)
|
||||
#define MICROPY_VFS_FAT (0)
|
||||
|
||||
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
||||
#define MICROPY_HW_ENABLE_RTC (1)
|
||||
#define MICROPY_HW_ENABLE_ADC (1)
|
||||
#define MICROPY_HW_ENABLE_DAC (1)
|
||||
#define MICROPY_HW_ENABLE_TIMER (1)
|
||||
#define MICROPY_HW_HAS_SWITCH (0)
|
||||
|
||||
// MSI is used and is 4MHz
|
||||
#define MICROPY_HW_CLK_PLLM (1)
|
||||
#define MICROPY_HW_CLK_PLLN (16)
|
||||
#define MICROPY_HW_CLK_PLLR (2)
|
||||
#define MICROPY_HW_CLK_PLLP (7)
|
||||
#define MICROPY_HW_CLK_PLLQ (2)
|
||||
|
||||
// UART config
|
||||
#define MICROPY_HW_UART1_TX (pin_B6)
|
||||
#define MICROPY_HW_UART1_RX (pin_B7)
|
||||
#define MICROPY_HW_UART2_TX (pin_A2) // VCP TX
|
||||
#define MICROPY_HW_UART2_RX (pin_A15) // VCP RX
|
||||
|
||||
#define MICROPY_HW_UART_REPL PYB_UART_2
|
||||
#define MICROPY_HW_UART_REPL_BAUD 115200
|
||||
|
||||
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
|
||||
|
||||
// I2C busses
|
||||
#define MICROPY_HW_I2C1_SCL (pin_A9)
|
||||
#define MICROPY_HW_I2C1_SDA (pin_A10)
|
||||
#define MICROPY_HW_I2C3_SCL (pin_A7)
|
||||
#define MICROPY_HW_I2C3_SDA (pin_B4)
|
||||
|
||||
// SPI busses
|
||||
#define MICROPY_HW_SPI1_NSS (pin_B0)
|
||||
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
||||
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
||||
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
||||
#define MICROPY_HW_SPI3_NSS (pin_A4)
|
||||
#define MICROPY_HW_SPI3_SCK (pin_B3)
|
||||
#define MICROPY_HW_SPI3_MISO (pin_B4)
|
||||
#define MICROPY_HW_SPI3_MOSI (pin_B5)
|
||||
|
||||
// LEDs
|
||||
#define MICROPY_HW_LED1 (pin_B3) // Green LD3 LED on Nucleo
|
||||
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
||||
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
||||
|
||||
// USB config
|
||||
#define MICROPY_HW_USB_FS (0)
|
4
ports/stm32/boards/NUCLEO_L432KC/mpconfigboard.mk
Normal file
4
ports/stm32/boards/NUCLEO_L432KC/mpconfigboard.mk
Normal file
@ -0,0 +1,4 @@
|
||||
MCU_SERIES = l4
|
||||
CMSIS_MCU = STM32L432xx
|
||||
AF_FILE = boards/stm32l432_af.csv
|
||||
LD_FILES = boards/stm32l432.ld boards/common_basic.ld
|
47
ports/stm32/boards/NUCLEO_L432KC/pins.csv
Normal file
47
ports/stm32/boards/NUCLEO_L432KC/pins.csv
Normal file
@ -0,0 +1,47 @@
|
||||
D0,PA10
|
||||
D1,PA9
|
||||
D2,PA12
|
||||
D3,PB0
|
||||
D4,PB7
|
||||
D5,PB6
|
||||
D6,PB1
|
||||
D7,PC14
|
||||
D8,PC15
|
||||
D9,PA8
|
||||
D10,PA11
|
||||
D11,PB5
|
||||
D12,PB4
|
||||
D13,PB3
|
||||
A0,PA0
|
||||
A1,PA1
|
||||
A2,PA3
|
||||
A3,PA4
|
||||
A4,PA5
|
||||
A5,PA6
|
||||
A6,PA7
|
||||
A7,PA2
|
||||
PA0,PA0
|
||||
PA1,PA1
|
||||
PA2,PA2
|
||||
PA3,PA3
|
||||
PA4,PA4
|
||||
PA5,PA5
|
||||
PA6,PA6
|
||||
PA7,PA7
|
||||
PA8,PA8
|
||||
PA9,PA9
|
||||
PA10,PA10
|
||||
PA11,PA11
|
||||
PA12,PA12
|
||||
PA15,PA15
|
||||
PB0,PB0
|
||||
PB1,PB1
|
||||
PB3,PB3
|
||||
PB4,PB4
|
||||
PB5,PB5
|
||||
PB6,PB6
|
||||
PB7,PB7
|
||||
PC14,PC14
|
||||
PC15,PC15
|
||||
PH3,PH3
|
||||
LED_GREEN,PB3
|
|
384
ports/stm32/boards/NUCLEO_L432KC/stm32l4xx_hal_conf.h
Executable file
384
ports/stm32/boards/NUCLEO_L432KC/stm32l4xx_hal_conf.h
Executable file
@ -0,0 +1,384 @@
|
||||
/**
|
||||
******************************************************************************
|
||||
* @file stm32l4xx_hal_conf.h
|
||||
* @author MCD Application Team
|
||||
* @version V1.2.0
|
||||
* @date 25-November-2015
|
||||
* @brief HAL configuration template file.
|
||||
* This file should be copied to the application folder and renamed
|
||||
* to stm32l4xx_hal_conf.h.
|
||||
******************************************************************************
|
||||
* @attention
|
||||
*
|
||||
* <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without modification,
|
||||
* are permitted provided that the following conditions are met:
|
||||
* 1. Redistributions of source code must retain the above copyright notice,
|
||||
* this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
* this list of conditions and the following disclaimer in the documentation
|
||||
* and/or other materials provided with the distribution.
|
||||
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
||||
* may be used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
******************************************************************************
|
||||
*/
|
||||
|
||||
/* Define to prevent recursive inclusion -------------------------------------*/
|
||||
#ifndef __STM32L4xx_HAL_CONF_H
|
||||
#define __STM32L4xx_HAL_CONF_H
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
/* Exported types ------------------------------------------------------------*/
|
||||
/* Exported constants --------------------------------------------------------*/
|
||||
|
||||
/* ########################## Module Selection ############################## */
|
||||
/**
|
||||
* @brief This is the list of modules to be used in the HAL driver
|
||||
*/
|
||||
#define HAL_MODULE_ENABLED
|
||||
#define HAL_ADC_MODULE_ENABLED
|
||||
#define HAL_CAN_MODULE_ENABLED
|
||||
/* #define HAL_COMP_MODULE_ENABLED */
|
||||
#define HAL_CORTEX_MODULE_ENABLED
|
||||
/* #define HAL_CRC_MODULE_ENABLED */
|
||||
/* #define HAL_CRYP_MODULE_ENABLED */
|
||||
#define HAL_DAC_MODULE_ENABLED
|
||||
/* #define HAL_DFSDM_MODULE_ENABLED */
|
||||
#define HAL_DMA_MODULE_ENABLED
|
||||
/* #define HAL_FIREWALL_MODULE_ENABLED */
|
||||
#define HAL_FLASH_MODULE_ENABLED
|
||||
/* #define HAL_HCD_MODULE_ENABLED */
|
||||
/* #define HAL_NAND_MODULE_ENABLED */
|
||||
/* #define HAL_NOR_MODULE_ENABLED */
|
||||
/* #define HAL_SRAM_MODULE_ENABLED */
|
||||
#define HAL_GPIO_MODULE_ENABLED
|
||||
#define HAL_I2C_MODULE_ENABLED
|
||||
/* #define HAL_IRDA_MODULE_ENABLED */
|
||||
/* #define HAL_IWDG_MODULE_ENABLED */
|
||||
/* #define HAL_LCD_MODULE_ENABLED */
|
||||
/* #define HAL_LPTIM_MODULE_ENABLED */
|
||||
/* #define HAL_OPAMP_MODULE_ENABLED */
|
||||
#define HAL_PCD_MODULE_ENABLED
|
||||
#define HAL_PWR_MODULE_ENABLED
|
||||
/* #define HAL_QSPI_MODULE_ENABLED */
|
||||
#define HAL_RCC_MODULE_ENABLED
|
||||
#define HAL_RNG_MODULE_ENABLED
|
||||
#define HAL_RTC_MODULE_ENABLED
|
||||
/* #define HAL_SAI_MODULE_ENABLED */
|
||||
/* #define HAL_SD_MODULE_ENABLED */
|
||||
/* #define HAL_SMARTCARD_MODULE_ENABLED */
|
||||
/* #define HAL_SMBUS_MODULE_ENABLED */
|
||||
#define HAL_SPI_MODULE_ENABLED
|
||||
/* #define HAL_SWPMI_MODULE_ENABLED */
|
||||
#define HAL_TIM_MODULE_ENABLED
|
||||
/* #define HAL_TSC_MODULE_ENABLED */
|
||||
#define HAL_UART_MODULE_ENABLED
|
||||
/* #define HAL_USART_MODULE_ENABLED */
|
||||
/* #define HAL_WWDG_MODULE_ENABLED */
|
||||
|
||||
|
||||
/* ########################## Oscillator Values adaptation ####################*/
|
||||
/**
|
||||
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSE is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSE_VALUE)
|
||||
#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
|
||||
#endif /* HSE_VALUE */
|
||||
|
||||
#if !defined (HSE_STARTUP_TIMEOUT)
|
||||
#define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
|
||||
#endif /* HSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief Internal Multiple Speed oscillator (MSI) default value.
|
||||
* This value is the default MSI range value after Reset.
|
||||
*/
|
||||
#if !defined (MSI_VALUE)
|
||||
#define MSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* MSI_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal High Speed oscillator (HSI) value.
|
||||
* This value is used by the RCC HAL module to compute the system frequency
|
||||
* (when HSI is used as system clock source, directly or through the PLL).
|
||||
*/
|
||||
#if !defined (HSI_VALUE)
|
||||
#define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
|
||||
#endif /* HSI_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal High Speed oscillator (HSI48) value for USB FS, SDMMC and RNG.
|
||||
* This internal oscillator is mainly dedicated to provide a high precision clock to
|
||||
* the USB peripheral by means of a special Clock Recovery System (CRS) circuitry.
|
||||
* When the CRS is not used, the HSI48 RC oscillator runs on it default frequency
|
||||
* which is subject to manufacturing process variations.
|
||||
*/
|
||||
#if !defined (HSI48_VALUE)
|
||||
#define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB FS/SDMMC/RNG in Hz.
|
||||
The real value my vary depending on manufacturing process variations.*/
|
||||
#endif /* HSI48_VALUE */
|
||||
|
||||
/**
|
||||
* @brief Internal Low Speed oscillator (LSI) value.
|
||||
*/
|
||||
#if !defined (LSI_VALUE)
|
||||
#define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/
|
||||
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
|
||||
The real value may vary depending on the variations
|
||||
in voltage and temperature. */
|
||||
/**
|
||||
* @brief External Low Speed oscillator (LSE) value.
|
||||
* This value is used by the UART, RTC HAL module to compute the system frequency
|
||||
*/
|
||||
#if !defined (LSE_VALUE)
|
||||
#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
|
||||
#endif /* LSE_VALUE */
|
||||
|
||||
#if !defined (LSE_STARTUP_TIMEOUT)
|
||||
#define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
|
||||
#endif /* HSE_STARTUP_TIMEOUT */
|
||||
|
||||
/**
|
||||
* @brief External clock source for SAI1 peripheral
|
||||
* This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
|
||||
* frequency.
|
||||
*/
|
||||
#if !defined (EXTERNAL_SAI1_CLOCK_VALUE)
|
||||
#define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/
|
||||
#endif /* EXTERNAL_SAI1_CLOCK_VALUE */
|
||||
|
||||
/**
|
||||
* @brief External clock source for SAI2 peripheral
|
||||
* This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
|
||||
* frequency.
|
||||
*/
|
||||
#if !defined (EXTERNAL_SAI2_CLOCK_VALUE)
|
||||
#define EXTERNAL_SAI2_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/
|
||||
#endif /* EXTERNAL_SAI2_CLOCK_VALUE */
|
||||
|
||||
/* Tip: To avoid modifying this file each time you need to use different HSE,
|
||||
=== you can define the HSE value in your toolchain compiler preprocessor. */
|
||||
|
||||
/* ########################### System Configuration ######################### */
|
||||
/**
|
||||
* @brief This is the HAL system configuration section
|
||||
*/
|
||||
#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
|
||||
#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
|
||||
#define USE_RTOS 0
|
||||
#define PREFETCH_ENABLE 1
|
||||
#define INSTRUCTION_CACHE_ENABLE 1
|
||||
#define DATA_CACHE_ENABLE 1
|
||||
|
||||
/* ########################## Assert Selection ############################## */
|
||||
/**
|
||||
* @brief Uncomment the line below to expanse the "assert_param" macro in the
|
||||
* HAL drivers code
|
||||
*/
|
||||
/* #define USE_FULL_ASSERT 1 */
|
||||
|
||||
/* Includes ------------------------------------------------------------------*/
|
||||
/**
|
||||
* @brief Include module's header file
|
||||
*/
|
||||
|
||||
#ifdef HAL_RCC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_rcc.h"
|
||||
#endif /* HAL_RCC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_GPIO_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_gpio.h"
|
||||
#endif /* HAL_GPIO_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DMA_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_dma.h"
|
||||
#endif /* HAL_DMA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DFSDM_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_dfsdm.h"
|
||||
#endif /* HAL_DFSDM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CORTEX_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_cortex.h"
|
||||
#endif /* HAL_CORTEX_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_adc.h"
|
||||
#endif /* HAL_ADC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_can.h"
|
||||
#endif /* HAL_CAN_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_COMP_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_comp.h"
|
||||
#endif /* HAL_COMP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_crc.h"
|
||||
#endif /* HAL_CRC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_CRYP_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_cryp.h"
|
||||
#endif /* HAL_CRYP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_DAC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_dac.h"
|
||||
#endif /* HAL_DAC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FIREWALL_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_firewall.h"
|
||||
#endif /* HAL_FIREWALL_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_FLASH_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_flash.h"
|
||||
#endif /* HAL_FLASH_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SRAM_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_sram.h"
|
||||
#endif /* HAL_SRAM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NOR_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_nor.h"
|
||||
#endif /* HAL_NOR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_NAND_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_nand.h"
|
||||
#endif /* HAL_NAND_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_i2c.h"
|
||||
#endif /* HAL_I2C_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IWDG_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_iwdg.h"
|
||||
#endif /* HAL_IWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LCD_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_lcd.h"
|
||||
#endif /* HAL_LCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_LPTIM_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_lptim.h"
|
||||
#endif /* HAL_LPTIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_OPAMP_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_opamp.h"
|
||||
#endif /* HAL_OPAMP_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PWR_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_pwr.h"
|
||||
#endif /* HAL_PWR_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_qspi.h"
|
||||
#endif /* HAL_QSPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RNG_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_rng.h"
|
||||
#endif /* HAL_RNG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_RTC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_rtc.h"
|
||||
#endif /* HAL_RTC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SAI_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_sai.h"
|
||||
#endif /* HAL_SAI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_sd.h"
|
||||
#endif /* HAL_SD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMBUS_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_smbus.h"
|
||||
#endif /* HAL_SMBUS_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_spi.h"
|
||||
#endif /* HAL_SPI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SWPMI_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_swpmi.h"
|
||||
#endif /* HAL_SWPMI_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_tim.h"
|
||||
#endif /* HAL_TIM_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_TSC_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_tsc.h"
|
||||
#endif /* HAL_TSC_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_uart.h"
|
||||
#endif /* HAL_UART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_USART_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_usart.h"
|
||||
#endif /* HAL_USART_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_IRDA_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_irda.h"
|
||||
#endif /* HAL_IRDA_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_SMARTCARD_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_smartcard.h"
|
||||
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_WWDG_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_wwdg.h"
|
||||
#endif /* HAL_WWDG_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_pcd.h"
|
||||
#endif /* HAL_PCD_MODULE_ENABLED */
|
||||
|
||||
#ifdef HAL_HCD_MODULE_ENABLED
|
||||
#include "stm32l4xx_hal_hcd.h"
|
||||
#endif /* HAL_HCD_MODULE_ENABLED */
|
||||
|
||||
/* Exported macro ------------------------------------------------------------*/
|
||||
#ifdef USE_FULL_ASSERT
|
||||
/**
|
||||
* @brief The assert_param macro is used for function's parameters check.
|
||||
* @param expr: If expr is false, it calls assert_failed function
|
||||
* which reports the name of the source file and the source
|
||||
* line number of the call that failed.
|
||||
* If expr is true, it returns no value.
|
||||
* @retval None
|
||||
*/
|
||||
#define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
|
||||
/* Exported functions ------------------------------------------------------- */
|
||||
void assert_failed(uint8_t* file, uint32_t line);
|
||||
#else
|
||||
#define assert_param(expr) ((void)0)
|
||||
#endif /* USE_FULL_ASSERT */
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
#endif /* __STM32L4xx_HAL_CONF_H */
|
||||
|
||||
|
||||
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
Loading…
Reference in New Issue
Block a user