This patch adds support to mboot for programming external SPI flash. It
allows SPI flash to be programmed via a USB DFU utility in the same way
that internal MCU flash is programmed.
Prior to this patch the QSPI driver assumed that the length of all data
reads and writes was a multiple of 4. This patch allows any length. Reads
are optimised for speed by using 32-bit transfers when possible, but writes
always use a byte transfer because they only use a single data IO line and
are relatively slow.
These examples rely on machine and pyb modules, so they have to get.
Leaving 3 BLE examples that also rely on those modules, but can be
fixed to use CP's modules.
This commit cleans up the pin generation code, all the pins and their
AF (only ADC, for now) are specified in nrf52_af.csv and board use their
own csv file to specify which pins are available on that board and if
they have any special names.
With the only difference between a SD and non-SD build is the linker
file, there's no need to have two separate .mk per board files,
just use a conditional.
The DMA peripheral is limited to transferring 65535 elements at a time so
in order to send more than that the SPI driver must split the transfers up.
The user must be aware of this limit if they are relying on precise timing
of the entire SPI transfer, because there might be a small delay between
the split transfers.
Fixes issue #3851, and thanks to @kwagyeman for the original fix.
This behaviour of a NULL write C method on a stream that uses the write
adaptor objects is no longer supported. It was only ever used by the
coverage build for testing the fail path of mp_get_stream_raise().
If the user button is held down indefinitely (eg unintenionally, or because
the GPIO signal of the user button is connected to some external device)
then it makes sense to end the reset mode cycle with the default mode of
1, which executes code as normal.
It's possible (at least on F4 MCU's) to have RXNE and STOPF set at the same
time during a call to the slave IRQ handler. In such cases RXNE should be
handled before STOPF so that all bytes are processed before
i2c_slave_process_rx_end() is called.
Due to buffering of outgoing bytes on the I2C bus, detection of a NACK
using the ISR_NACKF flag needs to account for the case where ISR_NACKF
corresponds to the previous-to-previous byte.
This patch renames the existing SPI flash API functions to reflect the fact
that the go through the cache:
mp_spiflash_flush -> mp_spiflash_cache_flush
mp_spiflash_read -> mp_spiflash_cached_read
mp_spiflash_write -> mp_spiflash_cached_write
We now track the last time the background task ran and bail on the
PulseIn if it starves the background work. In practice, this
happens after the numbers from pulsein are no longer accurate.
This also adjusts interrupt priorities so most are the lowest level
except for the tick and USB interrupts.
Fixes#516 and #876
The DFU USB config descriptor returns 0x0800=2048 for the supported
transfer size, and this applies to both TX (IN) and RX (OUT). So increase
the rx_buf to support this size without having a buffer overflow on
received data.
With this patch mboot in USB DFU mode now works with dfu-util.
Currently <WLAN>.isconnected() always returns True if a static IP is set,
regardless of the state of the connection.
This patch introduces a new flag 'wifi_sta_connected' which is set in
event_handler() when GOT_IP event is received and reset when DISCONNECTED
event is received (unless re-connect is successful). isconnected() now
simply returns the status of this flag (for STA_IF).
The pre-existing flag misleadingly named 'wifi_sta_connected" is also
renamed to 'wifi_sta_connect_requested'.
Fixes issue #3837
MICROPY_PY_DELATTR_SETATTR can now be enabled without a performance hit for
classes that don't use this feature.
MICROPY_PY_BUILTINS_NOTIMPLEMENTED is a minor addition that improves
compatibility with CPython.
They are now efficient (in runtime performance) and provide a useful
feature that's hard to obtain without them enabled.
See issue #3644 and PR #3826 for background.
Now that the coverage build has fully switched to the VFS sub-system these
functions were no longer available, so add them to the uos_vfs module.
Also, vfs_open is no longer needed, it's available as the built-in open.
The unix coverage build is now switched fully to the VFS implementation, ie
the uos module is the uos_vfs module. For example, one can now sandbox uPy
to their home directory via:
$ ./micropython_coverage
>>> import uos
>>> uos.umount('/') # unmount existing root VFS
>>> vfs = uos.VfsPosix('/home/user') # create new POSIX VFS
>>> uos.mount(vfs, '/') # mount new POSIX VFS at root
Some filesystem/OS features may no longer work with the coverage build due
to this change, and these need to be gradually fixed.
The standard unix port remains unchanged, it still uses the traditional uos
module which directly accesses the underlying host filesystem.
This patch adds support for building the firmware with external SPI RAM
enabled. It is disabled by default because it adds overhead (due to
silicon workarounds) and reduces performance (because it's slower to have
bytecode and objects stored in external RAM).
To enable it, either use "make CONFIG_SPIRAM_SUPPORT=1", or add this line
to you custom makefile/GNUmakefile (before "include Makefile"):
CONFIG_SPIRAM_SUPPORT = 1
When this option is enabled the MicroPython heap is automatically allocated
in external SPI RAM.
Thanks to Angus Gratton for help with the compiler and linker settings.
Also, re-enable calibration storage for CircuitPlayground Express.
Tested with a 500hz PWMOut on Metro M0 with Saleae:
* with crystal 500hz
* with usb 500hz +- 0.1hz
* without either 487hz += 0.1hz
SAMD51 is skipped due to DFLL errata and the fact it defaults to a
factory calibrated 48mhz that works fine for USB.
Fixes#648
This uses the crystal to clock the RTC on boards which have a crystal.
Disable clock generator 2 which was enabled in commit
8e2080411f ("atmel-samd: Add rtc module support").
samd51 differs from samd21 when it comes to the RTC clock. samd51 doesn't
have an explicit clock peripheral so no need for a clock generator.
The same commit didn't even setup XOSC32K correctly, it missed EN1K and XTALEN.
The RTC uses the 1k clock output, so enable it on the OSCULP32K even if it works without it.
Refactor the convoluted asf4 clock setup into something more readable.
enable_clock_generator() has 2 changes:
- Set 'Output enabled' to match the current clock setup
- Handle divisors above 511
Add an enable_clock_generator_sync() version which makes it possible to setup
clocks without waiting for syncing. The bootup would hang without this.
I have checked these registers:
NVMCTRL->CTRLA = 0x00000004
Peripheral clocks (only non-zero shown):
PCHCTRL[1]=0x00000045
PCHCTRL[10]=0x00000041
Generator clocks (only non-zero shown):
GENCTRL[0] = 0x00010907
GENCTRL[1] = 0x00010906
-GENCTRL[2] = 0x00041104
+GENCTRL[2] = 0x00200904
GENCTRL[4] = 0x00010907
GENCTRL[5] = 0x00180906
DFLL clock:
OSCCTRL->DFLLCTRLA = 0x00000082
OSCCTRL->DFLLCTRLB = 0x00000000
OSCCTRL->DFLLVAL = 0x00008082
OSCCTRL->DFLLMUL = 0x00000000
DPLL clocks:
OSCCTRL->Dpll[0].DPLLCTRLA=0x00000002
OSCCTRL->Dpll[0].DPLLCTRLB=0x00000000
OSCCTRL->Dpll[0].DPLLRATIO=0x0000003b
OSCCTRL->Dpll[1].DPLLCTRLA=0x00000080
OSCCTRL->Dpll[1].DPLLCTRLB=0x00000020
OSCCTRL->Dpll[1].DPLLRATIO=0x00000000
OSC32KCTRL clock:
OSC32KCTRL->RTCCTRL = 0x00000000
OSC32KCTRL->XOSC32K = 0x00002082
OSC32KCTRL->CFDCTRL = 0x00000000
OSC32KCTRL->EVCTRL = 0x00000000
OSC32KCTRL->OSCULP32K = 0x00002300
Only gen2 changed which is due to samd51 having more bits in the simple
division register so DIVSEL wasn't necessary, and it didn't have OE set.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
It should be up to the NIC itself to decide if the network interface is
removed upon soft reset. Some NICs can keep the interface up over a soft
reset, which improves usability of the network.
Pins with multiple alt-funcs for the same peripheral (eg USART_CTS_NSS)
need to be split into individual alt-funcs for make-pins.py to work
correctly.
This patch changes the following:
- Split `..._CTS_NSS` into `..._CTS/..._NSS`
- Split `..._RTS_DE` into `..._RTS/..._DE`
- Split `JTDO_SWO` into `JTDO/TRACESWO` for consistency
- Fixed `TRACECK` to `TRACECLK` for consistency
If no block devices are defined by a board then storage support will be
disabled. This means there is no filesystem provided by either the
internal flash or external SPI flash. But the VFS system can still be
enabled and filesystems provided on external devices like an SD card.
Mboot is a custom bootloader for STM32 MCUs. It can provide a USB DFU
interface on either the FS or HS peripherals, as well as a custom I2C
bootloader interface.
These files provide no additional information, all the version and license
information is captured in the relevant files in these subdirectories.
Thanks to @JoeSc for the original patch.
This patch allows to use lwIP as the implementation of the usocket module,
instead of the existing socket-multiplexer that delegates the entire TCP/IP
layer to the NIC itself.
This is disabled by default, and enabled by defining MICROPY_PY_LWIP to 1.
When enabled, the lwIP TCP/IP stack will be included in the build with
default settings for memory usage and performance (see
lwip_inc/lwipopts.h). It is then up to a particular NIC to register itself
with lwIP using the standard lwIP netif API.
Some boards (like the uGame10) may want to have their own set of extra
modules. This change lets them override EXTRA_BUILTIN_MODULES in their
mpconfigboard.h and makes the ugame10 board do that.
This patch makes it so that UART(0) can by dynamically attached to and
detached from the REPL by using the uos.dupterm function. Since WebREPL
uses dupterm slot 0 the UART uses dupterm slot 1 (a slot which is newly
introduced by this patch). UART(0) must now be attached manually in
boot.py (or otherwise) and inisetup.py is changed to provide code to do
this. For example, to attach use:
import uos, machine
uart = machine.UART(0, 115200)
uos.dupterm(uart, 1)
and to detach use:
uos.dupterm(None, 1)
When attached, all incoming chars on UART(0) go straight to stdin so
uart.read() will always return None. Use sys.stdin.read() if it's needed
to read characters from the UART(0) while it's also used for the REPL (or
detach, read, then reattach). When detached the UART(0) can be used for
other purposes.
If there are no objects in any of the dupterm slots when the REPL is
started (on hard or soft reset) then UART(0) is automatically attached.
Without this, the only way to recover a board without a REPL would be to
completely erase and reflash (which would install the default boot.py which
attaches the REPL).
Add CONFIG_NET_DHCPV4, which, after
https://github.com/zephyrproject-rtos/zephyr/pull/5750 works as follows:
static addresses are configured after boot, and DHCP requests are sent
at the same time. If valid DHCP reply is received, it overrides static
addresses.
This setup works out of the box for both direct connection to a
workstation (DHCP server usually is not available) and for connection
to a router (DHCP is available and required).
define CIRCUITPY_BOOT_OUTPUT_FILE will cause mp_hal_stdout_tx_strn() to
invoke before serial_init() is called. Solution is skipped output to
serial if it is not inited.
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC. It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it. The second one is
available for general use.
This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM. Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints. The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
The documentation (including the examples) for elapsed_millis and
elapsed_micros can be found in docs/library/pyb.rst so doesn't need to be
written in full in the source code.
When disabled, the pyb.I2C class saves around 8k of code space and 172
bytes of RAM. The same functionality is now available in machine.I2C
(for F4 and F7 MCUs).
It is still enabled by default.
This driver uses low-level register access to control the I2C peripheral
(ie it doesn't rely on the ST HAL) and provides the same C-level API as the
existing F7 hardware driver.
- Updated supported git hash to current IDF version.
- Added missing targets and includes to Makefile.
- Updated error codes for networking module.
- Added required constant to sdkconfig configuration.
These modules would be very handy to have in order to implement a
more robust replacement for ampy. It costs around 2KiB of text and
no data or bss.
'binascii' has base64 encoding, which can be used to create a fully
8-bit-clean transport above the slightly cooked serial connection of
these boards.
'hashlib' is a bit less critical, but I have found it handy to
be able to robustly checksum remote files.
I see this as only being useful on ports which don't have USB block
device support, so atmel-samd doesn't need it. These modules are
already on esp8266 so I think nrf52 seems like the only one that
needs it.
arturo182
Damien George
jerryneedell
hathach
Scott Shawcroft
Scott Shawcroft
rolandvs
Dan Halbert
Limor "Ladyada" Fried
sommersoft
Nick Moore
Glenn Moloney
Kattni Rembor
Angus Gratton
Matt Wozniski
Noralf Trønnes
Radomir Dopieralski
Daniel Shaulov
Paul Sokolovsky
Tobias Badertscher
Matt Land
Ryan Shaw
Kevin Townsend
Roy Hooper
Peter D. Gray
Bas Wijnen
Jeff Epler