The zephyr function net_shell_cmd_iface() was removed in zephyr v1.14.0,
therefore the MicroPython zephyr port did not build with newer zephyr
versions when CONFIG_NET_SHELL=y. Replace with a more general
shell_exec() function that can execute any zephyr shell command. For
example:
>>> zephyr.shell_exec("net")
Subcommands:
allocs :Print network memory allocations.
arp :Print information about IPv4 ARP cache.
conn :Print information about network connections.
dns :Show how DNS is configured.
events :Monitor network management events.
gptp :Print information about gPTP support.
iface :Print information about network interfaces.
ipv6 :Print information about IPv6 specific information and
configuration.
mem :Print information about network memory usage.
nbr :Print neighbor information.
ping :Ping a network host.
pkt :net_pkt information.
ppp :PPP information.
resume :Resume a network interface
route :Show network route.
stacks :Show network stacks information.
stats :Show network statistics.
suspend :Suspend a network interface
tcp :Connect/send/close TCP connection.
vlan :Show VLAN information.
websocket :Print information about WebSocket connections.
>>> zephyr.shell_exec("kernel")
kernel - Kernel commands
Subcommands:
cycles :Kernel cycles.
reboot :Reboot.
stacks :List threads stack usage.
threads :List kernel threads.
uptime :Kernel uptime.
version :Kernel version.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The -Og optimisation level produces a more realistic build, gives a better
debugging experience, and generates smaller code than -O0, allowing debug
builds to fit in flash.
This commit also assigns variables in can.c to prevent warnings when -Og is
used, and builds a board in CI with DEBUG=1 enabled.
Signed-off-by: Damien George <damien@micropython.org>
Allows reserving CAN, I2C, SPI, Timer and UART peripherals. If reserved
the peripheral cannot be accessed from Python.
Signed-off-by: Damien George <damien@micropython.org>
Even though IRQs are disabled this seems to be required on H7 Rev Y,
otherwise Systick interrupt triggers and the MCU leaves the stop mode
immediately.
This commit saves OSCs/PLLs state before STOP mode and restores them on
exit. Some boards use HSI48 for USB for example, others have PLL2/3
enabled, etc.
Also known as L2CAP "connection oriented channels". This provides a
socket-like data transfer mechanism for BLE.
Currently only implemented for NimBLE on STM32 / Unix.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
This fixes the build for non-STM32WB based boards when the NimBLE submodule
has not been fetched, and also allows STM32WB boards to build with BLE
disabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the STM32WB HCI interface (between the two CPUs) to
require the use of MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS, and as a
consequence to require NimBLE. IPCC RX IRQs now schedule the NimBLE
handler to run via mp_sched_schedule.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead. This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.
The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms. When RX IRQ idle events arrive, it will also schedule this
task to improve latency.
There is a similar change for the unix port where the background thread now
queues the scheduled task.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This requires that the event handlers are called from non-interrupt context
(i.e. the MicroPython scheduler).
This will allow the BLE stack (e.g. NimBLE) to run from the scheduler
rather than an IRQ like PENDSV, and therefore be able to invoke Python
callbacks directly/synchronously. This allows writing Python BLE handlers
for events that require immediate response such as _IRQ_READ_REQUEST (which
was previous a hard IRQ) and future events relating to pairing/bonding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change machine.mem32['foo'] (or using any other non-integer
subscript) could result in a fault due to 'foo' being interpreted as an
integer. And when writing code it's hard to tell if the fault is due to a
bad subscript type, or an integer subscript that specifies an invalid
memory address.
The type of the object used in the subscript is now tested to be an
integer by using mp_obj_get_int_truncated instead of
mp_obj_int_get_truncated. The performance hit of this change is minimal,
and machine.memX objects are more for convenience than performance (there
are many other ways to read/write memory in a faster way),
Fixes issue #6588.
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.
Signed-off-by: Damien George <damien@micropython.org>
Add working example code to provide a starting point for users with files
that they can just copy, and include the modules in the coverage test to
verify the complete user C module build functionality. The cexample module
uses the code originally found in cmodules.rst, which has been updated to
reflect this and partially rewritten with more complete information.
Support building .cpp files and linking them into the micropython
executable in a way similar to how it is done for .c files. The main
incentive here is to enable user C modules to use C++ files (which are put
in SRC_MOD_CXX by py.mk) since the core itself does not utilize C++.
However, to verify build functionality a unix overage test is added. The
esp32 port already has CXXFLAGS so just add the user modules' flags to it.
For the unix port use a copy of the CFLAGS but strip the ones which are not
usable for C++.
The same seed will only occur if the board is the same, the RTC has the
same time (eg freshly powered up) and the first call to this function (eg
via an "import random") is done at exactly the same time since reset.
Signed-off-by: Damien George <damien@micropython.org>
For seeding, the RNG function of the ESP-IDF is used, which is told to be a
true RNG, at least when WiFi or Bluetooth is enabled. Seeding on import is
as per CPython. To obtain a reproducible sequence of pseudo-random numbers
one must explicitly seed with a known value.
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.
This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised. It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.
Signed-off-by: Damien George <damien@micropython.org>
If the device is not connected over USB CDC to a host then all output to
the CDC (eg initial boot messages) is written to the CDC TX buffer with
wrapping, so that the most recent data is retained when the USB CDC is
eventually connected (eg so the REPL banner is displayed upon connection).
This commit fixes a bug in this behaviour, which was likely introduced in
e4fcd216e0, where the initial data in the CDC
TX buffer is repeated multiple times on first connection of the device to
the host.
Signed-off-by: Damien George <damien@micropython.org>
This is a generally useful feature and because it's part of the object
model it cannot be added at runtime by some loadable Python code, so enable
it on the standard unix build.
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).
Signed-off-by: Damien George <damien@micropython.org>
When installing WS firmware, the very first GET_STATE can take several
seconds to respond (especially with the larger binaries like
BLE_stack_full).
Allows stm.rfcore_sys_hci to take an optional timeout, defaulting to
SYS_ACK_TIMEOUT_MS (which is 250ms).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The flash can sometimes be in an already-unlocked state, and attempting to
unlock it again will cause an immediate reset. So make _Flash.unlock()
check FLASH_CR_LOCK to get the current state.
Also fix some magic numbers for FLASH_CR_LOCK AND FLASH_CR_STRT.
The machine.reset() could be removed because it no longer crashes now that
the flash unlock is fixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a script that can be run on-device to install FUS and WS
binaries from the filesystem. Instructions for use are provided in
the rfcore_firmware.py file.
The commit also removes unneeded functionality from the existing rfcore.py
debug script (and renames it rfcore_debug.py).
The new functions provide FUS/WS status, version and SYS HCI commands:
- stm.rfcore_status()
- stm.rfcore_fw_version(fw_id)
- stm.rfcore_sys_hci(ogf, ocf, cmd)
Changes are:
- Fix missing IRQ handler when SDMMC2 is used instead of SDMMC1 with H7
MCUs.
- Removed outdated H7 series compatibility macros.
- Defined common IRQ handler macro for F4 series.
It requires mp_hal_time_ns() to be provided by a port. This function
allows very accurate absolute timestamps.
Enabled on unix, windows, stm32, esp8266 and esp32.
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftSPI constructor is now used soley to create SoftSPI instances, it
can no longer delegate to create a hardware-based SPI instance.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
Zephyr v2.4.0 added a const qualifier to usages of struct device to
allow storing device driver instances exclusively in flash and thereby
reduce ram footprint.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make the instructions more complete by documenting all needed steps for
starting from scratch. Also add a section for MSYS2 since the Travis build
uses it as well and it's a good alternative for Cygwin. Remove the mingw32
reference since it's not readily available anymore in most Linux distros
nor compiles successfully.
The device info table has a different layout when core 2 is in FUS mode.
In particular it's larger than the 32 bytes used when in WS mode and if the
correct amount of space is not allocated then the end of the table may be
overwritten with other data (eg with FUS version 0.5.3). So update the
structure to fix this.
Also update rfcore.py to disable IRQs (which are enabled by rfcore.c), to
not depend on uctypes, and to not require the asm_thumb emitter.
Signed-off-by: Damien George <damien@micropython.org>
And enable this feature on unix, the coverage variant. The .exp test file
is needed so the test can run on CPython versions prior to "@=" operator
support.
Signed-off-by: Damien George <damien@micropython.org>
For time-based functions that work with absolute time there is the need for
an Epoch, to set the zero-point at which the absolute time starts counting.
Such functions include time.time() and filesystem stat return values. And
different ports may use a different Epoch.
To make it clearer what functions use the Epoch (whatever it may be), and
make the ports more consistent with their use of the Epoch, this commit
renames all Epoch related functions to include the word "epoch" in their
name (and remove references to "2000").
Along with this rename, the following things have changed:
- mp_hal_time_ns() is now specified to return the number of nanoseconds
since the Epoch, rather than since 1970 (but since this is an internal
function it doesn't change anything for the user).
- littlefs timestamps on the esp8266 have been fixed (they were previously
off by 30 years in nanoseconds).
Otherwise, there is no functional change made by this commit.
Signed-off-by: Damien George <damien@micropython.org>
To portably get the Epoch. This is simply aliased to localtime() on ports
that are not timezone aware.
Signed-off-by: Damien George <damien@micropython.org>
This commit removes release-specific builds for the esp8266 and makes the
normal build of the GENERIC board more like the release build. This makes
esp8266 like all the other ports, for which there is no difference between
a daily build and a release build, making things less confusing.
Release builds were previously defined by UART_OS=-1 (disable OS messages)
and using manifest_release.py to include more frozen modules.
The changes in this commit are:
- Remove manifest_release.py.
- Add existing modules from manifest_release.py (except example code)
to the GENERIC board's manifest.py file.
- Change UART_OS default to -1 to disable OS messages by default.
Signed-off-by: Damien George <damien@micropython.org>
PPP support was disabled in 96008ff59a -
marked as "unsupported" due to an early IDF v4 release. With the currently
supported IDF v4.x version - 4c81978a - it appears to be working just fine.
This commit changes the default logging level on all esp32 boards to ERROR.
The esp32 port is now stable enough that it makes sense to remove the info
logs to make the output cleaner, and to match other ports. More verbose
logging can always be reenabled via esp.osdebug().
This also fixes issue #6354, error messages from NimBLE: the problem is
that ble.active(True) will cause the IDF's NimBLE port to reset the
"NimBLE" tag back to the default level (which was INFO prior to this
commit). Even if the user had previously called esp.osdebug(None), because
the IDF is setting the "NimBLE" tag back to the default (INFO), the
messages will continue to be shown.
The one quirk is that if the user does want to see the additional logging,
then they must call esp.osdebug(0, 3) after ble.active(True) to undo the
IDF setting the level back to the default (now ERROR). This means that
it's impossible (via Python/esp.osdebug) to see stack-startup logging,
you'd have to recompile with the default level changed back to INFO.
Support freezing modules via manifest.py for consistency with the other
ports. In essence this comes down to calling makemanifest.py and adding
the resulting .c file to the build. Note the file with preprocessed qstrs
has been renamed to match what makemanifest.py expects and which is also
the name all other ports use.
The mpconfigport.h file is an internal header and should only ever be
included once by mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
This allows prototyping rfcore.c improvements from Python.
This was mostly written by @dpgeorge with small modifications to work after
rfcore_init() by @jimmo.
Before this change there was up to a 128ms delay on incoming payloads from
CPU2 as it was polled by SysTick. Now the RX IRQ immediately schedules the
PendSV.
This is required to allow using WS firmware newer than 1.1.1 concurrently
with USB (e.g. USB VCP). It prevents CPU2 from modifying the CLK48 config
on boot.
Tested on WS=1.8 FUS=1.1.
See AN5289 and https://github.com/micropython/micropython/issues/6316
- Split tables and buffers into SRAM2A/2B.
- Use structs rather than word offsets to access tables.
- Use FLASH_IPCCDBA register value rather than option bytes directly.
This allows `ble.active(1)` to fail correctly if the HCI controller is
unavailable.
It also avoids an infine loop in the NimBLE event handler where NimBLE
doesn't correctly detect that the HCI controller is unavailable and keeps
trying to reset.
Furthermore, it fixes an issue where GATT service registrations were left
allocated, which led to a bad realloc if the stack was activated multiple
times.
MicroPython and NimBLE must be on the same core, for synchronisation of the
BLE ringbuf and the MicroPython scheduler. However, in the current IDF
versions (3.3 and 4.0) there are issues (see e.g. #5489) with running
NimBLE on core 1.
This change - pinning both tasks to core 0 - makes it possible to reliably
run the BLE multitests on esp32 boards.
This commit adds support for using Bluetooth on the unix port via a H4
serial interface (distinct from a USB dongle), with both BTstack and NimBLE
Bluetooth stacks.
Note that MICROPY_PY_BLUETOOTH is now disabled for the coverage variant.
Prior to this commit Bluetooth was anyway not being built on Travis because
libusb was not detected. But now that bluetooth works in H4 mode it will
be built, and will lead to a large decrease in coverage because Bluetooth
tests cannot be run on Travis.
Previously the interaction between the different layers of the Bluetooth
stack was different on each port and each stack. This commit defines
common interfaces between them and implements them for cyw43, btstack,
nimble, stm32, unix.
mp_irq_init() is useful when the IRQ object is allocated by the caller.
The mp_irq_methods_t.init method is not used anywhere so has been removed.
Signed-off-by: Damien George <damien@micropython.org>
By setting MICROPY_EPOCH_IS_1970 a port can opt to use 1970/1/1 as the
Epoch for timestamps returned by stat(). And this setting is enabled on
the unix and windows ports because that's what they use.
Signed-off-by: Damien George <damien@micropython.org>
On 32-bit builds these stat fields will overflow a small-int, so use
mp_obj_new_int_from_uint to construct the int object.
Signed-off-by: Damien George <damien@micropython.org>
gettimeofday returns seconds since 2000/1/1 so needs to be adjusted to
seconds since 1970/1/1 to give the correct return value of mp_hal_time_ns.
Signed-off-by: Damien George <damien@micropython.org>
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, if you configure a pin as an output type (I2C in this
example) and then later configure it back as an input, then it will report
the type incorrectly. Example:
>>> import machine
>>> b6 = machine.Pin('B6')
>>> b6
Pin(Pin.cpu.B6, mode=Pin.IN)
>>> machine.I2C(1)
I2C(1, scl=B6, sda=B7, freq=420000)
>>> b6
Pin(Pin.cpu.B6, mode=Pin.ALT_OPEN_DRAIN, pull=Pin.PULL_UP, af=Pin.AF4_I2C1)
>>> b6.init(machine.Pin.IN)
>>> b6
Pin(Pin.cpu.B6, mode=Pin.ALT_OPEN_DRAIN, af=Pin.AF4_I2C1)
With this commit the last print now works:
>>> b6
Pin(Pin.cpu.B6, mode=Pin.IN)
Include storage/flash_map.h unconditionally so we always have access to the
FLASH_AREA_LABEL_EXISTS macro, even if CONFIG_FLASH_MAP is not defined.
This fixes a build error for the qemu_x86 board:
main.c:108:63: error: missing binary operator before token "("
108 | #elif defined(CONFIG_FLASH_MAP) && FLASH_AREA_LABEL_EXISTS(storage)
| ^
../../py/mkrules.mk:88: recipe for target 'build/genhdr/qstr.i.last' failed
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The SCSI driver calls GetCapacity to get the block size and number of
blocks of the underlying block-device/LUN. It caches these values and uses
them later on to verify that reads/writes are within the bounds of the LUN.
But, prior to this commit, there was only one set of cached values for all
LUNs, so the bounds checking for a LUN could use incorrect values, values
from one of the other LUNs that most recently updated the cached values.
This would lead to failed SCSI requests.
This commit fixes this issue by having separate cached values for each LUN.
Signed-off-by: Damien George <damien@micropython.org>
Enabling the following features for all targets, except for nrf51
targets compiled to be used with SoftDevice:
- MICROPY_PY_ARRAY_SLICE_ASSIGN
- MICROPY_PY_SYS_STDFILES
- MICROPY_PY_UBINASCII
Splitting mpconfigport.h into multiple device specific
files in order to facilitate variations between devices.
Due to the fact that the devices might have variations in
features and also variations in flash size it makes sense
that some devices offers more functionality than others
without being limited by restricted devices.
For example more micropython features can be activated for
nrf52840 with 1MB flash, compared to nrf51 with 256KB.
This code is imported from musl, to match existing code in libm_dbl.
The file is also added to the build in stm32/Makefile. It's not needed by
the core code but, similar to c5cc64175b,
allows round() to be used by user C modules or board extensions.
A previous commit 3a9d948032 can cause
lock-ups of the RMT driver, so this commit reverses that, adds a loop_en
flag, and explicitly controls the TX interrupt in write_pulses(). This
provides correct looping, non-blocking writes and sensible behaviour for
wait_done().
See also #6167.
So that micropython-dev can be used to test VFS code, and inspect and build
filesystem images that are compatible with bare-metal systems.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds time.ticks_ms/us support using RTC1 as the timebase. It
also adds the time.ticks_add/diff helper functions. This feature can be
enabled using MICROPY_PY_TIME_TICKS. If disabled the system uses the
legacy sleep methods and does not have any ticks functions.
In addition support for MICROPY_EVENT_POLL_HOOK was added to the
time.sleep_ms(x) function, making this function more power efficient and
allows support for select.poll/asyncio. To support this, the RTC's CCR0
was used to schedule a ~1msec event to wakeup the CPU.
Some important notes about the RTC timebase:
- Since the granularity of RTC1's ticks are approx 30usec, time.ticks_us is
not perfect, does not have 1us resolution, but is otherwise quite usable.
For tighter measurments the ticker's 1MHz counter should be used.
- time.ticks_ms(x) should *not* be called in an IRQ with higher prio than
the RTC overflow irq (3). If so it introduces a race condition and
possibly leads to wrong tick calculations.
See #6171 and #6202.
When compiling for debug (-O0) the .text segment cannot fit the flash
region when MICROPY_ROM_TEXT_COMPRESSION=1, because the compiler does not
optimise away the large if-else chain used to select the correct compressed
string.
This commit enforces MICROPY_ROM_TEXT_COMPRESSION=0 when compiling for
debug (DEBUG=1).
The storage space of the advertisement name is not declared static, leading
to a random advertisement name. This commit fixes the issue by declaring
it static.
The Bluetooth link gets disconnected when connecting from a PC after 30-40
seconds. This commit adds handling of the data length update request. The
data length parameter pointer is set to NULL in the reply, letting the
SoftDevice automatically set values and use them in the data length update
procedure.
mp_keyboard_interrupt() triggers a compiler error because the function is
implicitly declared. This commit adds "py/runtime.h" to the includes.
Fixes issue #5732.
Changes are:
- The default manifest.py is moved to the variants directory (it's in
"boards" in other ports).
- The coverage variant now uses a custom manifest in its variant directory
to add frzmpy/frzstr.
- The frzmpy/frzstr tests are moved to variants/coverage/.
Polling mode will cause failures with the mass-erase command due to USB
timeouts, because the USB IRQs are not being serviced. Swiching from
polling to IRQ mode fixes this because the USB IRQs can be serviced between
page erases.
Note that when the flash is being programmed or erased the MCU is halted
and cannot respond to USB IRQs, because mboot runs from flash, as opposed
to the built-in bootloader which is in system ROM. But the maximum delay
in responding to an IRQ is the time taken to erase a single page, about
100ms for large pages, and that is short enough that the USB does not
timeout on the host side.
Recent tests have shown that in the current mboot code IRQ mode is pretty
much the same speed as polling mode (within timing error), code size is
slightly reduced in IRQ mode, and IRQ mode idles at about half of the power
consumption as polling mode.
This is treated more like a "delay before continuing" in the spec and
official tools and does not appear to be really needed. In particular,
downloading firmware is much slower with non-zero timeouts because the host
must pause by the timeout between sending each DFU_GETSTATUS to poll for
download/erase complete.
Supports hard and soft interrupts. In the current implementation, soft
interrupt callbacks will only be called when the VM is executing, ie they
will not be called during a blocking kernel call like k_msleep. And the
behaviour of hard interrupt callbacks will depend on the underlying device,
as well as the amount of ISR stack space.
Soft and hard interrupts tested on frdm_k64f and nucleo_f767zi boards.
Signed-off-by: Damien George <damien@micropython.org>
The implementation internally uses sector erase to wipe everything except
the sector(s) that mboot lives in (by erasing starting from
APPLICATION_ADDR).
The erase command can take some time (eg an STM32F765 with 2MB of flash
takes 8 to 10 seconds). This time is normally enough to make pydfu.py fail
with a timeout. The DFU standard includes a mechanism for the DFU device
to request a longer timeout as part of the get-status response just before
starting an operation. This timeout functionality has been implemented
here.
Before this commit the USB VCP TX ring-buffer used the basic implementation
where it can only be filled to a maximum of buffer size-1. For a 1024 size
buffer this means the largest packet that can be sent is 1023. Once a
packet of this size is sent the next byte copied in goes to the final byte
in the buffer, so must be sent as a 1 byte packet before the read pointer
can be wrapped around to the beginning. So in large streaming transfers,
watching the USB sniffer you basically get alternating 1023 byte packets
then 1 byte packets.
This commit changes the ring-buffer implementation to a scheme that doesn't
have the full-size limitation, and the USB VCP driver can now achieve a
constant stream of full-sized packets. This scheme introduces a
restriction on the size of the buffer: it must be a power of 2, and the
maximum size is half of the size of the index (in this case the index is
16-bit, so the maximum size would be 32767 bytes rounded to 16384 for a
power-of-2). But this is not a big limitation because the size of the
ring-buffer prior to this commit was restricted to powers of 2 because it
was using a mask-based method to wrap the indices.
For an explanation of the new scheme see
https://www.snellman.net/blog/archive/2016-12-13-ring-buffers/
The RX buffer could likely do with a similar change, though as it's not
read from in chunks like the TX buffer it doesn't present the same issue,
all that's lost is one byte capacity of the buffer.
USB VCP TX throughput is improved by this change, potentially doubling the
speed in certain cases.
By passing through the I2C instance to the application callbacks, the
application can implement multiple I2C slave devices on different
peripherals (eg I2C1 and I2C2).
This commit also adds a proper rw argument to i2c_slave_process_addr_match
for F7/H7/WB MCUs, and enables the i2c_slave_process_tx_end callback.
Mboot is also updated for these changes.
Signed-off-by: Damien George <damien@micropython.org>
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
This commit factors the code for files and streaming to separate source
files (vfs_fat.c and gzstream.c respectively) and introduces an abstract
gzstream interface to make it easier to plug in different filesystems.
Signed-off-by: Damien George <damien@micropython.org>
There's no need to do a directory listing to search for the given firmware
filename, it just takes extra time and code size. Instead this commit
changes it so that the requested firmware file is opened immediately and
will abort if the file couldn't be opened. This also allows to specify
files in a directory.
Signed-off-by: Damien George <damien@micropython.org>
Previously, if FAT was not enabled but LFS1/2 was then MICROPY_PY_IO_FILEIO
would be disabled and file binary-mode was not supported.
Signed-off-by: Damien George <damien@micropython.org>
Commit 8675858465 switched to using the CMSIS
provided SystemInit function which sets VTOR to 0x00000000 (previously it
was 0x08000000). A VTOR of 0x00000000 will be correct on some MCUs but not
on others where the built-in bootloader is remapped to this address, via
__HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH().
To make sure mboot has the correct vector table, this commit explicitly
sets VTOR to the correct value of 0x08000000.
Signed-off-by: Damien George <damien@micropython.org>
There's no need to duplicate this functionality in mboot, the code provided
in stm32lib/CMSIS does the same thing and makes it easier to support other
MCU series.
Signed-off-by: Damien George <damien@micropython.org>
The flash functions in ports/stm32/flash.c are almost identical to those in
ports/stm32/mboot/main.c, so remove the duplicated code in mboot and use
instead the main stm32 code. This also allows supporting other MCU series.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes the low-level flash C functions usable by code other than
flashbdev.c (eg by mboot). Changes in this commit are:
- flash_erase() and flash_write() now return an errno error code, a
negative value on error.
- flash_erase() now automatically locks the flash, as well as unlocking it.
- flash_write() now automatically unlocks the flash, as well as locking it.
- flashbdev.c is modified for the above changes.
Signed-off-by: Damien George <damien@micropython.org>
irq.h is included by py/mphal.h but it's better to be explicit, eg if mboot
uses powerctrlboot.c.
Signed-off-by: Damien George <damien@micropython.org>
The irq.h file now just provides low-level IRQ definitions and priorities.
All Python binding definitions are moved to modmachine.h, with some
renaming of pyb -> machine, and also the machine_idle definition (was
pyb_wfi) is moved to modmachine.c.
The cc3200 and teensy ports are updated to build with these changes.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise the RMT will repeat pulses when using loop(True). This repeating
is due to a bug in the IDF which will be fixed in an upcoming release, but
for now the accepted workaround is to swap these calls, which should still
work in the fixed version of the IDF.
Fixes issue #6167.
With only `sp_func_proto_paren = remove` set there are some cases where
uncrustify misses removing a space between the function name and the
opening '('. This sets all of the related options to `force` as well.
There are a maximum of 8 USB endpoints and each has 2 buffer slots
(in/out). This commit add support for up to 8 endpoints and adds FIFO
configuration for USB profiles with 2xVCP on MCUs that have device-only USB
peripherals.
Tested on NUCLEO_WB55 in 2xVCP, 2xVCP+MSC and 2xVCP+MSC+HID mode.
Signed-off-by: Damien George <damien@micropython.org>
The ESP32 RMT peripheral has hardware support for a carrier frequency, and
this commit exposes it to Python with the keyword arguments carrier_freq
and carrier_duty_percent in the constructor. Example usage:
r = esp32.RMT(0, pin=Pin(2), clock_div=80, carrier_freq=38000, carrier_duty_percent=50)
Zephyr renamed CONFIG_FLOAT to CONFIG_FPU to better reflect its semantics
of enabling the hardware floating point unit (FPU) rather than enabling
toolchain-level floating point support (i.e., software floating point for
FPU-less socs).
Zephyr deprecated and then removed its stack_analyze function because it
was unsafe. Use the new zephyr thread analyzer instead and rename the
MicroPython function to zephyr.thread_analyze() to be more consistent with
the implementation.
Tested on mimxrt1050_evk.
The output now looks like this:
>>> zephyr.thread_analyze()
Thread analyze:
80004ff4 : unused 400 usage 112 / 512 (21 %)
rx_workq : unused 1320 usage 180 / 1500 (12 %)
tx_workq : unused 992 usage 208 / 1200 (17 %)
net_mgmt : unused 656 usage 112 / 768 (14 %)
sysworkq : unused 564 usage 460 / 1024 (44 %)
idle : unused 256 usage 64 / 320 (20 %)
main : unused 2952 usage 1784 / 4736 (37 %)
Sending more than 64 bytes to the USB CDC endpoint in HS mode will lead to
a hard crash. This commit fixes the issue, although there may be a better
fix from upstream TinyUSB in the future.
With this commit the code should work correctly regardless of the size of
StackType_t (it's actually 1 byte in size for the esp32's custom FreeRTOS).
Fixes issue #6072.
This commit implements an LED class with rudimentary parts of a pin C API
to support it. The LED class does not yet support setting an intensity.
This LED class is put in the machine module for the time being, until a
better place is found.
One LED is supported on TEENSY40 and MIMXRT1010_EVK boards.
Changes are:
- string0 is no longer built when building for host as the target, because
it'll be provided by the system libc and may in some cases clash with the
system one (eg on OSX).
- mp_int_t/mp_uint_t are defined in terms of intptr_t/uintptr_t to support
both 32-bit and 64-bit builds.
- Configuration values which are the default in py/mpconfig.h are removed
from mpconfigport.h to make the configuration a bit more minimal, eg as
a better starting point for new ports.
Microwatt may have firmware that places data in r3, which was used to
detect microwatt vs powernv. This breaks the existing probing of the UART
type in this powerpc port.
Instead build only the appropriate UART into the firmware, selected by
passing the option UART=potato or UART=lpc_serial to the Makefile.
A future enhancement would be to parse the device tree and configure
MicroPython based on the settings.
The code previously called rtc_get_reset_reason which is a "raw" reset
cause. The ESP-IDF massages that for the proper reset cause available from
esp_reset_reason.
Fixes issue #5134.
Add configuration which otherwise has to be set via the UI so the file is
more self-contained, and remove configuration which is not needed because
it's the same as the default. The major change here is that for a while
now Appveyor has been using Visual Studio 2015 by default while we still
want to support 2013.
Older implementations deal with infinity/negative zero incorrectly. This
commit adds generic fixes that can be enabled by any port that needs them,
along with new tests cases.
The linker script was included in the "$^" inputs, causing the build to
fail:
LINK build/firmware.elf
powerpc64le-linux-gnu-ld: error: linker script file 'powerpc.lds' appears multiple times
As a fix the linker script is left as a dependency of the elf, but only the
object files are linked.
The PWM driver uses a double buffer for the PWM timing array, one in
current use and the other one to update when changing duty parameters.
The issue was that once the duty parameters were changed the updated buffer
was applied immediately without synchronising to the start of the PWM
period. By moving the buffer toggling/swapping to the interrupt when the
cycle is done there are no more glitches.
Commit 6cea369b89 updated the TinyUSB
submodule to a version based on nrfx v2.0.0. This commit updates the nrf
port to work with the latest TinyUSB and nrfx v2.0.0.
Because it can confuse older versions of gcc. Instead use the correct
instruction for Thumb vs Thumb-2 (sub vs subs) so the assembler emits the
2-byte instruction.
Related to commit 1aa9ff9141.
Prior to e0905e85a7 it was possible to
disable btree support on build. This patch allows to configure btree
support on make again and also the two new introduced options for FAT and
LFS2 filesystems.
This commit allows the user to set/get the GAP device name used by service
0x1800, characteristic 0x2a00. The usage is:
BLE.config(gap_name="myname")
print(BLE.config("gap_name"))
As part of this change the compile-time setting
MICROPY_PY_BLUETOOTH_DEFAULT_NAME is renamed to
MICROPY_PY_BLUETOOTH_DEFAULT_GAP_NAME to emphasise its link to GAP and this
new "gap_name" config value. And the default value of this for the NimBLE
bindings is changed from "PYBD" to "MPY NIMBLE" to be more generic.
This commit fixes the behaviour of socket.getaddrinfo on the ESP32 so it
raises an OSError when the name resolution fails instead of returning a []
or a resolution for 0.0.0.0.
Tests are added (generic and ESP32-specific) to verify behaviour consistent
with CPython, modulo the different types of exceptions per MicroPython
documentation.
The ones that are moved out of iRAM should not need to be there, because
either they call functions in iROM (eg mp_hal_stdout_tx_str), or they are
only ever called from a function in iROM and not from an interrupt (eg
ets_esf_free_bufs).
This frees up about 800 bytes of iRAM.
The zephyr build system supports merging application-level board
configurations, so there is no need to reproduce this functionality in
MicroPython.
If CONF_FILE is not explicitly set, then the zephyr build system looks for
prj.conf in the application directory. Therefore we rename the MicroPython
prj_base.conf to prj.conf.
Furthermore, if the zephyr build system finds boards/$(BOARD).conf in the
application directory, it merges that configuration with prj.conf.
Therefore we rename all the MicroPython board .conf files and move them
into a boards/ directory.
The minimal configuration, prj_minimal.conf, is left in the application
directory because it is used as an explicitly set CONF_FILE in
make-minimal.
This commit adds several small items to improve the support for OTA
updates on an esp32:
- a partition table for 4MB flash modules that has two OTA partitions ready
to go to do updates
- a GENERIC_OTA board that uses that partition table and that enables
automatic roll-back in the bootloader
- a new esp32.Partition.mark_app_valid_cancel_rollback() class-method to
signal that the boot is successful and should not be rolled back at the
next reset
- an automated test for doing an OTA update
- documentation updates
GPIO interrupts can occur when the flash ROM cache is in use and so the
GPIO interrupt handler must be in iRAM. This commit moves the handler to
iRAM, and also moves mp_sched_schedule to iRAM which is called by
pin_intr_handler.
As part of this fix the Pin class can no longer support hard=True in the
Pin.irq() method, because the VM and runtime are too big to put in iRAM.
Fixes#5714.
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port. This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.
Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.
The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
But only when bluetooth is enabled, i.e. if building the dev or coverage
variants, and we have libusb available.
Update travis to match, i.e. specify the variant when doing
`make submodules`.
This commit adds full support to the unix port for Bluetooth using the
common extmod/modbluetooth Python bindings. This uses the libusb HCI
transport, which supports many common USB BT adaptors.
This change is made for two reasons:
1. A 3rd-party library (eg berkeley-db-1.xx, axtls) may use the system
provided errno for certain errors, and yet MicroPython stream objects
that it calls will be using the internal mp_stream_errno. So if the
library returns an error it is not known whether the corresponding errno
code is stored in the system errno or mp_stream_errno. Using the system
errno in all cases (eg in the mp_stream_posix_XXX wrappers) fixes this
ambiguity.
2. For systems that have threading the system-provided errno should always
be used because the errno value is thread-local.
For systems that do not have an errno, the new lib/embed/__errno.c file is
provided.
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
This commit consolidates a number of check_esp_err functions that check
whether an ESP-IDF return code is OK and raises an exception if not. The
exception raised is an OSError with the error code as the first argument
(negative if it's ESP-IDF specific) and the ESP-IDF error string as the
second argument.
This commit also fixes esp32.Partition.set_boot to use check_esp_err, and
uses that function for a unit test.
This commit adds an idf_heap_info(capabilities) method to the esp32 module
which returns info about the ESP-IDF heaps. It's useful to get a bit of a
picture of what's going on when code fails because ESP-IDF can't allocate
memory anymore. Includes documentation and a test.
In mboot, the ability to override the USB vendor/product id's was added
back in 5688c9ba09. However, when the main
firmware is turned into a DFU file the default VID/PID are used there.
pydfu.py doesn't care about this but dfu-util does and prevents its use
when the VID/PID don't match.
This commit exposes BOOTLOADER_DFU_USB_VID/PID as make variables, for use
on either command line or mpconfigboard.mk, to set VID/PID in both mboot
and DFU files.
Add -Wdouble-promotion and -Wfloat-conversion for most ports to ban out
implicit floating point conversions, and add extra Travis builds using
MICROPY_FLOAT_IMPL_FLOAT to uncover warnings which weren't found
previously. For the unix port -Wsign-comparison is added as well but only
there since only clang supports this but gcc doesn't.
Initially some of these were found building the unix coverage variant on
MacOS because that build uses clang and has -Wdouble-promotion enabled, and
clang performs more vigorous promotion checks than gcc. Additionally the
codebase has been compiled with clang and msvc (the latter with warning
level 3), and with MICROPY_FLOAT_IMPL_FLOAT to find the rest of the
conversions.
Fixes are implemented either as explicit casts, or by using the correct
type, or by using one of the utility functions to handle floating point
casting; these have been moved from nativeglue.c to the public API.
Now that error string compression is supported it's more important to have
consistent error string formatting (eg all lowercase English words,
consistent contractions). This commit cleans up some of the strings to
make them more consistent.
This macro is used to implement global serialisation, typically by
disabling IRQs. On the unix port, if threading is enabled, use the
existing thread mutex (that protects the thread list structure) for this
purpose. Other places in the code (eg the scheduler) assume this macro
will provide serialisation.
Based on eg 1e6fd9f2b4, it's understood that
the intention for unix builds is that regular builds disable assert, but
the coverage build should set -O0 and enable asserts.
It looks like this didn't work (even before variants were introduced, eg at
v1.11) -- coverage always built with -Os and -DNDEBUG.
This commit makes it possible for variants to have finer-grained control
over COPT flags, and enables assert() and -O0 on coverage builds.
Other variants already match the defaults so they have been updated.
TimeoutError was added back in 077812b2ab for
the cc3200 port. In f522849a4d the cc3200
port enabled use of it in the socket module aliased to socket.timeout. So
it was never added to the builtins. Then it was replaced by
OSError(ETIMEDOUT) in 047af9b10b.
The esp32 port enables this exception, since the very beginning of that
port, but it could never be accessed because it's not in builtins.
It's being removed: 1) to not encourage its use; 2) because there are a lot
of other OSError subclasses which are not defined at all, and having
TimeoutError is a bit inconsistent.
Note that ports can add anything to the builtins via MICROPY_PORT_BUILTINS.
And they can also define their own exceptions using the
MP_DEFINE_EXCEPTION() macro.
This commit makes all functions and function wrappers in modubinascii.c
STATIC and conditional on the MICROPY_PY_UBINASCII setting, which will
exclude the file from qstr/ compressed-string searching when ubinascii is
not enabled. The now-unused modubinascii.h header file is also removed.
The cc3200 port is updated accordingly to use this module in its entirety
instead of providing its own top-level definition of ubinascii.
This was originally like this because the cc3200 port has its own ubinascii
module which referenced these methods. The plan appeared to be that the
API might diverge (e.g. hardware crc), but this should be done similar to
I2C/SPI via a port-specific handler, rather than the port having its own
definition of the module. Having a centralised module definition also
enforces consistency of the API among ports.
This commit changes the default filesystem type for esp32 to littlefs v2.
This port already enables both VfsFat and VfsLfs2, so either can be used
for the filesystem, and existing systems that use FAT will still work.
This commit changes the esp8266 boards to use littlefs v2 as the
filesystem, rather than FAT. Since the esp8266 doesn't expose the
filesystem to the PC over USB there's no strong reason to keep it as FAT.
Littlefs is smaller in code size, is more efficient in use of flash to
store data, is resilient over power failure, and using it saves about 4k of
heap RAM, which can now be used for other things.
This is a backwards incompatible change because all existing esp8266 boards
will need to update their filesystem after installing new firmware (eg
backup old files, install firmware, restore files to new filesystem).
As part of this commit the memory layout of the default board (GENERIC) has
changed. It now allocates all 1M of memory-mapped flash to the firmware,
so the filesystem area starts at the 2M point. This is done to allow more
frozen bytecode to be stored in the 1M of memory-mapped flash. This
requires an esp8266 module with 2M or more of flash to work, so a new board
called GENERIC_1M is added which has the old memory-mapping (but still
changed to use littlefs for the filesystem).
In summary there are now 3 esp8266 board definitions:
- GENERIC_512K: for 512k modules, doesn't have a filesystem.
- GENERIC_1M: for 1M modules, 572k for firmware+frozen code, 396k for
filesystem (littlefs).
- GENERIC: for 2M (or greater) modules, 968k for firmware+frozen code,
1M+ for filesystem (littlefs), FAT driver also included in firmware for
use on, eg, external SD cards.
Following up to 5e6cee07ab, some systems (eg
FreeBSD 12.0 64-bit) will crash if the stack-overflow margin is too small.
It seems the margin of 8192 bytes (or thereabouts) is always needed. This
commit adds this much margin if the requested stack size is too small.
Fixes issue #5824.
These were found by buiding the unix coverage variant on macOS (so clang
compiler). Mostly, these are fixing implicit cast of float/double to
mp_float_t which is one of those two and one mp_int_t to size_t fix for
good measure.
These are mainly used by the previous version of uasyncio which is now
replaced by a newer version, with built-in C module _uasyncio. Saves about
1300 bytes of flash.
https://www.python.org/dev/peps/pep-0475/
This implements something similar to PEP 475 on the unix port, and for the
VfsPosix class.
There are a few differences from the CPython implementation:
- Since we call mp_handle_pending() between any ENITR's, additional
functions could be called if MICROPY_ENABLE_SCHEDULER is enabled, not
just signal handlers.
- CPython only handles signal on the main thread, so other threads will
raise InterruptedError instead of retrying. On MicroPython,
mp_handle_pending() will currently raise exceptions on any thread.
A new macro MP_HAL_RETRY_SYSCALL is introduced to reduce duplicated code
and ensure that all instances behave the same. This will also allow other
ports that use POSIX-like system calls (and use, eg, VfsPosix) to provide
their own implementation if needed.
The stack size adjustment for detecting stack overflow in threads was not
taking into account that the requested stack size could be <= 8k, in which
case the subtraction would overflow. This is fixed in this commit by
ensuring that the adjustment can't be more than the available size.
This fixes the test tests/thread/thread_stacksize1.py which sometimes
crashes with a segmentation fault because of an uncaught NLR jump, which is
a "maximum recursion depth exceeded" exception.
Suggested-by: @dpgeorge
To enable lazy loading of submodules (among other things), which is very
useful for MicroPython libraries that want to have optional subcomponents.
Disabled explicitly on minimal ports.
This function is not used by the core but having it as part of the build
allows it to be used by user C modules, or board extensions. The linker
won't include it in the final firmware if it remains unused.
This removes the port-specific definition of MP_PLAT_PRINT_STRN on the
windows port, so that the default mp_hal_stdout_tx_strn_cooked() is always
used. This fixes releasing the GIL during the call to write() (this was
missed in bc3499f010).
Also, mp_hal_dupterm_tx_strn() was defined but never used anywhere so it is
safe to delete it.
This removes the port-specific definition of MP_PLAT_PRINT_STRN on the unix
port. Since fee7e5617f this is no longer a
single function call so we are not really optimising anything over using
the default definition of MP_PLAT_PRINT_STRN which calls
mp_hal_stdout_tx_strn_cooked().
Zephyr v2.2 reworked its gpio api to support linux device tree bindings and
pin logical levels. This commit updates the zephyr port's machine.Pin
class to replace the deprecated gpio api calls with the new supported gpio
api. This resolves several build warnings.
Tested on frdm_k64f and mimxrt1050_evk boards.
The "led" argument is always a pointer to the GPIO port, or'd with the pin
that the LED is on, so testing that it is "1" is unnecessary. The type of
"led" is also changed to uint32_t so it can properly hold a 32-bit pointer.
Updating the LED0 state from systick handler ensures LED0 is always
consistent with its flash rate regardless of other processing going on in
either interrupts or main. This improves the visible stability of the
bootloader, rather than LED0 flashing somewhat randomly at times.
This commit also changes the LED0 flash rate depending on the current state
of DFU, giving slightly more visual feedback on what the device is doing.
Adds support in the zephyr port to execute main.py if the file system is
enabled and the file exists. Existing support for executing a main.py
frozen module is preserved, since pyexec_file_if_exists() works just
like pyexec_frozen_module() if there's no vfs.
Enables the zephyr usb device stack and mass storage class on the
mimxrt1050_evk board. The mass storage class is backed by the sdhc disk
access driver, so it's now possible to browse and modify the contents of
the SD card from a USB host (your PC). This is in preparation to support
writing a main.py script to the SD card, and then executing it after the
next reset.
Adds support in the zephyr port to mount a file system if a block device
(sdhc disk access or flash area) is available. The mount point is either
"/sd" or "/flash" depending on the type of block device.
Tested with an sdhc disk access block device and fatfs on the
mimxrt1050_evk board.
Tested with a flash area block device and littlefs on the reel_board.
This commit adds micropython.heap_locked() which returns the current
lock-depth of the heap, and can be used by Python code to check if the heap
is locked or not. This new function is configured via
MICROPY_PY_MICROPYTHON_HEAP_LOCKED and is disabled by default.
This commit also changes the return value of micropython.heap_unlock() so
it returns the current lock-depth as well.
This is an extremely minimal port to the NXP i.MX RT, in the style of the
SAMD port It's largely based on the TinyUSB mimxrt implementation, using
the NXP SDK. It currently supports the Teensy 4.0 board with a REPL over
the USB-VCP interface.
This commit also adds the NXP SDK submodule (also from TinyUSB) to
lib/nxp_driver.
Note: if you already have the tinyusb submodule initialized recursively you
will need to run the following as the tinyusb sub-submodules have been
rearranged (upstream):
git submodule deinit lib/tinyusb
rm -rf .git/modules/lib/tinyusb
git submodule update --init lib/tinyusb
This makes a cleaner separation between the: driver, HCI UART and BT stack.
Also updated the naming to be more consistent (mp_bluetooth_hci_*).
Work done in collaboration with Jim Mussared aka @jimmo.
Move extmod/modbluetooth_nimble.* to extmod/nimble. And move common
Makefile lines to extmod/nimble/nimble.mk (which was previously only used
by stm32). This allows (upcoming) btstack to follow a similar structure.
Work done in collaboration with Jim Mussared aka @jimmo.
sys.stdout.flush() is needed on CPython to flush the output, and the change
in this commit makes such an expression also work on MicroPython (although
MicroPython doesn't actual need to do any flushing).
This string is recognised by uncrustify, to disable formatting in the
region marked by these comments. This is necessary in the qstrdef*.h files
to prevent modification of the strings within the Q(...). In other places
it is used to prevent excessive reformatting that would make the code less
readable.
If the built-in input() is enabled (which it is by default) then it needs
some form of readline, so supply it with one when MICROPY_USE_READLINE=0.
Fixes issue #5658.
This changes the signal used to trigger garbage collection from SIGUSR1 to
SIGRTMIN + 5. SIGUSR1 is quite common compared to SIGRTMIN (measured by
google search results) and is more likely to conflict with libraries that
may use the same signal.
POSIX specifies that there are at least 8 real-time signal so 5 was chosen
as a "random" number to further avoid potential conflict with libraries
that may use SIGRTMIN or SIGRTMAX.
Also, if we ever have a `usignal` module, it would be nice to leave SIGUSR1
and SIGUSR2 free for user programs.
The "random" module no longer uses the hardware RNG (the extmod version of
this module has a pseudo-random number generator), so the config option
MICROPY_PY_RANDOM_HW_RNG is no longer meaningful. This commit replaces it
with MICROPY_HW_ENABLE_RNG, which controls whether the hardware RNG is
included in the build.
The install target is current broken when PROG is used to override the
default executable name. This fixes it by removing the redundant TARGET
variable and uses PROG directly instead.
The install and uninstall targets are also moved to the common unix
Makefile so that all variants can be installed in the same way.
Currently it is not possible to override PREFIX when installing micropython
using the makefile. It is common practice to be able to run something like
this:
$ make install PREFIX=/usr DESTDIR=/tmp/staging
This fixes such usage.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX. It also reduces code size by a
small amount on some ports.
The default value for MICROPYPATH used in unix/main.c is
"~/.micropython/lib:/usr/lib/micropython" which has 2 problems when used in
the Windows port:
- it has a ':' as path separator but the port uses ';' so the entire string
is effectively discarded since it gets interpreted as a single path which
doesn't exist
- /usr/lib/micropython is not a valid path in a standard Windows
environment
Override the value with a suitable default.
If the exception doesn't need printf-style formatting then calling
mp_raise_msg is more efficient. Also shorten exception messages to match
style in core and other ports.
It's not needed. The C integer implicit promotion rules mean that the
uint8_t of the incoming character is promoted to a (signed) int, matching
the type of interrupt_char. Thus the uint8_t incoming character can never
be equal to -1 (the value of interrupt_char that indicate that interruption
is disabled).
The mp_keyboard_interrupt() function does exactly what is needed here, and
using it gets ctrl-C working when MICROPY_ENABLE_SCHEDULER is enabled on
these ports (and MICROPY_ASYNC_KBD_INTR is disabled).
This is a more logical place to clear the KeyboardInterrupt traceback,
right before it is set as a pending exception. The clearing is also
optimised from a function call to a simple store of NULL.
It was originally in IRAM due to the linker script specification, but
since the function moved from lib/utils/interrupt_char.c to py/scheduler.c
it needs to be put back in IRAM.
This function is tightly coupled to the state and behaviour of the
scheduler, and is a core part of the runtime: to schedule a pending
exception. So move it there.
Pending exceptions would otherwise be handled later on where there may not
be an NLR handler in place.
A similar fix is also made to the unix port's REPL handler.
Fixes issues #4921 and #5488.
Previous behaviour is when this argument is set to "true", in which case
the function will raise any pending exception. Setting it to "false" will
cancel any pending exception.
Enables the littlefs (v1 and v2) filesystems in the zephyr port.
Example usage with the internal flash on the reel_board or the
rv32m1_vega_ri5cy board:
import os
from zephyr import FlashArea
bdev = FlashArea(FlashArea.STORAGE, 4096)
os.VfsLfs2.mkfs(bdev)
os.mount(bdev, '/flash')
with open('/flash/hello.txt','w') as f:
f.write('Hello world')
print(open('/flash/hello.txt').read())
Things get a little trickier with the frdm_k64f due to the micropython
application spilling into the default flash storage partition defined
for this board. The zephyr build system doesn't enforce the flash
partitioning when mcuboot is not enabled (which it is not for
micropython). For now we can demonstrate that the littlefs filesystem
works on frdm_k64f by constructing the FlashArea block device on the
mcuboot scratch partition instead of the storage partition. Do this by
replacing the FlashArea.STORAGE constant above with the value 4.
Introduces a new zephyr.FlashArea class that uses the zephyr flash map
api to implement the uos.AbstractBlockDev protocol. The flash driver is
enabled on the frdm_k64f board, reel_board, and rv32m1_vega_ri5cy board.
The standard and extended block device protocols are both supported,
therefore this class can be used with file systems like littlefs which
require the extended interface.
Enables the fatfs filesystem in the zephyr port.
Example usage with an SD card on the mimxrt1050_evk board:
import zephyr, os
bdev = zephyr.DiskAccess('SDHC')
os.VfsFat.mkfs(bdev)
os.mount(bdev, '/sd')
with open('/sd/hello.txt','w') as f:
f.write('Hello world')
print(open('/sd/hello.txt').read())
Introduces a new zephyr.DiskAccess class that uses the zephyr disk
access api to implement the uos.AbstractBlockDev protocol. This can be
used with any type of zephyr disk access driver, which currently
includes SDHC, RAM, and FLASH implementations. The SDHC driver is
enabled on the mimxrt1050_evk board.
Only the standard block device protocol (without the offset parameter)
can be supported with the zephyr disk access api, therefore this class
cannot be used with file systems like littlefs which require the
extended interface. In the future it may be possible to implement the
extended interface in a new class using the zephyr flash api.
CPython also has os.environ, which should be used instead of os.getenv()
due to caching in the os.environ mapping. But for MicroPython it makes
sense to only implement the basic underlying methods, ie getenv/putenv/
unsetenv.
This adds a -h option to print the usage help text and adds a new, shorter
error message that is printed when invalid arguments are given. This
behaviour follows CPython (and other tools) more closely.
This commit modifies the usage() function to only print the -v option help
text when MICROPY_DEBUG_PRINTERS is enabled. The -v option requires this
build option to be enabled for it to have any effect.
The usage text is also modified to show the -i and -m options, and also
show that running a command, module or file are mutually exclusive.
This adds support for a MICROPYINSPECT environment variable that works
exactly like PYTHONINSPECT; per CPython docs:
If this is set to a non-empty string it is equivalent to specifying the
-i option.
This variable can also be modified by Python code using os.environ to
force inspect mode on program termination.
Zephyr removed the build target syscall_macros_h_target in commit
f4adf107f31674eb20881531900ff092cc40c07f. Removes reference from
MicroPython to fix build errors in the zephyr port.
This change is not compatible with zephyr v2.1 or earlier. It will be
compatible with Zephyr v2.2 when released.
The SYS_CLOCK_HW_CYCLES_TO_NS macro was deprecated in zephyr commit
8892406c1de21bd5de5877f39099e3663a5f3af1. This commit updates MicroPython
to use the new k_cyc_to_ns_floor64 api and fix build warnings in the zephyr
port.
This change is compatible with Zephyr v2.1 and later.
Zephyr restructured its includes in v2.0 and removed compatibility shims
after two releases in commit 1342dadc365ee22199e51779185899ddf7478686.
Updates include paths in MicroPython accordingly to fix build errors in
the zephyr port.
These changes are compatible with Zephyr v2.0 and later.
When stdout is redirected it is useful to have errors printed to stderr
instead of being redirected.
mp_stderr_print() can't be used in these two instances since the
MicroPython runtime is not running so we use fprintf(stderr) instead.
The ability to change the host is a frequently requested feature, so
explicitly document how it can be achieved using the existing code.
See issues #2121, #4385, #4622, #5122, #5536.
This commit improves pllvalues.py to generate PLL values for H7 MCUs that
are valid (VCO in and out are in range) and extend for the entire range of
SYSCLK values up to 400MHz (up to 480MHz is currently unsupported).
This board now has the following 3 build configurations:
- mboot + external QSPI in XIP mode + internal filesystem
- mboot + external QSPI with filesystem (the default)
- no mboot + external QSPI with filesystem
