Commit Graph

1066 Commits

Author SHA1 Message Date
Andrew Leech 40006813c3 stm32/flash: Update flash_get_sector_info to return -1 on invalid addr.
So the caller can tell when an invalid address is used and can take
appropriate action.
2020-06-30 21:24:28 +10:00
Andrew Leech 8bbaa20227 stm32/mboot: Implement DFU mass erase.
The implementation internally uses sector erase to wipe everything except
the sector(s) that mboot lives in (by erasing starting from
APPLICATION_ADDR).

The erase command can take some time (eg an STM32F765 with 2MB of flash
takes 8 to 10 seconds).  This time is normally enough to make pydfu.py fail
with a timeout.  The DFU standard includes a mechanism for the DFU device
to request a longer timeout as part of the get-status response just before
starting an operation.  This timeout functionality has been implemented
here.
2020-06-30 21:22:21 +10:00
Damien George 048a1d675d stm32/timer: Properly initialise timer deadtime/brk on WB MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-29 17:35:42 +10:00
Andrew Leech e4fcd216e0 stm32/usbd_cdc_interface: Remove full==size-1 limitation on tx ringbuf.
Before this commit the USB VCP TX ring-buffer used the basic implementation
where it can only be filled to a maximum of buffer size-1.  For a 1024 size
buffer this means the largest packet that can be sent is 1023.  Once a
packet of this size is sent the next byte copied in goes to the final byte
in the buffer, so must be sent as a 1 byte packet before the read pointer
can be wrapped around to the beginning.  So in large streaming transfers,
watching the USB sniffer you basically get alternating 1023 byte packets
then 1 byte packets.

This commit changes the ring-buffer implementation to a scheme that doesn't
have the full-size limitation, and the USB VCP driver can now achieve a
constant stream of full-sized packets.  This scheme introduces a
restriction on the size of the buffer: it must be a power of 2, and the
maximum size is half of the size of the index (in this case the index is
16-bit, so the maximum size would be 32767 bytes rounded to 16384 for a
power-of-2).  But this is not a big limitation because the size of the
ring-buffer prior to this commit was restricted to powers of 2 because it
was using a mask-based method to wrap the indices.

For an explanation of the new scheme see
https://www.snellman.net/blog/archive/2016-12-13-ring-buffers/

The RX buffer could likely do with a similar change, though as it's not
read from in chunks like the TX buffer it doesn't present the same issue,
all that's lost is one byte capacity of the buffer.

USB VCP TX throughput is improved by this change, potentially doubling the
speed in certain cases.
2020-06-29 17:21:37 +10:00
Damien George 137df81757 stm32/i2cslave: Pass I2C instance to callbacks to support multi I2Cs.
By passing through the I2C instance to the application callbacks, the
application can implement multiple I2C slave devices on different
peripherals (eg I2C1 and I2C2).

This commit also adds a proper rw argument to i2c_slave_process_addr_match
for F7/H7/WB MCUs, and enables the i2c_slave_process_tx_end callback.
Mboot is also updated for these changes.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-26 23:56:45 +10:00
Damien George 0a8ce0d568 stm32/mboot: Update README to describe WB and littlefs support.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-26 21:26:06 +10:00
Damien George 67fd58bbd2 stm32/mboot: Add support for littlefs.
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:

    #define MBOOT_VFS_FAT (1)

Signed-off-by: Damien George <damien@micropython.org>
2020-06-26 21:17:02 +10:00
Damien George 390f32922d stm32/mboot: Decouple stream, filesystem and top-level loading code.
This commit factors the code for files and streaming to separate source
files (vfs_fat.c and gzstream.c respectively) and introduces an abstract
gzstream interface to make it easier to plug in different filesystems.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-26 21:15:30 +10:00
Damien George 763bd448a4 stm32/mboot: Don't search for firmware on FS, just attempt to open it.
There's no need to do a directory listing to search for the given firmware
filename, it just takes extra time and code size.  Instead this commit
changes it so that the requested firmware file is opened immediately and
will abort if the file couldn't be opened.  This also allows to specify
files in a directory.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-26 21:11:03 +10:00
Damien George 717b5073aa stm32/boards: Enable LFS2 on PYBD_SF3 and PYBD_SF6.
This was missed in commit 120368ba1a

Signed-off-by: Damien George <damien@micropython.org>
2020-06-25 16:32:48 +10:00
Damien George c5af3217d9 stm32/timer: Support TIM1 on WB MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-25 16:32:48 +10:00
Damien George eb9850ef6c stm32/mpconfigport.h: Enable PY_IO_FILEIO when any VFS is enabled.
Previously, if FAT was not enabled but LFS1/2 was then MICROPY_PY_IO_FILEIO
would be disabled and file binary-mode was not supported.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-25 16:32:48 +10:00
Damien George b4dc4c5b9a stm32/mboot: Use additional CFLAGS to compile string0.c.
This is the same as a902b69dd5 but applied to
mboot's Makefile.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-23 14:00:16 +10:00
Damien George 81a7293ed6 stm32/mboot: Set VTOR on start up to ensure it has the correct value.
Commit 8675858465 switched to using the CMSIS
provided SystemInit function which sets VTOR to 0x00000000 (previously it
was 0x08000000).  A VTOR of 0x00000000 will be correct on some MCUs but not
on others where the built-in bootloader is remapped to this address, via
__HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH().

To make sure mboot has the correct vector table, this commit explicitly
sets VTOR to the correct value of 0x08000000.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-23 13:56:20 +10:00
Damien George 6f40e6e131 stm32/boards: Add build-time option for NUCLEO_WB55 to use mboot.
As an example of how to use mboot on a WB series MCU.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George 705728369d stm32/mboot: Add support for using mboot with WB MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George 8675858465 stm32/mboot: Use CMSIS system source code for SystemInit function.
There's no need to duplicate this functionality in mboot, the code provided
in stm32lib/CMSIS does the same thing and makes it easier to support other
MCU series.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George a8778c8dc8 stm32/mboot: Use flash routines from main stm32 code rather than custom.
The flash functions in ports/stm32/flash.c are almost identical to those in
ports/stm32/mboot/main.c, so remove the duplicated code in mboot and use
instead the main stm32 code.  This also allows supporting other MCU series.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George 736daebfc8 stm32/flash: Add flash_is_valid_addr, and extend sectors for 2MB F7.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George 4c8a68df6f stm32/i2cslave: Add support for WB MCUs.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George afd47d58ac stm32/flash: Make flash C-API reusable, and funcs return an error code.
This commit makes the low-level flash C functions usable by code other than
flashbdev.c (eg by mboot).  Changes in this commit are:
- flash_erase() and flash_write() now return an errno error code, a
  negative value on error.
- flash_erase() now automatically locks the flash, as well as unlocking it.
- flash_write() now automatically unlocks the flash, as well as locking it.
- flashbdev.c is modified for the above changes.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 14:18:15 +10:00
Damien George ce326699d7 stm32/powerctrlboot: Include irq.h to get definitions of IRQ priorities.
irq.h is included by py/mphal.h but it's better to be explicit, eg if mboot
uses powerctrlboot.c.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 13:47:48 +10:00
Damien George 5f3c2f1fa8 stm32/irq: Clean up irq.h so it does not depend on core uPy defines.
The irq.h file now just provides low-level IRQ definitions and priorities.
All Python binding definitions are moved to modmachine.h, with some
renaming of pyb -> machine, and also the machine_idle definition (was
pyb_wfi) is moved to modmachine.c.

The cc3200 and teensy ports are updated to build with these changes.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-22 13:47:15 +10:00
Damien George ce02d5e348 stm32/boards/NUCLEO_WB55: Add more CPU pins and aliases to SW1/2/3.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-18 10:48:24 +10:00
Damien George 4b5dd012e0 stm32/rfcore: Leave txpower level as default when initialising rfcore.
And provide a convenient API function to change it (currently unused).

Fixes issue #5985.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-17 00:10:29 +10:00
Damien George 289be6b352 stm32/usb: Add support for 2xVCP on L0, L432 and WB MCUs.
There are a maximum of 8 USB endpoints and each has 2 buffer slots
(in/out).  This commit add support for up to 8 endpoints and adds FIFO
configuration for USB profiles with 2xVCP on MCUs that have device-only USB
peripherals.

Tested on NUCLEO_WB55 in 2xVCP, 2xVCP+MSC and 2xVCP+MSC+HID mode.

Signed-off-by: Damien George <damien@micropython.org>
2020-06-17 00:09:42 +10:00
Damien George da99e0f979 stm32/factoryreset: Provide empty create-FS function when FAT disabled.
Signed-off-by: Damien George <damien@micropython.org>
2020-06-17 00:09:37 +10:00
Damien George 2b9900380a stm32/boards/STM32F769DISC: Use macro instead of const for flash size.
So that the flash size can be changed in just one place.  Also remove the
duplicate cache entry.
2020-06-12 10:28:26 +10:00
stinos da71f55e23 stm32/Makefile: Quote libgcc path so spaces are not an issue.
Fixes #3116.
2020-06-02 14:11:08 +10:00
Damien George 246f3f640d stm32/boards/xxx_WB55: Enable pyb.ADC and hardware SPI on WB55 boards.
These features are now supported (although machine.ADC is recommended over
pyb.ADC).
2020-06-02 10:48:49 +10:00
Damien George c8985d52d3 stm32/dma: Add support for DMA on STM32WB, with SPI settings provided. 2020-06-02 10:48:49 +10:00
Damien George 0f7b5cceea stm32/machine_adc: Make setting of ADC1_COMMON->CCR clearer on STM32WB. 2020-06-02 10:48:49 +10:00
Damien George 5210fc51ec stm32/adc: Add support to pyb.ADC for STM32WB MCUs. 2020-06-02 10:48:49 +10:00
Damien George 68d053c66e stm32/modmachine: Allow changing AHB and APB bus frequencies on STM32WB.
For now SYSCLK cannot be changed and must remain at 64MHz.
2020-06-02 10:48:49 +10:00
Damien George 9ae50d22c9 stm32/machine_uart: Allow re-init'ing a static UART object.
Just disallow changing the rxbuf which will be some static RAM (can't free
it and soft-reset would lose any dynamically allocated buffer).
2020-06-01 21:41:54 +10:00
Damien George 88971342b1 stm32/machine_uart: Retain attached-to-repl setting when init'ing UART. 2020-06-01 21:41:50 +10:00
Thomas Roberts 463c0fb2f4 stm32/boards: Add board config for Nucleo-F412ZG development board. 2020-05-15 10:48:48 +10:00
Thomas Roberts d7399679de stm32: Add support for F412 MCUs. 2020-05-15 10:08:30 +10:00
Thorsten von Eicken f385b7bfa8 stm32/README: Reorg DFU flashing instructions with addition for PYBD. 2020-05-11 21:23:41 +10:00
Damien George e2def200bf stm32/boards/PYBD_SF2: Put BTstack library in external QSPI XIP flash.
In the same way the nimble stack is put there.
2020-05-05 20:21:15 +10:00
Jim Mussared 710426024a all: Factor gchelper code to one place and use it for unix & ARM ports.
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port.  This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.

Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.

The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
2020-04-29 23:45:19 +10:00
Jim Mussared 50e44f477b stm32/main: Peform a clean shutdown of btstack on soft reset.
Not just NimBLE.
2020-04-29 16:45:46 +10:00
Jim Mussared 8119ec0765 extmod/modbluetooth: Don't hold atomic section during mp_sched_schedule.
Because, for example, on unix the atomic section isn't re-entrant, and
mp_sched_schedule() will try to re-acquire the atomic section.
2020-04-29 16:45:40 +10:00
Jim Mussared 0da47ecc93 stm32/Makefile: Rename SRC_LIB to LIB_SRC_C to match other ports. 2020-04-29 16:38:18 +10:00
stijn 84fa3312cf all: Format code to add space after C++-style comment start.
Note: the uncrustify configuration is explicitly set to 'add' instead of
'force' in order not to alter the comments which use extra spaces after //
as a means of indenting text for clarity.
2020-04-23 11:24:25 +10:00
Andrew Leech 8ee2e1fdbc stm32/mboot: Expose custom DFU USB VID/PID values at makefile level.
In mboot, the ability to override the USB vendor/product id's was added
back in 5688c9ba09.  However, when the main
firmware is turned into a DFU file the default VID/PID are used there.
pydfu.py doesn't care about this but dfu-util does and prevents its use
when the VID/PID don't match.

This commit exposes BOOTLOADER_DFU_USB_VID/PID as make variables, for use
on either command line or mpconfigboard.mk, to set VID/PID in both mboot
and DFU files.
2020-04-18 23:02:00 +10:00
stijn 30840ebc99 all: Enable extra conversion warnings where applicable.
Add -Wdouble-promotion and -Wfloat-conversion for most ports to ban out
implicit floating point conversions, and add extra Travis builds using
MICROPY_FLOAT_IMPL_FLOAT to uncover warnings which weren't found
previously.  For the unix port -Wsign-comparison is added as well but only
there since only clang supports this but gcc doesn't.
2020-04-18 22:42:28 +10:00
stijn 70affd9ba2 all: Fix implicit floating point to integer conversions.
These are found when building with -Wfloat-conversion.
2020-04-18 22:42:24 +10:00
stijn bcf01d1686 all: Fix implicit conversion from double to float.
These are found when building with -Wfloat-conversion.
2020-04-18 22:42:24 +10:00
Martin Fischer 28833690bb stm32/mboot/README: Clarify that mboot can access FAT formatted FS only. 2020-04-16 16:28:07 +10:00
Martin Fischer 7942d0b688 stm32/storage: Fix start address of second, internal block device. 2020-04-16 16:25:20 +10:00
Damien George 8e048d2548 all: Clean up error strings to use lowercase and change cannot to can't.
Now that error string compression is supported it's more important to have
consistent error string formatting (eg all lowercase English words,
consistent contractions).  This commit cleans up some of the strings to
make them more consistent.
2020-04-13 22:19:37 +10:00
Jim Mussared 073b9a5eb8 ports: Enable error text compression for various ports, but not all.
Enabled on: bare-arm, minimal, unix coverage/dev/minimal, stm32, esp32,
esp8266, cc3200, teensy, qemu-arm, nrf.  Not enabled on others to be able
to test the code when the feature is disabled (the default case).

Code size change for this commit:

   bare-arm:  -600 -0.906%
minimal x86:  -308 -0.208%
   unix x64:    +0 +0.000%
unix nanbox:    +0 +0.000%
      stm32: -3368 -0.869% PYBV10
     cc3200: -1024 -0.558%
    esp8266: -2512 -0.368% GENERIC
      esp32: -2876 -0.205% GENERIC[incl -3168(data)]
        nrf: -1708 -1.173% pca10040
       samd:    +0 +0.000% ADAFRUIT_ITSYBITSY_M4_EXPRESS
2020-04-05 15:02:06 +10:00
Jim Mussared def76fe4d9 all: Use MP_ERROR_TEXT for all error messages. 2020-04-05 15:02:06 +10:00
Jim Mussared 994c1dd57a stm32/Makefile: Add missing ordering dependency on generated headers. 2020-04-05 14:12:59 +10:00
Damien George 1a3e386c67 all: Remove spaces inside and around parenthesis.
Using new options enabled in the uncrustify configuration.
2020-03-28 23:36:44 +11:00
Damien George 83461e37d4 stm32/boards: Disable pend_throw, uheapq, utimeq on small-flash boards.
These are mainly used by the previous version of uasyncio which is now
replaced by a newer version, with built-in C module _uasyncio.  Saves about
1300 bytes of flash.
2020-03-28 13:55:59 +11:00
Damien George 09154f585f stm32/mpconfigport.h: Make most extended modules configurable by board. 2020-03-28 13:46:35 +11:00
Damien George dbba6b05dc stm32/mpconfigport.h: Remove unused root pointer for BTstack bindings.
This was a cut-and-paste error from the NimBLE bindings.
2020-03-27 00:30:37 +11:00
Damien George 35e2dd0979 stm32: Enable and freeze uasyncio. 2020-03-26 01:25:45 +11:00
Damien George f05ae416ff stm32/softtimer: Initialise pairing-heap node before pushing to heap. 2020-03-26 01:21:04 +11:00
Zoltán Vörös c5cc64175b ports: Add lib/libm/roundf.c to bare-metal Makefile's.
This function is not used by the core but having it as part of the build
allows it to be used by user C modules, or board extensions.  The linker
won't include it in the final firmware if it remains unused.
2020-03-25 01:22:00 +11:00
Damien George feb2577585 all: Remove spaces between nested paren and inside function arg paren.
Using new options enabled in the uncrustify configuration.
2020-03-25 00:39:46 +11:00
Damien George 40255aff23 stm32/mboot: Remove unnecessary test for led being 1 in led_state.
The "led" argument is always a pointer to the GPIO port, or'd with the pin
that the LED is on, so testing that it is "1" is unnecessary.  The type of
"led" is also changed to uint32_t so it can properly hold a 32-bit pointer.
2020-03-25 00:10:32 +11:00
Andrew Leech 9dd470b768 stm32/mboot: Update LED0 state from systick handler.
Updating the LED0 state from systick handler ensures LED0 is always
consistent with its flash rate regardless of other processing going on in
either interrupts or main.  This improves the visible stability of the
bootloader, rather than LED0 flashing somewhat randomly at times.

This commit also changes the LED0 flash rate depending on the current state
of DFU, giving slightly more visual feedback on what the device is doing.
2020-03-25 00:08:32 +11:00
Andrew Leech f7130a99b6 stm32/mboot: Protect against invalid address flash writes.
And provide a DFU error message for invalid erases and writes.
2020-03-22 15:23:49 +11:00
Andrew Leech b41d08cf15 stm32/mboot: Update dfu state/status flags to better match standard. 2020-03-22 14:11:16 +11:00
Andrew Leech 03b1ed80e7 stm32/mboot: Allow overriding led_init and led_state in board folder.
Allows for custom functions/logic to display mboot state.
2020-03-22 13:48:45 +11:00
Damien George eae495a714 stm32/main: Fix bug mounting 3rd SD partition.
Fixes issue #5753.
2020-03-12 12:34:31 +11:00
Damien George ed848553b4 extmod/vfs: Factor out vfs mount-and-chdir helper from stm32. 2020-03-11 14:24:26 +11:00
Damien George e965363b6b stm32: Refactor Bluetooth HCI RX to be independent of transport layer.
Now all HCI specific code (eg UART vs WB55 internal messaging) is confined
to modbluetooth_hci.c.
2020-03-10 01:53:42 +11:00
Damien George 0674917bc5 extmod/btstack: Implement advertising.
Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-10 01:53:42 +11:00
Damien George 51f8591097 stm32/boards/PYBD: Allow building with BTstack (via make command line).
Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-10 01:53:42 +11:00
Damien George 0e95815bfb stm32: Add bindings for BTstack implementation.
Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-10 01:53:42 +11:00
Damien George 894c550c86 stm32: Refactor bluetooth stack/hci/driver bindings.
This makes a cleaner separation between the: driver, HCI UART and BT stack.
Also updated the naming to be more consistent (mp_bluetooth_hci_*).

Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-10 01:53:42 +11:00
Damien George c44d52f33e extmod/modbluetooth_nimble: Move nimble specific code, factor nimble.mk.
Move extmod/modbluetooth_nimble.* to extmod/nimble.  And move common
Makefile lines to extmod/nimble/nimble.mk (which was previously only used
by stm32).  This allows (upcoming) btstack to follow a similar structure.

Work done in collaboration with Jim Mussared aka @jimmo.
2020-03-06 12:35:20 +11:00
Damien George 44aa5b2200 stm32/modnetwork: Remove redundant call to nimble_poll in lwip poll.
The bluetooth stack has its own dedicated polling function, see
mod_bluetooth_nimble_poll_wrapper().
2020-03-06 12:35:20 +11:00
Damien George 69661f3343 all: Reformat C and Python source code with tools/codeformat.py.
This is run with uncrustify 0.70.1, and black 19.10b0.
2020-02-28 10:33:03 +11:00
Damien George 3f39d18c2b all: Add *FORMAT-OFF* in various places.
This string is recognised by uncrustify, to disable formatting in the
region marked by these comments.  This is necessary in the qstrdef*.h files
to prevent modification of the strings within the Q(...).  In other places
it is used to prevent excessive reformatting that would make the code less
readable.
2020-02-28 10:31:07 +11:00
hahmadi b169904254 stm32/mpconfigport.h: Add option to have custom help text.
Define MICROPY_PY_BUILTINS_HELP_TEXT in <yourboard>/mpconfigboard.h for a
custom help text.
2020-02-21 15:02:19 +11:00
Andrew Leech 3fe83e4318 stm32/sdram: Fix compile issue from unused sdram startup test flag. 2020-02-18 14:22:03 +11:00
Damien George ad7213d3c3 py: Add mp_raise_msg_varg helper and use it where appropriate.
This commit adds mp_raise_msg_varg(type, fmt, ...) as a helper for
nlr_raise(mp_obj_new_exception_msg_varg(type, fmt, ...)).  It makes the
C-level API for raising exceptions more consistent, and reduces code size
on most ports:

   bare-arm:   +28 +0.042%
minimal x86:  +100 +0.067%
   unix x64:   -56 -0.011%
unix nanbox:  -300 -0.068%
      stm32:  -204 -0.054% PYBV10
     cc3200:    +0 +0.000%
    esp8266:   -64 -0.010% GENERIC
      esp32:  -104 -0.007% GENERIC
        nrf:  -136 -0.094% pca10040
       samd:    +0 +0.000% ADAFRUIT_ITSYBITSY_M4_EXPRESS
2020-02-13 11:52:40 +11:00
Damien George 97eca38c4f py: Add mp_raise_type helper macro and use it where appropriate.
This provides a more consistent C-level API to raise exceptions, ie moving
away from nlr_raise towards mp_raise_XXX.  It also reduces code size by a
small amount on some ports.
2020-02-13 11:03:37 +11:00
Damien George ce40abcf21 stm32/usbd_cdc_interface: Remove "interrupt_char != -1" check.
It's not needed.  The C integer implicit promotion rules mean that the
uint8_t of the incoming character is promoted to a (signed) int, matching
the type of interrupt_char.  Thus the uint8_t incoming character can never
be equal to -1 (the value of interrupt_char that indicate that interruption
is disabled).
2020-02-07 16:08:37 +11:00
Damien George 98a3911c43 py/scheduler: Add "raise_exc" argument to mp_handle_pending.
Previous behaviour is when this argument is set to "true", in which case
the function will raise any pending exception.  Setting it to "false" will
cancel any pending exception.
2020-02-07 16:08:20 +11:00
Damien George d6a1e45caa stm32/usbd_conf: Allow boards to configure USB HS ULPI NXT/DIR pins. 2020-02-04 23:15:55 +11:00
Andrew Leech ff9a61b5a8 stm32/sdram: Expose the result of sdram startup test in stm32_main.
This means boards can choose to only use it for gc heap if the test passes.
2020-02-04 18:18:41 +11:00
Damien George af88e70414 stm32/powerctrl: Reenable PLL3 on H7 MCUs when waking from stop mode.
So that USB can work.
2020-01-31 23:25:18 +11:00
Damien George 2c8c2b935e stm32/powerctrl: Improve support for changing system freq on H7 MCUs.
This commit improves pllvalues.py to generate PLL values for H7 MCUs that
are valid (VCO in and out are in range) and extend for the entire range of
SYSCLK values up to 400MHz (up to 480MHz is currently unsupported).
2020-01-31 23:25:18 +11:00
Damien George 03b73ce329 stm32/stm32_it: Don't call __HAL_USB_HS_EXTI_CLEAR_FLAG on H7 MCUs.
It doesn't exist on these MCUs.
2020-01-31 23:25:18 +11:00
Damien George 257b17ec10 stm32/sdio: Add support for H7 MCUs.
The cyw43 driver on stm32 will now work with H7 MCUs.
2020-01-31 23:25:18 +11:00
Damien George 31ba06ce84 stm32/boards/stm32f746_af.csv: Add ADC alt functions to correct pins. 2020-01-30 16:31:11 +11:00
Damien George 68db7e01d8 stm32/powerctrl: Enable overdrive on F7 when waking from stop mode.
Because if the SYSCLK is set to 180MHz or higher it will require this to be
on already.
2020-01-30 16:30:03 +11:00
Damien George 29b84ea798 stm32/powerctrl: Disable HSI if not needed to save a bit of power. 2020-01-30 16:29:45 +11:00
Damien George 96a4435be1 stm32/boards/STM32F769DISC: Add config to use external SPI as filesys.
This board now has the following 3 build configurations:
- mboot + external QSPI in XIP mode + internal filesystem
- mboot + external QSPI with filesystem (the default)
- no mboot + external QSPI with filesystem
2020-01-30 14:40:38 +11:00
Damien George 7bb2bf965e stm32/Makefile: Allow a board's .mk file to add things to CFLAGS. 2020-01-30 14:39:46 +11:00
Andrew Leech 30501d3f54 drivers, stm32: Support SPI/QSPI flash chips over 16MB.
With a SPI flash that has more than 16MB, 32-bit addressing is required
rather than the standard 24-bit.  This commit adds support for 32-bit
addressing so that the SPI flash commands (read/write/erase) are selected
automatically depending on the size of the address being used at each
operation.
2020-01-30 13:18:38 +11:00
David Lechner b72cb0ca1b py/mpthread.h: Use strong type for mp_thread_set_state() argument.
This modifies the signature of mp_thread_set_state() to use
mp_state_thread_t* instead of void*.  This matches the return type of
mp_thread_get_state(), which returns the same value.

`struct _mp_state_thread_t;` had to be moved before
`#include <mpthreadport.h>` since the stm32 port uses it in its
mpthreadport.h file.
2020-01-29 17:10:32 +11:00
Damien George a542c6d7e0 stm32/powerctrl: For F7, allow PLLM!=HSE when setting PLLSAI to 48MHz.
PLLM is shared among all PLL blocks on F7 MCUs, and this calculation to
configure PLLSAI to have 48MHz on the P output previously assumed that PLLM
is equal to HSE (eg PLLM=25 for HSE=25MHz).  This commit relaxes this
assumption to allow other values of PLLM.
2020-01-29 16:49:13 +11:00
Damien George f70373c7b2 stm32/softtimer: Change linear linked list to a pairing heap. 2020-01-22 17:31:18 +11:00
Memiks 4ab4bf3ec6 ports: Modify mp_hal_pin_write macro so it can be used as a function.
Even though it doesn't return anything it could still be used like a
function.  Addresses issue #5501.
2020-01-14 23:48:42 +11:00
Damien George bfbd94401d py: Make mp_obj_get_type() return a const ptr to mp_obj_type_t.
Most types are in rodata/ROM, and mp_obj_base_t.type is a constant pointer,
so enforce this const-ness throughout the code base.  If a type ever needs
to be modified (eg a user type) then a simple cast can be used.
2020-01-09 11:25:26 +11:00
Damien George e3187b052f stm32/boards/PYBD: Change RTC asynch prediv from 1 to 4.
This change has the following effects:
- Reduces the resolution of the RTC sub-second counter from 30.52us to
  122.07us.
- Allows RTC.calibration() to now support positive values (as well as
  negative values).
- Reduces VBAT current consumption in standby mode by a small amount.

For general purpose use 122us resolution of the sub-second counter is
good enough, and the benefits of full range calibration and minor reduction
in VBAT consumption are worth the change.
2020-01-07 23:59:29 +11:00
Nicko van Someren 4c93955b7b py/objslice: Add support for indices() method on slice objects.
Instances of the slice class are passed to __getitem__() on objects when
the user indexes them with a slice.  In practice the majority of the time
(other than passing it on untouched) is to work out what the slice means in
the context of an array dimension of a particular length.  Since Python 2.3
there has been a method on the slice class, indices(), that takes a
dimension length and returns the real start, stop and step, accounting for
missing or negative values in the slice spec.  This commit implements such
a indices() method on the slice class.

It is configurable at compile-time via MICROPY_PY_BUILTINS_SLICE_INDICES,
disabled by default, enabled on unix, stm32 and esp32 ports.

This commit also adds new tests for slice indices and for slicing unicode
strings.
2019-12-28 23:55:15 +11:00
Yonatan Goldschmidt 61d2b40ad5 lib/utils/pyexec: Introduce MICROPY_REPL_INFO, wrap debug prints in it.
For the 3 ports that already make use of this feature (stm32, nrf and
teensy) this doesn't make any difference, it just allows to disable it from
now on.

For other ports that use pyexec, this decreases code size because the debug
printing code is dead (it can't be enabled) but the compiler can't deduce
that, so code is still emitted.
2019-12-28 00:05:39 +11:00
David Lechner e79424d672 ports: Allow overriding CROSS_COMPILE in a custom makefile.
Many ports already allow overriding CROSS_COMPILE.  This modifies the
remaining ports to allow it as well.
2019-12-27 23:53:16 +11:00
Damien George 93509ac8c7 stm32: Add configuration to build in nanbox mode.
Most stm32 boards can now be built in nan-boxing mode via:

    $ make NANBOX=1

Note that if float is enabled then it will be forced to double-precision.
Also, native emitters will be disabled.
2019-12-27 22:54:53 +11:00
Damien George d980d51807 stm32: Fix to build in nanbox mode. 2019-12-27 22:54:53 +11:00
Damien George 09376f0e47 py: Introduce MP_ROM_NONE macro for ROM to refer to None object.
This helps to prevent mistakes, and allows easily changing the ROM value of
None if needed.
2019-12-27 22:51:17 +11:00
Jim Mussared 90f286465b stm32/mbedtls: Resize mbedtls output buffer from 16 down to 4 kiB.
To reduce the size of the SSL context on the heap.  See issue #5303.
2019-12-21 00:02:24 +11:00
Damien George 7ac326c424 stm32/boards/PYBD: Include webrepl helper scripts in frozen manifest. 2019-12-20 13:20:20 +11:00
iabdalkader 3078a4b2e2 stm32/timer: Add missing TIM 1/15/16/17 IRQ handlers for H7 MCUs. 2019-12-19 17:19:53 +11:00
roland van straten 43b576d88d stm32/boards/NUCLEO_H743ZI: Add extra pins and peripheral definitions.
- Corrected pin assignments and checked with CubeMX.
- Added additional I2C and UARTs.
- Added Ethernet interface definitions with lwIP and SSL support (but
  Ethernet is currently unsupported on H7 MCUs so not fully enabled).
2019-12-19 16:54:33 +11:00
roland van straten 26a78edb49 stm32/boards/NUCLEO_F767ZI: Update pins, peripherals and total flash.
- Removed remarks on DFU/OCD in mpconfigboard.h because deploy-stlink works
  fine too.
- Added more UARTs, I2C, corrected SPI, CAN, etc; verified against CubeMX.
- Adapted pins.csv to remove errors, add omissions, etc. according to
  NUCLEO-144 User Manual.
- Changed linker file stm32f767.ld to reflect correct size of the Flash.
- Tested with LAN and SD card.
2019-12-19 11:43:19 +11:00
roland van straten 8af139e8a4 stm32/boards/NUCLEO_F767ZI: Add pins and config for using an SD card.
The Nucleo board does not have an SD card slot but does have the requisite
pins next to each other and labelled, so provide the configuration for
convenience.
2019-12-19 11:28:47 +11:00
Damien George fb01415599 stm32/boards/PYBD_SF2: Configure LEDs as inverted, for LED.intensity(). 2019-12-13 17:28:24 +11:00
Damien George 71c6bfd08a stm32/modusocket: Handle case of NULL NIC in socket ioctl. 2019-12-13 14:45:21 +11:00
Damien George c2eaf56634 stm32/Makefile: Enable max buffer size on W5200 NIC when used with lwIP.
Because in network_wiznet5k the TX/RX buffers are set to 16k each when in
MACRAW mode, which is used with lwIP.
2019-12-13 12:36:12 +11:00
Jim Mussared b76f0a73bc stm32/main: Fix SKIPSD file detection so SD card is mounted by default.
The condition for skipping was accidentally inverted in
7723dac337

Fixes issue #5400.
2019-12-09 17:01:30 +11:00
Damiano Mazzella cc634b9e92 stm32/boards/xxx_WB55: Enable littlefs2 on WB55 boards. 2019-12-09 14:07:29 +11:00
Chris Mason d61e7a6d8a stm32/uart: Add support for UART4/5 on L0 MCUs. 2019-12-05 15:31:41 +11:00
Damien George 40cc7ec677 stm32/mpconfigport.h: Use IRQ_PRI_PENDSV to protect bluetooth ringbuf.
The default protection for the BLE ringbuf is to use
MICROPY_BEGIN_ATOMIC_SECTION, which disables all interrupts. On stm32 it
only needs to disable the lowest priority IRQ, pendsv, because that's the
IRQ level at which the BLE stack is driven.
2019-12-04 13:39:22 +11:00
Damien George ba5e4841ec stm32/main: Fix auto creation of pyb.Flash on boot with kw-only args. 2019-11-27 22:47:05 +11:00
Damien George 11c22430d4 stm32/boards/NUCLEO_L073RZ: Skip board-pin names for CPU only pins.
This board doesn't have much flash and removing these unneeded names saves
about 900 bytes of code size.
2019-11-27 21:59:47 +11:00
Damien George 77b8f86a5e stm32/qstrdefsport.h: Remove unused qstrs and make USB ones conditional.
qstrs in this file are always included in all builds, even if not used
anywhere.  So remove those that are never needed, and make USB names
conditional on having USB enabled.
2019-11-27 21:59:47 +11:00
Damien George 797c2e8fc2 stm32/storage: Make start/len args of pyb.Flash keyword only.
To allow the future possibility of initial positional args, like flash id.
2019-11-26 21:35:00 +11:00
Damien George d8057c325a stm32/storage: Change storage_read/write_blocks to return int type.
And return -MP_EIO if calling storage_read_block/storage_write_block fails.
This lines up with the return type and value (negative for error) of the
calls to MICROPY_HW_BDEV_READBLOCKS (and WRITEBLOCKS, and BDEV2 versions).
2019-11-26 00:08:57 +11:00
Damien George 120368ba1a stm32/boards: Enable LFS2 on PYBv1.x and PYBD boards. 2019-11-26 00:08:57 +11:00
Damien George 715e4fc25f stm32/moduos: Add VfsLfs1 and VfsLfs2 to uos module, if enabled. 2019-11-26 00:07:09 +11:00
Damien George 7897f5d9be stm32/main: Auto detect block device used for main filesystem. 2019-11-26 00:07:09 +11:00
Damien George c169094f61 stm32/storage: Make pyb.Flash configurable, and support ext block proto.
The pyb.Flash() class can now be used to construct objects which reference
sections of the flash storage, starting at a certain offset and going for a
certain length.  Such objects also support the extended block protocol.
The signature for the constructor is: pyb.Flash(start=-1, len=-1).
2019-11-26 00:07:09 +11:00
Damien George 7723dac337 stm32: Generalise flash mounting code so it supports arbitrary FS.
This commit refactors and generalises the boot-mount routine on stm32 so
that it can mount filesystems of arbitrary type.  That is, it no longer
assumes that the filesystem is FAT.  It does this by using mp_vfs_mount()
which does auto-detection of the filesystem type.
2019-11-25 18:10:58 +11:00
Jim Mussared fbb7646e3b stm32/nimble_hci_uart.c: Prevent scheduler running during CYW-BT wakeup.
Using mp_hal_delay_ms allows the scheduler to run, which might result in
another transmit operation happening, which would bypass the sleep (and
fail).  Use mp_hal_delay_us instead.
2019-11-25 17:32:10 +11:00
Mike Causer 258b147830 stm32/boards/stm32f405_af.csv: Fix typo in ETH_RMII_REF_CLK on PA1. 2019-11-11 12:02:14 +11:00
Damien George 799b6d1e0c extmod: Consolidate FAT FS config to MICROPY_VFS_FAT across all ports.
This commit removes the Makefile-level MICROPY_FATFS config and moves the
MICROPY_VFS_FAT config to the Makefile level to replace it.  It also moves
the include of the oofatfs source files in the build from each port to a
central place in extmod/extmod.mk.

For a port to enabled VFS FAT support it should now set MICROPY_VFS_FAT=1
at the level of the Makefile.  This will include the relevant oofatfs files
in the build and set MICROPY_VFS_FAT=1 at the C (preprocessor) level.
2019-11-11 11:37:38 +11:00
Damien George cddb2dd0c3 stm32/mpthreadport: Include runtime.h to get defn of mp_raise_msg. 2019-11-05 13:20:25 +11:00
Damien George c13f9f209d all: Convert nlr_raise(mp_obj_new_exception_msg(x)) to mp_raise_msg(x).
This helper function was added a while ago and these are the remaining
cases to convert, to save a bit of code size.
2019-11-05 11:35:45 +11:00
Damien George 32eae53fbc stm32/boards: Enable support for bluetooth on WB55 boards. 2019-11-01 14:58:24 +11:00
Damien George 6a64b280d0 stm32: Add support for RF coprocessor on WB55 MCUs.
This requires a BLE wireless stack firmware to be already programmed in the
secure flash area of the device.
2019-11-01 14:52:17 +11:00
Damien George 40ea1915fc extmod/nimble: Factor out stm32-specific HCI UART RX/TX code. 2019-11-01 12:41:37 +11:00
Damien George 48b25a841b stm32: Add machine.Timer with soft timer implementation.
This commit adds an implementation of machine.Timer backed by the soft
timer mechanism.  It allows an arbitrary number of timers with 1ms
resolution, with an associated Python callback.  The Python-level API
matches existing ports that have a soft timer, and is used as:

    from machine import Timer
    t = Timer(freq=10, callback=lambda t:print(t))
    ...
    t = Timer(mode=Timer.ONE_SHOT, period=2000, callback=lambda t:print(t))
    ...
    t.deinit()
2019-10-31 22:12:55 +11:00
Damien George a5d97f1db9 stm32: Add soft timer implementation, using SysTick at 1ms resolution.
This commit adds an implementation of a "software timer" with a 1ms
resolution, using SysTick.  It allows unlimited number of concurrent
timers (limited only by memory needed for each timer entry).  They can be
one-shot or periodic, and associated with a Python callback.

There is a very small overhead added to the SysTick IRQ, which could be
further optimised in the future, eg by patching SysTick_Handler code
dynamically.
2019-10-31 22:12:55 +11:00
Damien George 9ec73aedb4 stm32/timer: Fix Timer.freq() calc so mult doesn't overflow uint32_t.
Fixes issue #5280.
2019-10-31 12:49:18 +11:00
Damien George cfe1c5abf8 extmod/vfs: Rename BP_IOCTL_xxx constants to MP_BLOCKDEV_IOCTL_xxx.
Also rename SEC_COUNT to BLOCK_COUNT and SEC_SIZE to BLOCK_SIZE.
2019-10-29 14:17:29 +11:00
Damien George 9aabb6c01b extmod: Factor out block-device struct to make independent of fatfs. 2019-10-29 12:12:37 +11:00
Jim Mussared ece4e21a55 stm32/Makefile: Only enable hardware sqrt on parts that support it.
Not enough to detect f7/h7, need to use the specific parts.

Follow-up to 580a2656d1.
2019-10-28 15:08:28 +11:00
Andrew Leech 19ca025b45 stm32/sdram: Fix to use new mpu_config_start/mpu_config_end signature. 2019-10-22 22:02:06 +11:00
Jim Mussared b02d7e612d extmod/modbluetooth: Rename module to "ubluetooth".
For consistency with "umachine". Now that weak links are enabled
by default for built-in modules, this should be a no-op, but allows
extension of the bluetooth module by user code.

Also move registration of ubluetooth to objmodule rather than
port-specific.
2019-10-22 21:58:05 +11:00
Damien George d2384efa80 py: Automatically provide weak links from "foo" to "ufoo" module name.
This commit implements automatic module weak links for all built-in
modules, by searching for "ufoo" in the built-in module list if "foo"
cannot be found.  This means that all modules named "ufoo" are always
available as "foo".  Also, a port can no longer add any other weak links,
which makes strict the definition of a weak link.

It saves some code size (about 100-200 bytes) on ports that previously had
lots of weak links.

Some changes from the previous behaviour:
- It doesn't intern the non-u module names (eg "foo" is not interned),
  which saves code size, but will mean that "import foo" creates a new qstr
  (namely "foo") in RAM (unless the importing module is frozen).
- help('modules') no longer lists non-u module names, only the u-variants;
  this reduces duplication in the help listing.

Weak links are effectively the same as having a set of symbolic links on
the filesystem that is searched last.  So an "import foo" will search
built-in modules first, then all paths in sys.path, then weak links last,
importing "ufoo" if it exists.  Thus a file called "foo.py" somewhere in
sys.path will still have precedence over the weak link of "foo" to "ufoo".

See issues: #1740, #4449, #5229, #5241.
2019-10-22 15:30:52 +11:00
Jim Mussared 8ba963cfa3 tools/makemanifest.py: Eval relative paths w.r.t. current manifest file.
When loading a manifest file, e.g. by include(), it will chdir first to the
directory of that manifest.  This means that all file operations within a
manifest are relative to that manifest's location.

As a consequence of this, additional environment variables are needed to
find absolute paths, so the following are added: $(MPY_LIB_DIR),
$(PORT_DIR), $(BOARD_DIR).  And rename $(MPY) to $(MPY_DIR) to be
consistent.

Existing manifests are updated to match.
2019-10-21 23:01:41 +11:00
Damien George 12413e92a3 stm32/powerctrlboot: Fix config of systick IRQ priority on F0/L0/WB MCU.
Prior to this commit the systick IRQ priority was set at lowest priority on
F0/L0/WB MCUs, because it was left at the default and never configured.
This commit ensures the priority is configured and sets it to the highest
priority.
2019-10-21 12:23:41 +11:00
Damien George 69b238ec63 stm32/accel: Fix Accel.read() method so it does read a byte.
This bug was introduced in a0f7b4c678
2019-10-18 11:53:34 +11:00
Frederic.Pierson 925f244ab3 stm32/boards: Add NADHAT_PYB405 board. 2019-10-18 11:41:22 +11:00
Frederic.Pierson 28062b5108 stm32/accel: Add support for KXTJ3. 2019-10-18 11:41:22 +11:00
Damien George 3105207aff stm32/accel: Rename MMA I2C macro constants to make it generic. 2019-10-18 11:35:32 +11:00
Damien George 4f2c737b0c stm32/mpu: Save and restore the IRQ state when configuring MPU.
In case IRQs are already disabled during the MPU configuration.

Fixes issue #5152.
2019-10-16 23:12:06 +11:00
iabdalkader 6e4468a2ab stm32/adc: Fix sampling for internal channels on H7 MCUs.
Set to 810 cycles following HAL examples.
2019-10-15 22:08:45 +11:00
iabdalkader 4cee42d864 stm32/adc: Use IS_CHANNEL_INTERNAL macro to check for internal channels. 2019-10-15 22:08:36 +11:00
iabdalkader d523a377d1 stm32/adc: Remove unused macro and channel check, and fix spacing.
The call to is_adcx_channel is redundant because the channel is already
checked just before calling adc_init_single in adc_make_new.
2019-10-15 22:04:19 +11:00
iabdalkader cb2b210d45 stm32/adc: Update ADC driver to work with the new H7 HAL.
Use NB_TO_CHANNEL to map decimal numbers to channel numbers.  And use the
correct rank to initialize channels (ADC_REGULAR_RANK_1).
2019-10-15 22:03:54 +11:00
Damien George 287800d6e1 stm32: Convert to use FROZEN_MANIFEST to specify frozen code.
All symlinks are removed, frozen files are now referenced via
boards/manifest.py.
2019-10-15 21:36:24 +11:00
Damien George d7a9388fe0 ports: Add new make target "submodules" which inits required modules. 2019-10-15 17:14:41 +11:00
ladyada 06ae818f93 stm32/boards: Add new board ADAFRUIT_F405_EXPRESS. 2019-10-11 11:50:36 +11:00
Jim Mussared 580a2656d1 stm32: Use hardware double sqrt on F7/H7 MCUs.
Identical to cd527bb324 but for doubles.
This gives a -2.754% improvement on bm_float.py, and -35% improvement on
calling sqrt in a loop.
2019-10-10 17:39:32 +11:00
Andrey Belykh 305f537bf9 stm32/sdcard: Support boards with no SD card detect pin.
If MICROPY_HW_SDCARD_DETECT_PIN is not defined then the SD card will always
be detected as present.
2019-10-10 17:29:44 +11:00
Andrew Leech 04fe62d06f stm32/mboot: Add option to automatically reset when USB is disconnected.
Enable in board config with: #define MBOOT_USB_RESET_ON_DISCONNECT (1)
2019-10-08 16:07:32 +11:00
Jim Mussared 902bb4ceae stm32: Extract port-specific Nimble implementation.
On other ports (e.g. ESP32) they provide a complete Nimble implementation
(i.e. we don't need to use the code in extmod/nimble). This change
extracts out the bits that we don't need to use in other ports:
 - malloc/free/realloc for Nimble memory.
 - pendsv poll handler
 - depowering the cywbt

Also cleans up the root pointer management.
2019-10-08 14:40:35 +11:00
Damien George 4a6974bea5 stm32/boards/PYBD_SF2: Put nimble library in external QSPI XIP flash.
The BLE stack is not performance critical, so put it in external
memory-mapped flash to save internal flash for other things (like frozen
bytecode).
2019-10-05 23:51:33 +10:00
Martin Fischer a0ce01f62e stm32/usbdev: Fix compile error if MICROPY_HW_USB_CDC_NUM is set to 2.
Fixes regression introduced by 6705767da1
2019-10-05 23:33:38 +10:00
Chris Mason 0096041c99 stm32/{adc,machine_adc}: Change ADC clock and sampling time for F0 MCUs.
STM32F0 has PCLK=48MHz and maximum ADC clock is 14MHz so use PCLK/4=12MHz
to stay within spec of the ADC peripheral.  In pyb.ADC set common sampling
time to approx 4uS for internal and external sources.  In machine.ADC
reduce sample time to approx 1uS for external source, leave internal at
maximum sampling time.
2019-10-04 21:39:17 +10:00
Damien George 26e90a0514 stm32/boards: Enable MICROPY_HW_RTC_USE_LSE on L4 boards.
The previous commit changed the default configuration on L4 MCUs to use
LSI, so configure these boards to use LSE again.
2019-10-04 16:10:13 +10:00
hahmadi 266146ad64 stm32/system_stm32: Support selection of HSE and LSI on L4 MCUs.
This commit adds the option to use HSE or MSI system clock, and LSE or LSI
RTC clock, on L4 MCUs.

Note that prior to this commit the default clocks on an L4 part were MSI
and LSE.  The defaults are now MSI and LSI.

In mpconfigboard.h select the clock source via:

    #define MICROPY_HW_RTC_USE_LSE (0) or (1)
    #define MICROPY_HW_CLK_USE_HSE (0) or (1)

and the PLLSAI1 N,P,Q,R settings:

    #define MICROPY_HW_CLK_PLLSAIN (12)
    #define MICROPY_HW_CLK_PLLSAIP (RCC_PLLP_DIV7)
    #define MICROPY_HW_CLK_PLLSAIQ (RCC_PLLQ_DIV2)
    #define MICROPY_HW_CLK_PLLSAIR (RCC_PLLR_DIV2)
2019-10-04 16:09:06 +10:00
Jim Mussared fafa9d35dd stm32/boards/PYBD: Enable BLE for Pyboard D. 2019-10-01 09:51:02 +10:00
Jim Mussared 6f35f214d3 stm32/mpconfigport.h: Add modbluetooth module to stm32. 2019-10-01 09:51:02 +10:00
Jim Mussared d72dbb822c stm32: Provide port-specific implementation for Nimble on STM32. 2019-10-01 09:51:02 +10:00
Andrew Leech 4ba0aff472 stm32/uart: Add RTS/CTS pin configuration support to UART4. 2019-09-27 13:24:01 +10:00
Chris Mason eb12fa3862 stm32/powerctrlboot: Add support for HSI at 8MHz on F0 MCUs.
For use with F0 MCUs that don't have HSI48.  Select the clock source
explicitly in mpconfigboard.h.

On the NUCLEO_F091RC board use HSE bypass when HSE is chosen because the
NUCLEO clock source is STLINK not a crystal.
2019-09-26 17:34:04 +10:00
Chris Mason f16e4be3fa stm32/powerctrlboot: Fix clock and PLL selection for HSI48 on F0 MCUs.
Before this patch the UART baudrate on F0 MCUs was wrong because the
stm32lib SystemCoreClockUpdate sets SystemCoreClock to 8MHz instead of
48MHz if HSI48 is routed directly to SYSCLK.

The workaround is to use HSI48 -> PREDIV (/2) -> PLL (*2) -> SYSCLK.

Fixes issue #5049.
2019-09-26 17:32:22 +10:00
Damien George 3328b7d71f stm32: Support disabling the compiler.
Disable via "#define MICROPY_ENABLE_COMPILER (0)" in the board's
mpconfigboard.h file.
2019-09-26 17:05:40 +10:00
Josh Lloyd 7d58a197cf py: Rename MP_QSTR_NULL to MP_QSTRnull to avoid intern collisions.
Fixes #5140.
2019-09-26 16:04:56 +10:00
Andrew Leech 2397b44062 stm32/usbd_cdc_interface: Add CTS flow control option for USB VCP.
Enabled by default, but disabled when REPL is connected to the VCP (this is
the existing behaviour).  Can be configured at run-time with, eg:

    pyb.USB_VCP().init(flow=pyb.USB_VCP.RTS | pyb.USB_VCP.CTS)
2019-09-26 13:50:24 +10:00
Damien George 6b4666f8cf stm32/can: Guard header file by MICROPY_HW_ENABLE_CAN.
Because not all MCU series have a CAN peripheral.
2019-09-23 23:45:07 +10:00
Damien George ca8ff99e8c stm32: Use mp_printf with MICROPY_ERROR_PRINTER for uncaught exceptions. 2019-09-23 17:15:07 +10:00
iabdalkader 4f78ba3cf4 stm32/boards/NUCLEO_H743ZI: Enable FDCAN on this board. 2019-09-23 17:00:54 +10:00
iabdalkader f7a07b3605 stm32: Add support for FDCAN peripheral, exposed as pyb.CAN.
The new fdcan.c file provides the low-level C interface to the FDCAN
peripheral, and pyb_can.c is updated to support both traditional CAN and
FDCAN, depending on the MCU being compiled for.
2019-09-23 17:00:54 +10:00
Damien George d06fd384c2 stm32/can: Factor CAN driver into low-level and Python bindings.
can.c now contains the low-level C interface to the CAN peripheral, and
pyb_can.c the Python-level class/methods/constants.
2019-09-23 16:58:08 +10:00
Chris Liechti 6f7e774d12 stm32/machine_i2c: Add ability to specify I2C(4) by name. 2019-09-23 15:08:24 +10:00
iabdalkader 73c94bbbd4 stm32/modusocket: Fix NULL deref when accept() an unbound socket. 2019-09-17 12:30:10 +10:00
Damien George 22099ab88f stm32/machine_adc: Fix build for F4 and L4 MCUs that only have ADC1. 2019-09-12 19:10:12 +10:00
Damien George f66616556d stm32/lwip_inc: Enable LWIP_NETIF_EXT_STATUS_CALLBACK for mDNS.
This feature makes sure that mDNS is automatically restarted when there is
any change event on a netif.
2019-09-12 18:08:50 +10:00
Damien George b0e17bbb9d stm32/lwip_inc: Allocate additional MEMP_SYS_TIMEOUT when mDNS enabled.
Since v2.1 of lwIP mDNS uses a MEMP_SYS_TIMEOUT slot, so allocate an extra
one when this feature is enabled.
2019-09-12 18:05:27 +10:00
Damien George bcaafa3823 stm32/usb: Verify number of used endpoints doesn't exceed maximum. 2019-09-11 15:17:38 +10:00
Damien George 6705767da1 stm32/usb: Add support for VCP+MSC+HID mode, incl 2xVCP and 3xVCP. 2019-09-11 15:17:38 +10:00
cristian cfec054073 stm32/board/NUCLEO_F746ZG: Enable Ethernet periph, lwip and ussl. 2019-09-11 11:20:58 +10:00
Jim Mussared c8c37ca407 stm32/boards/STM32F769DISC: Fix number of SDRAM row bits.
According to the schematic, the SDRAM part on this board is a
MT48LC4M32B2B5-6A, with "Row addressing 4K A[11:0]" (per datasheet).  This
commit updates mpconfigboard.h from 13 to 12 to match.
2019-09-10 23:13:52 +10:00
Christopher Wilson f9d142523c stm32/boards/MIKROE_CLICKER2_STM32: Add MikroElektronika Clicker2 board.
- STM32F407VGT6 (1MB of Flash, 192+4 Kbytes of SRAM)
- 5V (via USB) or Li-Polymer Battery (3.7V) power input
- 2 x LEDs
- 2 x user switches
- 2 x mikroBUS sockets
- 2 x 1x26 mikromedia-compatible headers (52 pins)

https://www.mikroe.com/clicker-2-stm32f4
2019-09-10 13:57:01 +10:00
Damien George 2b07f56c2b stm32/boards/NUCLEO_L073RZ: Fix typo in MCU name. 2019-09-10 11:53:00 +10:00
Chris Wilson a605b53702 stm32/mboot: Support boards with only two LEDs.
Mboot currently requires at least three LEDs to display each of the four
states.  However, since there are only four possible states, the states can
be displayed via binary counting on only 2 LEDs (if only 2 are available).
The existing patterns are still used for 3 or 4 LEDs.
2019-09-10 11:25:56 +10:00
Damien George bd2e46e0a5 stm32/boards/stm32wb55_af.csv: Fix ADC pin-channel function mapping. 2019-09-06 17:56:34 +10:00
Damien George 62fe013a5f stm32/machine_adc: Improve operation of ADC for H7, L4 and WB MCUs. 2019-09-06 17:55:12 +10:00
Damien George ebacdfabb6 stm32/machine_adc: Add machine.ADC class. 2019-09-04 15:40:24 +10:00
Jim Mussared 06661890de stm32/powerctrl: Fix machine.bootloader() for L0 MCUs. 2019-09-04 11:36:53 +10:00
Jim Mussared 8fc00928ea stm32/dma: Fix DMA config for L0 MCUs. 2019-09-03 23:33:09 +10:00
Jim Mussared 74fe841449 docs/library/pyb.DAC.rst: Correct frequency for triangle mode output.
Also correct comments in related code.
2019-09-03 23:25:45 +10:00
Damien George 400a128e11 stm32/stm32_it: Include correct EXTI interrupt handlers for L0 MCUs. 2019-08-29 12:00:18 +10:00
iabdalkader 0bec07f32b stm32/extint: Fix EXTI mapping of PVD and RTC events for H7 MCUs. 2019-08-28 12:53:42 +10:00
Damien George 5789558d60 stm32/boards/PYBD_SF2: Exclude certain things when building mboot. 2019-08-28 12:37:13 +10:00
Damien George 68d74b0074 stm32/mboot/Makefile: Define "BUILDING_MBOOT" when building mboot.
So boards can configure their settings based on whether mboot or the main
firmware is being built.
2019-08-28 12:37:13 +10:00
Damien George b1e04848ef stm32/mphalport: Put PYBD specific MAC code in board specific file. 2019-08-28 12:37:13 +10:00
stijn af5c998f37 py/modmath: Implement math.isclose() for non-complex numbers.
As per PEP 485, this function appeared in for Python 3.5.  Configured via
MICROPY_PY_MATH_ISCLOSE which is disabled by default, but enabled for the
ports which already have MICROPY_PY_MATH_SPECIAL_FUNCTIONS enabled.
2019-08-17 23:23:17 +10:00
Damien George 3eff81288c stm32/i2c: Fix generation of restart condition for hw I2C on F0/F7.
Before this patch I2C transactions using a hardware I2C peripheral on F0/F7
MCUs would not correctly generate the I2C restart condition, and instead
would generate a stop followed by a start.  This is because the CR2 AUTOEND
bit was being set before CR2 START when the peripheral already had the I2C
bus from a previous transaction that did not generate a stop.

As a consequence all combined transactions, eg read-then-write for an I2C
memory transfer, generated a stop condition after the first transaction and
didn't generate a stop at the very end (but still released the bus).  Some
I2C devices require a repeated start to function correctly.

This patch fixes this by making sure the CR2 AUTOEND bit is set after the
start condition and slave address have been fully transferred out.
2019-08-16 13:34:04 +10:00
Damien George 497683b315 gitignore: Put build-*/ pattern in top-level gitignore file. 2019-08-16 00:08:08 +10:00
Damien George 25d3509986 stm32/usbd: Make USB device FIFO sizes dynamically configurable.
Allows to optimise and configure the FIFO sizes depending on the USB device
configuration selected at runtime, eg VCP+MSC vs 3xVCP+MSC.
2019-08-15 13:56:50 +10:00
Damien George 8485b72d0d stm32/boards/NUCLEO_L432KC: Add config for USB VCP support. 2019-08-15 12:46:34 +10:00
Damien George 97e8e036c5 stm32/usbd: Support USB device mode on STM32L432 MCUs. 2019-08-15 12:46:04 +10:00
Damien George bf733c27bb stm32/usbd: Introduce MICROPY_HW_USB_IS_MULTI_OTG to simplify USB config
This is an internal config value that is enabled for MCUs that have
multiple OTG instances, to simplify #if configuration of the USB code.
2019-08-15 12:19:28 +10:00
Damien George ba607809f2 stm32/modpyb: Support building with PY_PYB_LEGACY on and HW_USB_HID off. 2019-08-15 12:03:32 +10:00
Chris Wilson 3d02ebb4e8 stm32/sdcard: Support configuring the SD/MMC bus width to 1 or 4 bits.
Some SD/MMC breakout boards don't support 4-bit bus mode.  This adds a new
macro MICROPY_HW_SDMMC_BUS_WIDTH that allows each board to define the width
of the SD/MMC bus interface used on that board, defaulting to 4 bits.
2019-08-08 12:53:05 +10:00
Damien George 102815f700 stm32/mpconfigport.h: Enable lwIP raw sockets. 2019-08-06 15:56:05 +10:00
Damien George 0e2b224b07 stm32/lwip_inc: Enable raw socket type. 2019-08-06 15:56:05 +10:00
Damien George 473157eeb9 stm32/usbd_hid_interface: Include extra header to build with threading. 2019-07-26 12:44:14 +10:00
Damien George ad0b7cb017 stm32/boards/xxx_WB55: Enable USB HID now that it works on WB MCUs. 2019-07-25 17:49:53 +10:00
Damien George fa07deda9f stm32/usbd_hid_interface: Rewrite USB HID interface code.
The previous version did not work on MCUs that only had USB device mode
(compared to OTG) because of the handling of NAK.  And this previous
handling of NAK had a race condition where a new packet could come in
before USBD_HID_SetNAK was called (since USBD_HID_ReceivePacket clears NAK
as part of its operation).  Furthermore, the double buffering of incoming
reports was not working, only one buffer could be used at a time.

This commit rewrites the HID interface code to have a single incoming
buffer, and only calls USBD_HID_ReceivePacket after the user has read the
incoming report (similar to how the VCP does its flow control).  As such,
USBD_HID_SetNAK and USBD_HID_ClearNAK are no longer needed.

API functionality from the user's point of view should be unchanged with
this commit.
2019-07-25 17:42:17 +10:00
Damien George b1129df478 stm32/dma: Fix re-start of DMA stream by clearing all event flags.
As per the datasheet, all event flags for a stream must be cleared before
enabling it.  Fixes issue #4944 (with DAC.write_timed).
2019-07-25 16:48:26 +10:00
badlyby 3b258ef213 stm32/boards/NUCLEO_F722ZE: Add definition files for new board. 2019-07-25 16:31:36 +10:00
badlyby 09267bb147 stm32/boards/stm32f722.ld: Provide memory regions for internal FS. 2019-07-25 16:31:36 +10:00
badlyby 0da2f6f23a stm32/flashbdev: Support internal filesystem on STM32F722/23/32/33. 2019-07-25 16:31:12 +10:00
Damien George 0c12adca46 stm32/boards/USBDONGLE_WB55: Add definition files for new board. 2019-07-17 17:00:34 +10:00
Damien George d2a8fb747f stm32/boards/NUCLEO_WB55: Add definition files for new board. 2019-07-17 17:00:34 +10:00
Damien George 9849567a06 stm32/boards: Add MCU support files for STM32WB55. 2019-07-17 16:50:42 +10:00
Damien George 59b7166d87 stm32: Add initial support for STM32WBxx MCUs.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor.  The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it.  Supported
features so far include: RTC, UART, USB, internal flash filesystem.
2019-07-17 16:33:31 +10:00
Damien George d42392b9a7 stm32/make-stmconst.py: Allow more variation in parens and int-suffix L. 2019-07-17 16:27:17 +10:00
Damien George 02b2ad4fbd stm32/boards/STM32F769DISC: Fix length of FLASH_APP section.
Fixes issue #4924.
2019-07-17 16:19:50 +10:00
Damien George baea43bba7 stm32/boards/B_L072Z_LRWAN1: Enable USB VCP support. 2019-07-16 14:50:44 +10:00
Damien George 64aebca155 stm32/Makefile: Allow a board to disable float support.
By using "MICROPY_FLOAT_IMPL = none" in its mpconfigboard.mk file.
2019-07-16 14:47:32 +10:00
Damien George 102d9911e9 stm32/mphalport: Fix GPIO clock enable for L0 MCUs. 2019-07-16 14:47:12 +10:00
Damien George 4096fa397b stm32/powerctrlboot: Increase SYSCLK to 32MHz for L0 MCUs. 2019-07-16 14:46:31 +10:00
Damien George 4c1ad1f691 stm32: Add support for USB on L0 MCUs. 2019-07-16 14:45:53 +10:00
Damien George 788e7f50f2 stm32/usbd_cdc_interface: Make CDC TX/RX buffer sizes configurable. 2019-07-16 14:41:59 +10:00
Damien George f302f784e9 stm32/usb: Add config options to disable USB MSC and/or HID.
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID.  They are both
enabled by default.
2019-07-16 14:39:21 +10:00
Damien George fd49fcb229 stm32/gccollect: Always use MP_STATE_THREAD(stack_top) to get stack top.
In a non-thread build, using &_ram_end as the top-of-stack is no longer
correct because the stack is not always at the very top end of RAM.  See
eg 04c7cdb668 and
3786592097.  The correct value to use is
&_estack, which is the value stored in MP_STATE_THREAD(stack_top), and
using the same code for both thread and non-thread builds makes the code
cleaner.
2019-07-11 17:32:01 +10:00
Damien George a17b901a9e stm32/boards/B_L072Z_LRWAN1: Add definition files for new board. 2019-07-09 12:54:09 +10:00
Damien George 278e9bffe9 stm32/mboot: Update dependencies to enable parallel build with -j. 2019-07-09 11:46:47 +10:00
Damien George 342539bdcc stm32/mboot: Use STARTUP_FILE from stm32lib. 2019-07-09 11:35:47 +10:00
Damien George 5a81d2d6b8 stm32/mboot: Remove use of BSRRL/H for H7 MCUs due to stm32lib update. 2019-07-09 11:34:54 +10:00
Damien George c8f19f1371 stm32/mboot: Make _estack an array to avoid compiler warnings.
The compiler can warn about out-of-bounds array access if _estack is just a
single uint8_t.
2019-07-09 11:33:57 +10:00
Damien George d43dd886a5 stm32/boards/NUCLEO_F413ZH: Remove STARTUP_FILE, it's defined globally.
The Makefile now defines this variable to the correct value (but it can
still be overridden by a board if necessary).
2019-07-09 11:32:12 +10:00
Chris Mason c24d81119c stm32/boards/NUCLEO_L452RE: Add definition files for new board. 2019-07-08 16:50:45 +10:00
Chris Mason 64181b5f76 stm32: Add support for STM32L452 MCUs. 2019-07-08 16:50:19 +10:00
Damien George eea61a09c4 stm32/boards/NUCLEO_F446RE: Enable DAC. 2019-07-08 16:08:40 +10:00