Also found a race condition between timer_disable and redraw, which
would happen if I debugger-paused inside common_hal_rgbmatrix_timer_disable
or put a delay or print inside it. That's what pausing inside reconstruct
fixes.
So that the "right timer" can be chosen, `timer_allocate` now gets the `self`
pointer. It's guaranteed at this point that the pin information is accurate,
so you can e.g., find a PWM unit related to the pins themselves.
This required touching each port to add the parameter even though it's
unused everywhere but raspberrypi.
This is a slight trade-off with code size, in places where a "_varg"
mp_raise variant is now used. The net savings on trinket_m0 is
just 32 bytes.
It also means that the translation will include the original English
text, and cannot be translated. These are usually names of Python
types such as int, set, or dict or special values such as "inf" or
"Nan".
The motivation for doing this is so that we can allow
common_hal_mcu_disable_interrupts in IRQ context, something that works
on other ports, but not on nRF with SD enabled. This is because
when SD is enabled, calling sd_softdevice_is_enabled in the context
of an interrupt with priority 2 or 3 causes a HardFault. We have chosen
to give the USB interrupt priority 2 on nRF, the highest priority that
is compatible with SD.
Since at least SoftDevice s130 v2.0.1, sd_nvic_critical_region_enter/exit
have been implemented as inline functions and are safe to call even if
softdevice is not enabled. Reference kindly provided by danh:
https://devzone.nordicsemi.com/f/nordic-q-a/29553/sd_nvic_critical_region_enter-exit-missing-in-s130-v2
Switching to these as the default/only way to enable/disable interrupts
simplifies things, and fixes several problems and potential problems:
* Interrupts at priority 2 or 3 could not call common_hal_mcu_disable_interrupts
because the call to sd_softdevice_is_enabled would HardFault
* Hypothetically, the state of sd_softdevice_is_enabled
could change from the disable to the enable call, meaning the calls
would not match (__disable_irq() could be balanced with
sd_nvic_critical_region_exit).
This also fixes a problem I believe would exist if disable() were called
twice when SD is enabled. There is a single "is_nested_critical_region"
flag, and the second call would set it to 1. Both of the enable()
calls that followed would call critical_region_exit(1), and interrupts
would not properly be reenabled. In the new version of the code,
we use our own nesting_count value to track the intended state, so
now nested disable()s only call critical_region_enter() once, only
updating is_nested_critical_region once; and only the second enable()
call will call critical_region_exit, with the right value of i_n_c_r.
Finally, in port_sleep_until_interrupt, if !sd_enabled, we really do
need to __disable_irq, rather than using the common_hal_mcu routines;
the reason why is documented in a comment.
This pulls all common functionality into `shared-bindings` and keeps
platform-specific code inside `nrf`. Additionally, this performs most
validation in the `shared-bindings` site.
The only validation that occurs inside platform-specific `common-hal`
code is related to timeout limits that are platform-specific.
Additionally, all documentation is now inside the `shared-bindings`
directory.
Signed-off-by: Sean Cross <sean@xobs.io>
For `microcontroller.reset()`, don't manually call NVIC_SystemReset().
Instead, call the `port_reset()` in case the port wants to do any
cleanup.
Signed-off-by: Sean Cross <sean@xobs.io>
This finishes the rework of the exception handler, which is once
again stored inside the watchdog timer module.
This also implements a `watchdog_reset()` that is used to disable the
RAISE watchdog, if one is enabled.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds an exception to be raised when the WatchDogTimer times out.
Note that this currently causes a HardFault, and it's not clear why it's
not behaving properly.
Signed-off-by: Sean Cross <sean@xobs.io>
The timeout value is calculated by the common-hal layer now, so we don't
need to be quite so clever about calculating it here.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a field to allow specifying a timeout when initiating advertising.
As part of this, add a new property to determine if the device is still
advertising.
Additionally, have the `anonymous` property require a timeout, and set
the timeout to the maximum possible value if no timeout is specified.
Signed-off-by: Sean Cross <sean@xobs.io>
Add a new parameter to the `start_advertising()` function to enable
anonymous advertising. This forces a call to `sd_ble_gap_privacy_set()`
with `privacy_mode` set to `BLE_GAP_PRIVACY_MODE_DEVICE_PRIVACY` and
`private_addr_type` set to
`BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE`.
With this, addresses will cycle at a predefined rate (currently once
every 15 minutes).
Signed-off-by: Sean Cross <sean@xobs.io>
Store the RTC value in the .uninitialized section, but make sure to
flank it with some known values. That way we can determine if the RTC
value has been initialized, or if it's random uninitialized garbage.
As part of this, add a `common_hal_rtc_init()` routine to determine if
the value is correct, or reset it to 0 if it is not valid.
Signed-off-by: Sean Cross <sean@xobs.io>
Allow for setting various softradio memory settings as part of a
board in order to support lower-memory configurations. If a
parameter is unspecified then the previously-defined value is used.
Signed-off-by: Sean Cross <sean@xobs.io>
This adds preliminary support for the nRF52833, which is a variant of
the nRF52840 with half the RAM, half the flash, and fewer peripherals.
Signed-off-by: Sean Cross <sean@xobs.io>
This gets all the purely internal references. Some uses of
protomatter/Protomatter/PROTOMATTER remain, as they are references
to symbols in the Protomatter C library itself.
I originally believed that there would be a wrapper library around it,
like with _pixelbuf; but this proves not to be the case, as there's
too little for the library to do.
PacketBuffer facilitates packet oriented BLE protocols such as BLE
MIDI and the Apple Media Service.
This also adds PHY, MTU and connection event extension negotiation
to speed up data transfer when possible.
disable only turns off ENABLE but doesn't set the init tracking that
nrfx uses. uninit hangs if ENABLE is off and is called because it
waits forever for TX to stop.
The "spacing" of "buffer structure" is confusing, use the "channel count"
instead.
Testing performed on nrf52840 feather:
Play stereo and mono, 8- and 16-bit, 8kHz RawSamples representing 333.33Hz
square waves.
Use both mono and stereo PWMAudioOut instances.
Scope the RC-filtered signal and use the scope's frequency
measurement function, verify the frequency is 333 or 334Hz in all tested
cases.
In the "stereo output" cases, verify both the L and R channels. Verify
the output amplitude is the same in both channels.
In the "stereo output" cases, run a second test where the L channel's
amplitude is attenuated 50%. Verify the output amplitude is correct
in each channel.
