Also fix MAX_ENDPOINT definition for G0, which follows G4.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
By specifying rts=pin(x) and/or cts=Pin(x) in the constructor. The pad
numbers for the UART pins are fix in this case: TX must be at pad 0, RX at
pad 1, RTS at pad 2 and CTS at pad 3.
repr(uart) shows the pin names for rts and cts, if set. In case of a RX
overflow, the rx interrupt will be disabled instead of just discarding the
data. That allows RTS to act.
If RTS is inactive, still 2 bytes can be buffered in the FIFO.
Signed-off-by: robert-hh <robert@hammelrath.com>
With Crystal: set the crystal startup wait time to 1 second. It was 2
seconds before, and that seeemed too long.
With USB-Sync: scan for up to 1 second for the USB to be registered and
carry on with boot as soon as it it. Before, the code just waited for
500ms.
Side change: improve related comments.
Signed-off-by: robert-hh <robert@hammelrath.com>
These include ADC, DAC, I2C, SoftI2C, SPI, SoftI2C, PWM, UART, pulse. This
is useful for devices like the Adafruit Trinket series which have almost no
accessible GPIO pins.
Signed-off-by: robert-hh <robert@hammelrath.com>
If sockets were open when calling soft reset, gc_sweep_all() would try to
close them. In case of e.g. the NINA WiFi handler, connected through SPI,
spi_transfer() would be called for command exchange with the NINA module.
But at that time SerCom was already disabled.
Moving sercom_deinit_all() behind gc_sweep_all() solves this issue.
Signed-off-by: robert-hh <robert@hammelrath.com>
Such that they are easier to adapt. The maximum code size is set by:
MICROPY_HW_CODESIZE=xxxK
in mpconfigmcu.mk for the MCU family as default or in mpconfigboard.mk for
a specific board. Setting the maximum code size allows the loader to error
out if the code gets larger than the space dedicated for it.
Signed-off-by: robert-hh <robert@hammelrath.com>
Change UART clock source on S3/C3 so the UART can operate when CPU
frequency is below 80MHz. This allows the UART to remain operational when
using Dynamic Frequency Scaling (DFS).
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
This commit enables the ULP for the S2 and S3 chips.
Note this is the FSM (Finite State Machine) ULP.
Signed-off-by: Patrick Joy <patrick@joytech.com.au>
Once all the firmware has been flashed and the final signatures checked,
mboot writes the "all good" byte into the header of the application. This
step uses the buffer firmware_head which, if unaligned in the build, fails
when cast to a uint64_t* in flash.c.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
These were incorrectly added in d995c01042.
The fix here includes the full differential ADC definitions.
Signed-off-by: brave ulysses <brave_ulysses@email.com>
When the network module was first introduced in the esp8266 port in
ee3fec3167 there was only one interface (STA)
and, to save flash, the WLAN object was aliased to the network module,
which had just static methods for WLAN operations. This was subsequently
changed in 9e8396accb when the AP interface
was introduced, and the WLAN object became a true class.
But, network.WLAN remained a function that returned either the STA or AP
object and was never upgraded to the type itself. This scheme was then
copied over to the esp32 port when it was first introduced.
This commit changes network.WLAN from a function to a reference to the WLAN
type. This makes it consistent with other ports and network objects, and
allows accessing constants of network.WLAN without creating an instance.
Signed-off-by: Damien George <damien@micropython.org>
Building the Pico-W needs the MICROPY_PY_NETWORK_CYW43 flag to be set in
order to include building the CYW43 Wifi driver. But then mp_hal_get_mac()
handles the MAC assignment for all nics the "CYW43 way", copying the real
MAC provided by the WiFi hardware. This will fail for all other NIC types,
resulting in an invalid MAC address.
The solution in this commit is to add a check for the NIC type parameter
idx and handle the MAC address respectively.
Convert to an absolute path to always reliably locate manifest.py. This is
already done in Makefile, but is also needed in CMakeLists.txt if cmake is
invoked directly.
Signed-off-by: Phil Howard <phil@pimoroni.com>
Currently rp2.StateMachine.exec(instr_in) requires that the instr_in
parameter be a string representing the PIO assembly language instruction
to be encoded by rp2.asm_pio_encode(). This commit allows the parameter
to also be of integral type. This is useful if the exec() method is
being called often where the use of pre-encoded machine code is
desireable.
This commit still supports calls like:
sm.exec("set(0, 1)")
It also now supports calls like:
# Performed once earlier, maybe in __init__()
assembled_instr = rp2.asm_pio_encode("out(y, 8)", 0)
# Performed multiple times later as the PIO state machine is
# configured for its next run.
sm.exec(assembled_instr)
The existing examples/rp2/pio_exec.py and examples/rp2/pio_pwm.py that
exercise the rp2.StateMachine.exec() method still work with this change.
Signed-off-by: Adam Green <adamgrym@yahoo.com>
FSP v4.4.0 refers to CMSIS V5.4.1, and __COMPILER_BARRIER() is used in bsp.
On the other hand, lib/cmsis is V5.1.0 and the macro is not defined.
Therefore, compile error happens.
As the workaround, the macro definition is added.
If lib/cmsis is updated in the future, this addition can be removed.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
This modifies the windows port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).
Signed-off-by: David Lechner <david@pybricks.com>
This modifies the unix port Makefile to use += for QSTR_DEFS and
QSTR_GLOBAL_DEPENDENCIES so that variants can add additional files if
needed (similar to stm32 port).
Signed-off-by: David Lechner <david@pybricks.com>
It was treated as an error before. The error surfaced when using the
NINAW10 drivers for WiFi support. Even if this is a bad behavior of the
NINA driver, machine_spi can be forgiving in that situation.
Separate low level flash access from mimxrt flash driver object. Allows
better abstraction from hardware for testing and reuse in other areas (e.g.
bootloader).
Signed-off-by: Philipp Ebensberger <philipp.ebensberger@3bricks-software.de>
For esp32 and esp8266 this commit adds:
- a 'pm' option to WLAN.config() to set/get the wifi power saving mode; and
- PM_NONE, PM_PERFORMANCE and PM_POWERSAVE constants to the WLAN class.
This API should be general enough to use with all WLAN drivers.
Documentation is also added.
All ports that enable MICROPY_PY_MACHINE_PWM now enable these two
sub-options, so remove these sub-options altogether to force consistency in
new ports that implement machine.PWM.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Limit duty_u16() to 65535 and duty_ns() to the period duration.
- Return 0 for pwm.freq() if the frequency has not been set yet.
- Return 0 for pwm.duty_us16() and duty_ns() unless both frequency and
duty cycle have been set.
- Initialize the pin to PWM at the very end of the constructor, to avoid
possible glitches on the pin when setting up the PWM.
This adds support for freq/duty_u16/duty_ns keyword arguments in the PWM
constructor, and adds the PWM.init() method. Using init() without
arguments enables a previously deinit-ed PWM again.
Further changes in this commit:
- Do not start PWM output if only duty was set.
- Stop all PWM slices on soft-reset.
- Fix a bug when changing the freq on a channel pair with duty_ns set.
The PWM.init() method has been added. Calling init() without arguments
restarts a PWM channel stopped with deinit(). Otherwise single parameters
except for "device=n" can be changed again. The device can only be
specified once, either in the constructor or the first init() call.
Also simplify get_pwm_config() and get_adc_config(), and shrink the PWM
object.
And also fix/improve the following:
- Simplify the duty handling a little bit.
- Allow duty_u16(65536), which sets the output high.
- Rename machine_pwm_start() to mp_machine_pwm_start(), in preparation for
a possible start/stop method pair.
This fixes:
- type-comparison (E721): do not compare types, use isinstance().
- string-dot-format-missing-arguments (F524): .format call is missing
argument(s) for placeholder(s): {message}.
- f-string-missing-placeholders (F541).
- is-literal (F632): Use != to compare constant literals.
The last one is fixed by just comparing for truthfulness of `state`.
ESP-NOW is a proprietary wireless communication protocol which supports
connectionless communication between ESP32 and ESP8266 devices, using
vendor specific WiFi frames. This commit adds support for this protocol
through a new `espnow` module.
This commit builds on original work done by @nickzoic, @shawwwn and with
contributions from @zoland. Features include:
- Use of (extended) ring buffers in py/ringbuf.[ch] for robust IO.
- Signal strength (RSSI) monitoring.
- Core support in `_espnow` C module, extended by `espnow.py` module.
- Asyncio support via `aioespnow.py` module (separate to this commit).
- Docs provided at `docs/library/espnow.rst`.
Methods available in espnow.ESPNow class are:
- active(True/False)
- config(): set rx buffer size, read timeout and tx rate
- recv()/irecv()/recvinto() to read incoming messages from peers
- send() to send messages to peer devices
- any() to test if a message is ready to read
- irq() to set callback for received messages
- stats() returns transfer stats:
(tx_pkts, tx_pkt_responses, tx_failures, rx_pkts, lost_rx_pkts)
- add_peer(mac, ...) registers a peer before sending messages
- get_peer(mac) returns peer info: (mac, lmk, channel, ifidx, encrypt)
- mod_peer(mac, ...) changes peer info parameters
- get_peers() returns all peer info tuples
- peers_table supports RSSI signal monitoring for received messages:
{peer1: [rssi, time_ms], peer2: [rssi, time_ms], ...}
ESP8266 is a pared down version of the ESP32 ESPNow support due to code
size restrictions and differences in the low-level API. See docs for
details.
Also included is a test suite in tests/multi_espnow. This tests basic
espnow data transfer, multiple transfers, various message sizes, encrypted
messages (pmk and lmk), and asyncio support.
Initial work is from https://github.com/micropython/micropython/pull/4115.
Initial import of code is from:
https://github.com/nickzoic/micropython/tree/espnow-4115.
This allows updating mp_mbedtls_errors.c for the other mbedtls based ports
based on mbedTLS v2.28.1. This esp32-specific file will not be required
after updating IDF support to >= v4.4.1.
Signed-off-by: Carlos Gil <carlosgilglez@gmail.com>
API change: time.time_ns() is added, but it just returns 0.
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
API additions;
- time.sleep() is added
- time.ticks_cpu() is added, but it just returns 0
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
API change: time.time_ns() is added, but it just returns 0.
No API or functional change to existing time functions.
Signed-off-by: Damien George <damien@micropython.org>
Based on extmod/utime_mphal.c, with:
- a globals dict added
- time.localtime wrapper added
- time.time wrapper added
- time.time_ns function added
New configuration options are added for this module:
- MICROPY_PY_UTIME (enabled at basic features level)
- MICROPY_PY_UTIME_GMTIME_LOCALTIME_MKTIME
- MICROPY_PY_UTIME_TIME_TIME_NS
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Change MICROPY_HW_BOARD_NAME definition to match the product name.
- Rename board folder's name to match the product name style.
- Change related files like Makefile, document descriptions, test cases, CI
and tools.
Signed-off-by: Takeo Takahashi <takeo.takahashi.xv@renesas.com>
Since c80e7c14e6 changed the GC heap to use
all unused RAM, there is no longer any RAM available for the traditional C
heap (which is not used by default in MicroPython but may be used by C
extensions). This commit adds a provision for a board to reserve RAM for
the C heap, by defining MICROPY_C_HEAP_SIZE.
Signed-off-by: Damien George <damien@micropython.org>
The previous code worked on ESP32 but not ESP32-S3. All the IDF (v4.4.3)
examples call rmt_set_tx_loop_mode before rmt_write_items, so make that
change here.
Signed-off-by: Damien George <damien@micropython.org>
- Use HCI_TRACE macro consistently.
- Use the same colour formatting.
- Add a tool to convert to .pcap for Wireshark.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This adds a mechanism to track a pending notify/indicate operation that
is deferred due to the send buffer being full. This uses a tracked alloc
that is passed as the content arg to the callback.
This replaces the previous mechanism that did this via the global pending
op queue, shared with client read/write ops.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Makes gatts_notify and gatts_indicate work in the same way: by default they
send the DB value, but you can manually override the payload.
In other words, makes gatts_indicate work the same as gatts_notify.
Note: This removes support for queuing notifications and indications on
btstack when the ACL buffer is full. This functionality will be
reimplemented in a future commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds support for the `timeout` keyword argument to machine.I2C
on the rp2 port, following how it's done on other ports.
The main motivation here is avoid the interpreter crashing due to infinite
loops when SDA is stuck low, which is quite common if the board gets reset
while reading from an I2C device.
A default timeout of 50ms is chosen because it's consistent with:
- Commit a707fe50b0 which used a timeout of
50,000us for zero-length writes on the rp2 port.
- The machine.SoftI2C class which uses 50,000us as the default timeout.
- The stm32 port's hardware I2C, which uses 50,000us for
I2C_POLL_DEFAULT_TIMEOUT_US.
This commit also fixes the default timeout on the esp32 port to be
consistent with the above, and updates the documentation for machine.I2C to
document this keyword argument.
If a board defines a custom bootloader entry function it will be called
first, if not and the ROM API supports RUN bootloader API, then
`machine.bootloader()` will jump to the ROM serial downloader in USB mode.
This commit allows boards to disable Ethernet and keep the networking stack
enabled, to use an alternate networking interface, such as WiFi.
Note that the `network` and `socket` modules are now enabled by default for
a board.
This commit is necessary to make MicroPython work on this eval kit out of
the box, as the eval kit ships with the HyperFlash physically disconnected
from the bus (refer to the schematics or the user guide) and the QSPI
connected instead, but the fuses/board/pins are configured to boot from
internal flash (on FlexSPI2).
Note that enabling the HyperFlash is not trivial, as it requires soldering
and desoldering of many small footprint resistors and changing fuses.
Helps prevent the filesystem from getting formatted by mistake, among other
things. For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).
Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state. If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application. The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it. But defining
"long enough" is impossible for all the different boards and their possible
behaviour. The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C. That code then effectively
acts like normal C start-up code, which also cannot be interrupted.
Note: on the stm32 port this was never seen as an issue because all
start-up code is in C. But now other ports start to put more things in
_boot.py and so this problem crops up.
Signed-off-by: David Grayson <davidegrayson@gmail.com>
The dispatch active flag is only set once and never reset, so it will
always call the dispatch handler (once enabled), and it's not really
needed because it doesn't make things more efficient.
Also remove unused included headers.
Changes in this commit:
- Move the pwm_seq array to the p_config data structure. That prevents
potential resource collisions between PWM devices.
- Rename the keyword argument 'id' to 'device'. That's consistent with the
SAMD port as the other port allowing to specify it.
This is a best-effort implementation of write polling. It's difficult to
do correctly because if there are multiple output streams (eg UART and USB
CDC) then some may not be writeable while others are. A full solution
should also have a return value from mp_hal_stdout_tx_strn(), returning the
number of bytes written to the stream(s). That's also hard to define.
The renesas-ra and stm32 ports already implement a similar best-effort
mechanism for write polling.
Fixes issue #11026.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, setting of UART parameters like parity, stop bits or
data bits did not work correctly. As suggested by @iabdalkader, adding
__DSB() fixes the problem, making sure that changes to the UART LCR_H
register are seen by the peripheral.
Note: the FIFO is already enabled in the call to uart_init(), so the call
to uart_set_fifo_enabled() is not required, but kept for visibility.
Fixes issue #10976.
The following have been tested and are working:
- 550MHz CPU frequency
- UART REPL via ST-Link
- USB REPL and mass storage
- 3x LEDs and 1x user button
- Ethernet
Signed-off-by: Damien George <damien@micropython.org>
For builds with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1, calling
stdio_init_all() in main() detaches the UART input from REPL. This change
suppresses calling stdio_init_all() then.
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Add the timeout and timeout_char keyword options.
- Make uart.read() non-blocking.
- Add uart.any().
- Add ioctl MP_STREAM_POLL handling.
- Change uart.write() into non-busy waiting. uart.write() still waits until
all data has been sent, but calls MICROPY_EVENT_POLL_HOOK while waiting.
uart.write() uses DMA for transfer. One option would be to add a small
local buffer, such that transfers up to the size of the buffer could be
done without waiting.
- As a side effect to the change of uart.write(), uart.txdone() and ioctl
flush now report/wait correctly for the end of transmission.
- Change machine_hard_uart_buf_t in machine_hard_uart_obj_t to an instance
of that struct, rather than a pointer to one.
Even if boards do not have a clock crystal. In that case, the clock
quality will be very poor.
Always having machine.RTC means that the date/time can be set in a way that
is consistent with other ports.
This commit also removes the special code in modutime.c for devices without
the RTC class.
Signed-off-by: Damien George <damien@micropython.org>
These have the same frequency, but can have different duty cycle and
polarity.
pwm.deinit() stops all channels of a module, but does not release the
module. pwm.init() without arguments restarts all outputs.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.
Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
cycles.
- Limited to the P0.x pins.
Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
Borrowing an idea from the mimxrt port (also stm32 port): in the loader
input file memmap_mp.ld calculate __GcHeapStart and __GcHeapEnd as the
unused RAM. Then in main.c use these addresses as arguments to gc_init().
The benefits of this change are:
1) When libraries are added or removed in the future changing BSS usage,
main.c's sizing of the GC heap does not need to be changed.
2) Currently these changes make the GC area about 30 KBytes larger, eg on
PICO_W the GC heap increases from 166016 to 192448 bytes. Without that
change this RAM would never get used.
3) If someone wants to disable one or more SRAM blocks on the RP2040 to
reduce power consumption it will be easy: just change the MEMORY section
in memmap_mp.ld. For instance to not use SRAM2 and SRAM3 change it to:
MEMORY
{
FLASH(rx) : ORIGIN = 0x10000000, LENGTH = 2048k
RAM(rwx) : ORIGIN = 0x21000000, LENGTH = 128k
SCRATCH_X(rwx) : ORIGIN = 0x20040000, LENGTH = 4k
SCRATCH_Y(rwx) : ORIGIN = 0x20041000, LENGTH = 4k
}
Then to turn off clocks for SRAM2 and SRAM3 from MicroPython, set the
appropriate bits in WAKE_EN0 and SLEEP_EN0.
Tested by running the firmware.uf2 file on PICO_W and displaying
micropython.mem_info(). Confirmed GC total size approximately matched the
size calculated by the loader.
Signed-off-by: cpottle9 <cpottle9@outlook.com>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
These changes allow the firmware to support both the REV-1 and REV-2
versions of the board:
- Freeze the new device drivers used in REV-2.
- Add a board-level module that abstracts the IMU chipset.
Changes are:
- Freeze micropython-lib time module to get strftime.
- Reserve the last 1MB of QSPI flash for (optional) WiFi firmware storage.
- Disable SD card mount on boot.
- Enable high-speed BLE firmware download.
This is for boards without networking support so that the default boot.py
continues to work.
Also update boot.py to use network.country and network.hostname instead.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Rather than duplicating the implementation of `network`, this allows
ESP8266 to use the shared one in extmod. In particular this gains access
to network.hostname and network.country.
Other than adding these two methods, there is no other user-visible change.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
