Testing performed: That a card is successfully mounted on Pygamer with
the built in SD card slot
This module is enabled for most FULL_BUILD boards, but is disabled for
samd21 ("M0"), litex, and pca10100 for various reasons.
Ujson should only worry about whitespace before JSON. This becomes apparent when you are using MP stream protocol to read directly from input buffers.
When you attempt to read(1) on a UART (and possibly other protocols) you have to wait for either the byte or the timeout.
Fixes:
- Waiting for a timeout after you have completed reading a correct and complete JSON off the input.
- Raising an OSError after reading a correct and complete JSON off the input.
- Eating more data than semantically owned off the input buffer.
- Blocking to start parsing JSON until the entire JSON body has been loaded into a potentially large, contiguous Python object.
Code you would write before:
```
line = board_busio_uart_port.read_line()
json_dict = json.loads(line)
```
or reaching for fixed buffers and swapping them around in Python.
Code that did not work before that does now:
```
json_dict = json.load(board_busio_uart_port)
```
- This removes the need for intermediate copies of data when reading JSON from micropython stream protocol inputs.
- It also increases total application speed by parsing JSON concurrently with receiving on boards that read from UART via DMA.
- It simplifies code that users write while improving their apps.
Surely readline() "rtype" is string not int as stated (and not bytes as some might expect).
Also it is not totally unambiguous what happens on a timeout so it would help to clarify in docs that on a timeout
it does NOT return with what it has read so far, rather it leaves all that in the buffer ready for a future read and returns nothing.
Likewise clarify that if timeout=0 but there is no newline it DOES return what it has read so far (NOT None).
At least this is what I think it does and/or is supposed to do!
Python docs are generally not too explicit about what is the proper treatment, so perhaps all the more reason to
clarify the interpretation adopted?
Protocols are nice, but there is no way for C code to verify whether
a type's "protocol" structure actually implements some particular
protocol. As a result, you can pass an object that implements the
"vfs" protocol to one that expects the "stream" protocol, and the
opposite of awesomeness ensues.
This patch adds an OPTIONAL (but enabled by default) protocol identifier
as the first member of any protocol structure. This identifier is
simply a unique QSTR chosen by the protocol designer and used by each
protocol implementer. When checking for protocol support, instead of
just checking whether the object's type has a non-NULL protocol field,
use `mp_proto_get` which implements the protocol check when possible.
The existing protocols are now named:
protocol_framebuf
protocol_i2c
protocol_pin
protocol_stream
protocol_spi
protocol_vfs
(most of these are unused in CP and are just inherited from MP; vfs and
stream are definitely used though)
I did not find any crashing examples, but here's one to give a flavor of what
is improved, using `micropython_coverage`. Before the change,
the vfs "ioctl" protocol is invoked, and the result is not intelligible
as json (but it could have resulted in a hard fault, potentially):
>>> import uos, ujson
>>> u = uos.VfsPosix('/tmp')
>>> ujson.load(u)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ValueError: syntax error in JSON
After the change, the vfs object is correctly detected as not supporting
the stream protocol:
>>> ujson.load(p)
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: stream operation not supported
writeto_then_readfrom has been added to do a write -> no stop ->
repeated start -> read sequence. This is done to match the
capabilities of Blinka on Linux.
Code that uses stop=False will not work correctly on Blinka.
To fix, if stop=False then use writeto_then_readfrom otherwise use
writeto then readfrom_into.
First step in #2082
This also improves Palette so it stores the original RGB888 colors.
Lastly, it adds I2CDisplay as a display bus to talk over I2C. Particularly
useful for the SSD1306.
Fixes#1828. Fixes#1956
This started while adding USB MIDI support (and descriptor support is
in this change.) When seeing that I'd have to implement the MIDI class
logic twice, once for atmel-samd and once for nrf, I decided to refactor
the USB stack so its shared across ports. This has led to a number of
changes that remove items from the ports folder and move them into
supervisor.
Furthermore, we had external SPI flash support for nrf pending so I
factored out the connection between the usb stack and the flash API as
well. This PR also includes the QSPI support for nRF.
Particularly when they have buffers that are written via IRQ or DMA,
UART objects do not relocate gracefully. If such an object is
relocated to the long-lived pool after its original creation, the
IRQ or DMA will write to an unexpected location within the Python
heap, leading to a variety of symptoms. The most frequent symptom
is inability to read from the UART.
Consider the particular case of atmel-samd: usart_uart_obj_t
contains a usart_async_descriptor contains a _usart_async_device.
In _sercom_init_irq_param the address of this contained
_usart_async_device is assigned to a global array
sercom_to_sercom_dev which is later used from the interrupt context
_sercom_usart_interrupt_handler to store the received data in the
right ring buffer.
When the UART object is relocated to the long-lived heap, there's no
mechanism to re-point these internal pointers, so instead take the
cowardly way and allocate the UART object as long-lived.
Happily, almost all UART objects are likely to be long-lived, so
this is unlikely to have a negative effect on memory usage or heap
fragmentation.
Closes: #1056
1. UART: ported to ASF4. Allow rx-only and tx-only. Add .baudrate r/w property.
2. Make NeoPixel timing deterministic by turning off caches during NeoPixel writes.
3. Incorporate asf4 updates:
a. async USART driver
b. bringing Atmel START configuration closer to what we use
c. Clock initialization order now specified by CIRCUITPY_GCLK_INIT_1ST and _LAST.
4. supervisor/port.c: Move commented-out clock-test pin setting to correct location.
all: Add .frequency read-only property for busio.SPI to return actual frequency.
Fix esp8266/posix_helpers.c, which was not up to date for the new
long-lived/short-lived heap allocation scheme.
Also, fixed pin mappings for rev B Metro M4:
swap PA12 and PA13 on SPI 2x3 header
swap A3 and A5
Comment out all frozen modules in CPX again to make room while waiting
for SPI flash.
* Added asf4_conf/samd*/hpl_sercom_config.h
* Adjusted clocks in peripheral_clk_config.h.
* Put some frozen libs back in CPX for testing.
* Implement common-hal I2C
* Add samd*_peripherals.h in parallel with samd*_pins.h for common
functions and data.
* Store SERCOM index in pins table for convenience.
* Canonicalize some #include guard names in various .h files.
simpler reset of SERCOMs; remove unused routine
This is mostly for convenience, so that user code doesn't
need to add additional checks.
Also, bring the bitbangio into compatibility with busio wrt. empty
buffers.
Fixes for stmhal USB mass storage, lwIP bindings and VFS regressions
This release provides an important fix for the USB mass storage device in
the stmhal port by implementing the SCSI SYNCHRONIZE_CACHE command, which
is now require by some Operating Systems. There are also fixes for the
lwIP bindings to improve non-blocking sockets and error codes. The VFS has
some regressions fixed including the ability to statvfs the root.
All changes are listed below.
py core:
- modbuiltins: add core-provided version of input() function
- objstr: catch case of negative "maxsplit" arg to str.rsplit()
- persistentcode: allow to compile with complex numbers disabled
- objstr: allow to compile with obj-repr D, and unicode disabled
- modsys: allow to compile with obj-repr D and PY_ATTRTUPLE disabled
- provide mp_decode_uint_skip() to help reduce stack usage
- makeqstrdefs.py: make script run correctly with Python 2.6
- objstringio: if created from immutable object, follow copy on write policy
extmod:
- modlwip: connect: for non-blocking mode, return EINPROGRESS
- modlwip: fix error codes for duplicate calls to connect()
- modlwip: accept: fix error code for non-blocking mode
- vfs: allow to statvfs the root directory
- vfs: allow "buffering" and "encoding" args to VFS's open()
- modframebuf: fix signed/unsigned comparison pendantic warning
lib:
- libm: use isfinite instead of finitef, for C99 compatibility
- utils/interrupt_char: remove support for KBD_EXCEPTION disabled
tests:
- basics/string_rsplit: add tests for negative "maxsplit" argument
- float: convert "sys.exit()" to "raise SystemExit"
- float/builtin_float_minmax: PEP8 fixes
- basics: convert "sys.exit()" to "raise SystemExit"
- convert remaining "sys.exit()" to "raise SystemExit"
unix port:
- convert to use core-provided version of built-in import()
- Makefile: replace references to make with $(MAKE)
windows port:
- convert to use core-provided version of built-in import()
qemu-arm port:
- Makefile: adjust object-file lists to get correct dependencies
- enable micropython.mem_*() functions to allow more tests
stmhal port:
- boards: enable DAC for NUCLEO_F767ZI board
- add support for NUCLEO_F446RE board
- pass USB handler as parameter to allow more than one USB handler
- usb: use local USB handler variable in Start-of-Frame handler
- usb: make state for USB device private to top-level USB driver
- usbdev: for MSC implement SCSI SYNCHRONIZE_CACHE command
- convert from using stmhal's input() to core provided version
cc3200 port:
- convert from using stmhal's input() to core provided version
teensy port:
- convert from using stmhal's input() to core provided version
esp8266 port:
- Makefile: replace references to make with $(MAKE)
- Makefile: add clean-modules target
- convert from using stmhal's input() to core provided version
zephyr port:
- modusocket: getaddrinfo: Fix mp_obj_len() usage
- define MICROPY_PY_SYS_PLATFORM (to "zephyr")
- machine_pin: use native Zephyr types for Zephyr API calls
docs:
- machine.Pin: remove out_value() method
- machine.Pin: add on() and off() methods
- esp8266: consistently replace Pin.high/low methods with .on/off
- esp8266/quickref: polish Pin.on()/off() examples
- network: move confusingly-named cc3200 Server class to its reference
- uos: deconditionalize, remove minor port-specific details
- uos: move cc3200 port legacy VFS mounting functions to its ref doc
- machine: sort machine classes in logical order, not alphabetically
- network: first step to describe standard network class interface
examples:
- embedding: use core-provided KeyboardInterrupt object
buffer from start, end and length. The old code miscomputed length
leading to writing and reading from memory past the end of the buffer.
Consolidating the code should make it easier to get right everywhere.
* Track status pin use by user code separately so it can take over the pins and then give them back.
* Switch to hardware SPI for APA102 on Gemma and Trinket.
* Merge microcontroller/types.h into microcontroller/Pin.h to better match approach going forwards.
This was done to allow greatly granularity when deciding what functionality
is built into each board's build. For example, this way pulseio can be
omitted to allow for something else such as touchio.
