circuitpython/ports/atmel-samd/supervisor/port.c

366 lines
11 KiB
C
Raw Normal View History

/*
* This file is part of the MicroPython project, http://micropython.org/
*
* The MIT License (MIT)
*
* Copyright (c) 2017 Scott Shawcroft for Adafruit Industries
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
2019-12-06 15:18:20 -05:00
#include <string.h>
#include <stdlib.h>
#include "boards/board.h"
#include "supervisor/port.h"
// ASF 4
#include "atmel_start_pins.h"
#include "hal/include/hal_delay.h"
2019-12-06 15:18:20 -05:00
#include "hal/include/hal_flash.h"
#include "hal/include/hal_gpio.h"
#include "hal/include/hal_init.h"
#include "hpl/gclk/hpl_gclk_base.h"
#include "hpl/pm/hpl_pm_base.h"
#ifdef SAMD21
#include "hri/hri_pm_d21.h"
#endif
#ifdef SAMD51
#include "hri/hri_rstc_d51.h"
#endif
#include "common-hal/analogio/AnalogIn.h"
#include "common-hal/analogio/AnalogOut.h"
#include "common-hal/audiobusio/PDMIn.h"
#include "common-hal/audiobusio/I2SOut.h"
#include "common-hal/audioio/AudioOut.h"
#include "common-hal/busio/SPI.h"
#include "common-hal/microcontroller/Pin.h"
2018-02-14 19:59:04 -05:00
#include "common-hal/pulseio/PulseIn.h"
#include "common-hal/pulseio/PulseOut.h"
#include "common-hal/pulseio/PWMOut.h"
2019-05-15 22:29:34 -04:00
#include "common-hal/ps2io/Ps2.h"
#include "common-hal/rtc/RTC.h"
#if CIRCUITPY_TOUCHIO_USE_NATIVE
2018-05-22 17:20:35 -04:00
#include "common-hal/touchio/TouchIn.h"
#endif
#include "samd/cache.h"
#include "samd/clocks.h"
#include "samd/events.h"
#include "samd/external_interrupts.h"
#include "samd/dma.h"
#include "shared-bindings/rtc/__init__.h"
#include "reset.h"
#include "tick.h"
#include "supervisor/shared/safe_mode.h"
#include "supervisor/shared/stack.h"
#include "tusb.h"
#if CIRCUITPY_GAMEPAD
#include "shared-module/gamepad/__init__.h"
#endif
2019-04-16 13:11:54 -04:00
#if CIRCUITPY_GAMEPADSHIFT
#include "shared-module/gamepadshift/__init__.h"
#endif
2018-08-09 16:35:26 -04:00
#include "shared-module/_pew/PewPew.h"
extern volatile bool mp_msc_enabled;
#if defined(SAMD21) && defined(ENABLE_MICRO_TRACE_BUFFER)
// Stores 2 ^ TRACE_BUFFER_MAGNITUDE_PACKETS packets.
// 7 -> 128 packets
#define TRACE_BUFFER_MAGNITUDE_PACKETS 7
// Size in uint32_t. Two per packet.
#define TRACE_BUFFER_SIZE (1 << (TRACE_BUFFER_MAGNITUDE_PACKETS + 1))
// Size in bytes. 4 bytes per uint32_t.
#define TRACE_BUFFER_SIZE_BYTES (TRACE_BUFFER_SIZE << 2)
__attribute__((__aligned__(TRACE_BUFFER_SIZE_BYTES))) uint32_t mtb[TRACE_BUFFER_SIZE] = {0};
#endif
2019-12-06 15:18:20 -05:00
#if CALIBRATE_CRYSTALLESS
static void save_usb_clock_calibration(void) {
// If we are on USB lets double check our fine calibration for the clock and
// save the new value if its different enough.
SYSCTRL->DFLLSYNC.bit.READREQ = 1;
uint16_t saved_calibration = 0x1ff;
if (strcmp((char*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, "CIRCUITPYTHON1") == 0) {
saved_calibration = ((uint16_t *) CIRCUITPY_INTERNAL_CONFIG_START_ADDR)[8];
}
while (SYSCTRL->PCLKSR.bit.DFLLRDY == 0) {
// TODO(tannewt): Run the mass storage stuff if this takes a while.
}
int16_t current_calibration = SYSCTRL->DFLLVAL.bit.FINE;
if (abs(current_calibration - saved_calibration) > 10) {
// Copy the full internal config page to memory.
uint8_t page_buffer[NVMCTRL_ROW_SIZE];
memcpy(page_buffer, (uint8_t*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, NVMCTRL_ROW_SIZE);
// Modify it.
memcpy(page_buffer, "CIRCUITPYTHON1", 15);
// First 16 bytes (0-15) are ID. Little endian!
page_buffer[16] = current_calibration & 0xff;
page_buffer[17] = current_calibration >> 8;
// Write it back.
// We don't use features that use any advanced NVMCTRL features so we can fake the descriptor
// whenever we need it instead of storing it long term.
struct flash_descriptor desc;
desc.dev.hw = NVMCTRL;
flash_write(&desc, (uint32_t) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, page_buffer, NVMCTRL_ROW_SIZE);
}
}
#endif
safe_mode_t port_init(void) {
#if defined(SAMD21)
2018-05-03 23:43:02 -04:00
// Set brownout detection to ~2.7V. Default from factory is 1.7V,
// which is too low for proper operation of external SPI flash chips (they are 2.7-3.6V).
// Disable while changing level.
SYSCTRL->BOD33.bit.ENABLE = 0;
SYSCTRL->BOD33.bit.LEVEL = 39; // 2.77V with hysteresis off. Table 37.20 in datasheet.
SYSCTRL->BOD33.bit.ENABLE = 1;
#ifdef ENABLE_MICRO_TRACE_BUFFER
REG_MTB_POSITION = ((uint32_t) (mtb - REG_MTB_BASE)) & 0xFFFFFFF8;
REG_MTB_FLOW = (((uint32_t) mtb - REG_MTB_BASE) + TRACE_BUFFER_SIZE_BYTES) & 0xFFFFFFF8;
REG_MTB_MASTER = 0x80000000 + (TRACE_BUFFER_MAGNITUDE_PACKETS - 1);
#else
// Triple check that the MTB is off. Switching between debug and non-debug
// builds can leave it set over reset and wreak havok as a result.
REG_MTB_MASTER = 0x00000000 + 6;
#endif
#endif
2018-05-03 23:43:02 -04:00
#if defined(SAMD51)
// Set brownout detection to ~2.7V. Default from factory is 1.7V,
// which is too low for proper operation of external SPI flash chips (they are 2.7-3.6V).
// Disable while changing level.
SUPC->BOD33.bit.ENABLE = 0;
SUPC->BOD33.bit.LEVEL = 200; // 2.7V: 1.5V + LEVEL * 6mV.
SUPC->BOD33.bit.ENABLE = 1;
2018-05-07 21:55:37 -04:00
// MPU (Memory Protection Unit) setup.
// We hoped we could make the QSPI region be non-cachable with the MPU,
// but the CMCC doesn't seem to pay attention to the MPU settings.
// Leaving this code here disabled,
// because it was hard enough to figure out, and maybe there's
// a mistake that could make it work in the future.
#if 0
// Designate QSPI memory mapped region as not cachable.
// Turn off MPU in case it is on.
MPU->CTRL = 0;
// Configure region 0.
MPU->RNR = 0;
// Region base: start of QSPI mapping area.
// QSPI region runs from 0x04000000 up to and not including 0x05000000: 16 megabytes
MPU->RBAR = QSPI_AHB;
MPU->RASR =
0b011 << MPU_RASR_AP_Pos | // full read/write access for privileged and user mode
0b000 << MPU_RASR_TEX_Pos | // caching not allowed, strongly ordered
1 << MPU_RASR_S_Pos | // sharable
0 << MPU_RASR_C_Pos | // not cachable
0 << MPU_RASR_B_Pos | // not bufferable
0b10111 << MPU_RASR_SIZE_Pos | // 16MB region size
1 << MPU_RASR_ENABLE_Pos // enable this region
;
// Turn off regions 1-7.
for (uint32_t i = 1; i < 8; i ++) {
MPU->RNR = i;
MPU->RBAR = 0;
MPU->RASR = 0;
}
2018-05-03 23:43:02 -04:00
2018-05-07 21:55:37 -04:00
// Turn on MPU. Turn on PRIVDEFENA, which defines a default memory
// map for all privileged access, so we don't have to set up other regions
// besides QSPI.
MPU->CTRL = MPU_CTRL_PRIVDEFENA_Msk | MPU_CTRL_ENABLE_Msk;
#endif
samd_peripherals_enable_cache();
#endif
#ifdef SAMD21
hri_nvmctrl_set_CTRLB_RWS_bf(NVMCTRL, 2);
_pm_init();
#endif
2019-12-06 15:18:20 -05:00
#if CALIBRATE_CRYSTALLESS
uint32_t fine = DEFAULT_DFLL48M_FINE_CALIBRATION;
// The fine calibration data is stored in an NVM page after the text and data storage but before
// the optional file system. The first 16 bytes are the identifier for the section.
if (strcmp((char*) CIRCUITPY_INTERNAL_CONFIG_START_ADDR, "CIRCUITPYTHON1") == 0) {
fine = ((uint16_t *) CIRCUITPY_INTERNAL_CONFIG_START_ADDR)[8];
}
clock_init(BOARD_HAS_CRYSTAL, fine);
#else
// Use a default fine value
clock_init(BOARD_HAS_CRYSTAL, DEFAULT_DFLL48M_FINE_CALIBRATION);
#endif
// Configure millisecond timer initialization.
tick_init();
#if CIRCUITPY_RTC
rtc_init();
#endif
init_shared_dma();
// Reset everything into a known state before board_init.
reset_port();
// Init the board last so everything else is ready
board_init();
#ifdef SAMD21
if (PM->RCAUSE.bit.BOD33 == 1 || PM->RCAUSE.bit.BOD12 == 1) {
return BROWNOUT;
}
#endif
#ifdef SAMD51
if (RSTC->RCAUSE.bit.BODVDD == 1 || RSTC->RCAUSE.bit.BODCORE == 1) {
return BROWNOUT;
}
#endif
if (board_requests_safe_mode()) {
return USER_SAFE_MODE;
}
return NO_SAFE_MODE;
}
void reset_port(void) {
reset_sercoms();
#if CIRCUITPY_AUDIOIO
audio_dma_reset();
audioout_reset();
#endif
#if CIRCUITPY_AUDIOBUSIO
i2sout_reset();
//pdmin_reset();
2018-05-22 17:20:35 -04:00
#endif
#if CIRCUITPY_TOUCHIO && CIRCUITPY_TOUCHIO_USE_NATIVE
2018-05-22 17:20:35 -04:00
touchin_reset();
#endif
eic_reset();
#if CIRCUITPY_PULSEIO
pulseout_reset();
pwmout_reset();
#endif
#if CIRCUITPY_ANALOGIO
analogin_reset();
analogout_reset();
#endif
#if CIRCUITPY_RTC
rtc_reset();
#endif
reset_gclks();
#if CIRCUITPY_GAMEPAD
gamepad_reset();
#endif
2019-04-16 13:11:54 -04:00
#if CIRCUITPY_GAMEPADSHIFT
gamepadshift_reset();
#endif
2019-03-01 12:50:00 -05:00
#if CIRCUITPY_PEW
2018-08-01 09:29:26 -04:00
pew_reset();
#endif
reset_event_system();
reset_all_pins();
// Output clocks for debugging.
// not supported by SAMD51G; uncomment for SAMD51J or update for 51G
// #ifdef SAMD51
// gpio_set_pin_function(PIN_PA10, GPIO_PIN_FUNCTION_M); // GCLK4, D3
// gpio_set_pin_function(PIN_PA11, GPIO_PIN_FUNCTION_M); // GCLK5, A4
// gpio_set_pin_function(PIN_PB14, GPIO_PIN_FUNCTION_M); // GCLK0, D5
// gpio_set_pin_function(PIN_PB15, GPIO_PIN_FUNCTION_M); // GCLK1, D6
// #endif
2019-12-06 15:18:20 -05:00
#if CALIBRATE_CRYSTALLESS
if (tud_cdc_connected()) {
save_usb_clock_calibration();
}
2019-12-06 15:18:20 -05:00
#endif
}
void reset_to_bootloader(void) {
_bootloader_dbl_tap = DBL_TAP_MAGIC;
reset();
}
void reset_cpu(void) {
reset();
}
uint32_t *port_stack_get_limit(void) {
return &_ebss;
}
uint32_t *port_stack_get_top(void) {
return &_estack;
}
// Place the word to save 8k from the end of RAM so we and the bootloader don't clobber it.
#ifdef SAMD21
uint32_t* safe_word = (uint32_t*) (HMCRAMC0_ADDR + HMCRAMC0_SIZE - 0x2000);
#endif
#ifdef SAMD51
uint32_t* safe_word = (uint32_t*) (HSRAM_ADDR + HSRAM_SIZE - 0x2000);
#endif
void port_set_saved_word(uint32_t value) {
*safe_word = value;
}
uint32_t port_get_saved_word(void) {
return *safe_word;
}
/**
* \brief Default interrupt handler for unused IRQs.
*/
__attribute__((used)) void HardFault_Handler(void)
{
#ifdef ENABLE_MICRO_TRACE_BUFFER
// Turn off the micro trace buffer so we don't fill it up in the infinite
// loop below.
REG_MTB_MASTER = 0x00000000 + 6;
#endif
reset_into_safe_mode(HARD_CRASH);
while (true) {
asm("nop;");
}
}