b40d072648
[stm] implementation of audiopwmio
...
Based on nrf PWMAudioOut by @jepler and stm PulseOut by @hierophect
Tested on a Meowbit
2021-03-26 13:18:01 -04:00
2bc61b4580
Parenthesize double-division for clarity
2021-03-26 11:01:22 -05:00
231cb1ffd9
mimxrt10xx: Use the proper "betweenTransferDelay" (et al) values
...
Set the betweenTransferDelay to the SCK low-time, to avoid long pauses
between bytes (transfers) while preventing the last SCK cycle in a byte
from being a runt pulse.
Compared to an earlier revision of this change, which just set the delays
all to zero, this doesn't break using an AirLift, which was sensitive
to the runt pulses (the simple loopback-wire test didn't detect the problem)
2021-03-26 10:54:13 -05:00
1d48054aea
mimxrt10xx: Factor out "transfer_common"
...
.. and set the "MasterPcsContinuous" flag, which removes some of the
gap between bytes of a single SPI transaction
2021-03-26 10:04:35 -05:00
ffb70a8737
Freeze ESP32SPI into mimxrt1011_evk
...
.. so that it is more conveniently like the metro m7 for my testing
2021-03-26 10:01:53 -05:00
9e110f120a
mimxrt10xx: busio: cap SPI baudrate at 30MHz per datasheet
2021-03-26 10:01:53 -05:00
155b61f027
Merge pull request #4378 from Gadgetoid/patch-remove-rp2040-i2c-bitbang
...
RP2040: Remove short-write bitbang from I2C
2021-03-25 21:01:02 -04:00
0b212e2243
Add non M4 audiomixer support
2021-03-25 17:30:40 -05:00
da4dceea15
Fix 16MB Winbond names
2021-03-25 11:37:08 -07:00
aec0ef3cbf
Switch devices.h to nvm.toml data
2021-03-25 09:57:18 -07:00
e9ceb9263e
Merge pull request #4474 from jepler/fix-spi-frequency
...
mimxrt: SPI: Set the TCR value returned by MasterBaudSetRate
2021-03-25 08:59:21 -07:00
f79d60b205
Use GCC @file to shorten linker command length
...
This hopefully fixes linking on Windows with cmd.exe
2021-03-24 15:03:33 -07:00
b440883fe5
mimxrt: SPI: Set the TCR value returned by MasterBaudSetRate
...
without this, the baud rate could be wrong; in my testing, it was
low by a factor of 2 when requesating baudrate=1_000_000 (1MHz).
When passing the baudrate in to LPSPI_MasterInit, the setting is made
automatically, but LPSPI_MAster_SetBaudRate just returns it via the
out-parameter tcrPrescaleValue.
2021-03-24 13:33:21 -05:00
5314fddca0
remove duplicate RX/TX pin lines
2021-03-23 16:04:23 -05:00
c81007afb0
Merge pull request #4446 from tannewt/rp2040_flash
...
Switch RP2040 flash settings to nvm.toml
2021-03-23 15:18:29 -04:00
cde659651b
add brown out detect level
2021-03-23 19:17:45 +01:00
278d53c512
Merge pull request #4465 from anecdata/udp_server
...
swap recvfrom_into() port byte-order
2021-03-23 13:48:39 -04:00
36edc4bb89
Improve Winbond naming and correct board settings
2021-03-23 09:06:48 -07:00
c106b432c5
swap recvfrom_into() port byte-order
2021-03-22 20:03:26 -05:00
7867632a81
Merge remote-tracking branch 'adafruit/main' into rp2040_flash
2021-03-22 15:29:43 -07:00
f200e6a21e
Fix doc build and address feedback
2021-03-22 15:24:27 -07:00
36ae69ab6f
qtpy is more of a button than a switch! add itsybitsy rev C files
2021-03-21 18:44:32 -04:00
ebd6011633
add USBBOOT switch, move RX pin, re-enable UART (tested)
2021-03-21 14:58:18 -04:00
d8a2d69e10
Working deep sleep via RTC reset, with debug pins
2021-03-21 13:15:44 -04:00
4b42932188
Merge pull request #4449 from ladyada/main
...
adventure together with rotary trinkey
2021-03-20 13:37:31 -04:00
8884682cac
adventure together with rotary trinkey
2021-03-20 12:03:51 -04:00
4aea7f8f52
Add requirements-dev.txt for python deps
2021-03-19 15:22:23 -07:00
22906ac95e
Merge pull request #4442 from jepler/m7-reboot-bootloader
...
mimxrt1011: Fix reset-to-bootloader
2021-03-19 15:37:06 -05:00
3fcb6b278f
Merge pull request #4443 from jepler/evk-pins-dnp
...
imxrt1010_evk: Delete pins that are not connected
2021-03-19 15:36:36 -05:00
c0ec904c7a
Merge pull request #4441 from jepler/metro_m7_4mb
...
metro m7: another place to fix flash capacity
2021-03-19 12:42:35 -04:00
ee59c75f62
imxrt1010_evk: Delete pins that are not connected
...
There are DNP resistors on the MIMXRT1010-EVK board (see SCH-45852)
that lead to these pins on the arduino-style header not being connected
through. In theory someone could populate them, but as it the presence
of these names in the pins module caused problems when they didn't work
as expected.
Closes #3012
2021-03-19 11:29:32 -05:00
06743d91ed
mimxrt1011: Fix reset-to-bootloader
...
The definition of DBL_TAP_REG must match tinyuf2
2021-03-19 10:11:45 -05:00
d7a2ae9df7
fix stm compiler error
2021-03-19 11:04:46 -04:00
01a1cdf13a
update flash chip comment
2021-03-19 09:50:26 -05:00
1512ca520b
Fix PWMOut non-error handling and never reset
2021-03-19 09:57:21 -04:00
6abea8a4aa
another place to fix flash capacity
2021-03-19 08:41:28 -05:00
8293e1eedc
fix display rotation and position
2021-03-19 00:09:48 -04:00
47437cb415
make translate; fix display pins
2021-03-18 23:42:24 -04:00
ea82ca1d02
correct PID
2021-03-18 23:24:20 -04:00
4fc2866f45
bare-arm: Clean up the code, make it run on an F405, and add a README.
...
This commit simplifies and cleans up the bare-arm port, and adds just
enough system and library code to make it execute on an STM32F405 MCU.
The mpconfigport.h configuration is simplified to just specify those
configuration values that are different from the defaults. And the
addition of -fdata-sections and -ffunction-sections means the final
firmware is smaller than it previously was, by about 4200 bytes.
A README is also added.
Signed-off-by: Damien George <damien@micropython.org>
2021-03-19 14:20:26 +11:00
21c55f8e75
update funhouse pins for latest rev b
2021-03-18 23:14:59 -04:00
b2d913412f
merge from upstream
2021-03-18 23:14:43 -04:00
5d2b60cbf6
Redo RP2040 flash settings
...
This switches stage2 to C and uses Jinja to change the C code based
on flash settings from https://github.com/adafruit/nvm.toml . It
produces the fastest settings for the given set of external flashes.
Flash size is no longer hard coded so switching flashes with similar
capabilities but different sizes should *just work*.
This PR also places "ITCM" code in RAM to save the XIP cache for
code execution. Further optimization is possible. A blink code.py
still requires a number of flash fetches every blink.
Fixes #4041
2021-03-18 16:55:42 -07:00
2589515342
Merge pull request #4435 from jepler/metro-m7
...
Fixes for Metro M7
2021-03-18 17:56:12 -05:00
0b22a9397a
mimxrt: Quiet some warnings down in the sdk
...
Closes #2487
2021-03-18 16:54:11 -05:00
0ba0fae495
mimxrt: Enable USB Midi
...
Closes #2473
2021-03-18 16:54:11 -05:00
74243fd71a
metro_m7: Update board name, flash chip size
2021-03-18 16:54:11 -05:00
11e510a06a
Merge pull request #4419 from spe2/main
...
Add board definition for Sparkfun Pro Micro RP2040
2021-03-17 18:17:24 -07:00
719e8710f2
Merge pull request #4411 from mintakka/thingplus-rp2040
...
added board configuration for Sparkfun ThingPlus RP2040
2021-03-17 16:23:55 -05:00
b8d4f9655f
RP2040: Only bitbang 0-byte writes
...
The I2C.c for RP2040 included a special case for writes <=2 bytes to match the MicroPython implementation,
however RP2040 does support 1 and 2 byte reads, with only 0 bytes being the exception.
Signed-off-by: Philip Howard <phil@pimoroni.com>
2021-03-17 16:25:54 +00:00
bfc8c89536
Merge pull request #4403 from jepler/bitmap-read-2
...
bitmaptools: Add readinto, arrayblit
2021-03-17 07:57:31 -05:00
337727ba0c
renamed board folder to match board name in boards.yml
2021-03-16 21:10:10 -04:00
94fa8e8a60
disable bitmaptools on small board
2021-03-16 19:04:21 -05:00
75ba26ee7c
Merge pull request #4421 from kattni/led-pin
...
Adding LED for D13/L pin name.
2021-03-16 18:58:14 -05:00
6e5aea08a9
stm32/Makefile: Allow QSTR_DEFS,QSTR_GLOBAL_DEPENDENCIES to be extended.
...
So a board can provide custom qstr definitions if needed.
Signed-off-by: Damien George <damien@micropython.org>
2021-03-17 10:25:16 +11:00
1be5ca7881
Merge pull request #4130 from gamblor21/rp_dp_parallel
...
Add RP2040 displayio.ParallelBus Support
2021-03-16 13:49:55 -05:00
dcd9a8ab91
Update ports/raspberrypi/boards/sparkfun_pro_micro_rp2040/mpconfigboard.mk
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-16 10:54:20 -07:00
5bc132a209
Update ports/raspberrypi/boards/sparkfun_pro_micro_rp2040/mpconfigboard.h
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-16 10:54:15 -07:00
b5333f2bdf
Update ports/raspberrypi/boards/sparkfun_thingplus_rp2040/mpconfigboard.h
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-16 13:47:33 -04:00
3d15877639
Update ports/raspberrypi/boards/sparkfun_thingplus_rp2040/mpconfigboard.mk
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-16 13:47:21 -04:00
58679dc038
Merge remote-tracking branch 'origin/main' into bitmap-read-2
2021-03-16 12:21:50 -05:00
2b910b7292
Adding LED for D13/L pin name.
2021-03-16 12:14:40 -04:00
bc690d4070
Merge pull request #4415 from jepler/pre-commit-no-run-if-empty
...
pre-commit: code formatter fixes
2021-03-16 09:54:12 -05:00
0890b54cd9
More formatting
2021-03-16 08:29:04 -05:00
fb437d8280
Formatting fixes
2021-03-16 08:22:02 -05:00
3b01a65743
Fixed formatting
2021-03-16 08:14:49 -05:00
9de40f56f3
Add board config files
2021-03-15 22:08:19 -06:00
c9427780b3
Create pins.c
2021-03-15 22:07:24 -06:00
49baa94446
added sparkfun_thingplus_rp2040 to .github/workflows/boards.yml and renamed board folder to include chip
2021-03-15 23:00:24 -04:00
d53a6d58b0
stm32/Makefile: Fix C++ linker flags when toolchain has spaces in path.
...
The GNU Make dir command uses spaces as item separator so it does not
work for e.g building the STM32 port on Cygwin with a default Arm
installation in "c:/program files (x86)/GNU Arm Embedded Toolchain".
Fix by using POSIX dirname on a quoted path instead.
2021-03-16 12:54:16 +11:00
288415f867
Update ports/raspberrypi/boards/sparkfun_thingplus/mpconfigboard.h
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-15 21:07:31 -04:00
30a74b3d92
Update ports/raspberrypi/boards/sparkfun_thingplus/mpconfigboard.mk
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2021-03-15 21:07:24 -04:00
e326d7ca80
Merge branch 'main' into rp_dp_parallel
2021-03-15 20:00:13 -05:00
f7a988b9b3
Merge pull request #4405 from DavePutz/issue_4237
...
Issue 4237 - Changed initial setting in program_struct
2021-03-15 17:51:36 -07:00
9cb8ce67ed
Merge pull request #4412 from kamtom480/spi_and_i2c
...
spresense: minor changes for i2c, spi and uart
2021-03-15 17:35:06 -07:00
d3bf1fe15d
modifications by pre-commit
2021-03-15 18:11:00 -05:00
ed3f636be5
spresense: empty rx uart fifo after initialization
2021-03-15 16:14:16 +01:00
22ed0abf6c
spresens: configure pin mode for i2c and spi
2021-03-15 16:14:16 +01:00
0567d06936
added board configuration for Sparkfun ThingPlus RP2040
2021-03-15 10:27:21 -04:00
a52eb88031
run code formatting script
2021-03-15 19:27:36 +05:30
6c32a1f67f
update pins of senseBox MCU
2021-03-15 10:27:50 +01:00
b33d77bfe8
disable bitmaptools on over-full board
2021-03-14 20:08:09 -05:00
9a83501982
Fixed initial settings for program_struct to allow more than 1 program per pio
2021-03-14 15:05:56 -05:00
a9140ab09b
rp2: Use core-provided cmake fragments instead of custom ones.
...
Signed-off-by: Damien George <damien@micropython.org>
2021-03-14 15:53:18 +11:00
eccd73a403
extmod/extmod.cmake: Add modonewire.c to MICROPY_SOURCE_EXTMOD list.
...
Signed-off-by: Damien George <damien@micropython.org>
2021-03-14 15:51:28 +11:00
8e425a9354
Merge pull request #4393 from tannewt/raise_default_flash_speed
...
Speed up a bit more
2021-03-13 12:50:29 -05:00
dcaf702578
rp2/modmachine: Enable machine.Signal class.
...
Fixes issue #6863 .
Signed-off-by: Damien George <damien@micropython.org>
2021-03-14 00:19:04 +11:00
8010b15968
rp2: Enabled more core Python features.
...
This brings the port's configuration closer to the stm32 and esp32 ports.
Signed-off-by: Damien George <damien@micropython.org>
2021-03-14 00:17:22 +11:00
af45d511f1
rp2: Enable uerrno module.
...
Fixes #6991 .
2021-03-13 23:34:50 +11:00
1b106de4e0
Merge pull request #4262 from DavePutz/issue_4111
...
Issue 4111 - Implement pulseio(pulsein) for RP2040
2021-03-12 16:48:57 -08:00
45487f14a0
Speed up a bit more
2021-03-12 16:00:16 -08:00
96ce43e6d6
Added the correct files
2021-03-12 16:18:33 -06:00
6628f49852
Use StateMachine.c interrupt setup and simplify SM program
2021-03-12 16:06:57 -06:00
a5c6759325
Merge pull request #4392 from tannewt/lower_default_flash_speed
...
Lower default flash speed.
2021-03-12 13:58:44 -06:00
aec03a409f
Lower default flash speed.
...
/ 6 leads to ~40mhz. 2M and 4M have a max 0x03 read speed of 60mhz.
If the divisor is / 4 then the speed is just over 60mhz.
Fixes #4377
2021-03-12 11:06:39 -08:00
2009aecac3
Merge branch 'main' of github.com:felixerdy/circuitpython
2021-03-12 17:59:44 +01:00
de93df6444
add senseBox MCU
2021-03-12 17:57:55 +01:00
0ce5b2f594
put back pullup setting
2021-03-12 08:20:09 -05:00
6129b8e401
tests: Rename run-tests to run-tests.py for consistency.
...
Signed-off-by: Damien George <damien@micropython.org>
2021-03-12 19:56:09 +11:00
307d2a99fe
Fix after rebase
2021-03-11 20:06:50 -06:00
5689307798
Changed frequency to match PIO having 2 instructions
2021-03-11 19:32:44 -06:00
b02b1e9979
Set frequency default 60Mhz
2021-03-11 19:32:44 -06:00
1658fe04f9
Set the statemachine to never reset so REPL works
2021-03-11 19:32:44 -06:00
c384ebe5c0
Updated to initalize pindirs
2021-03-11 19:32:44 -06:00
7321411962
Added frequency to parallel display
2021-03-11 19:32:43 -06:00
56a219911f
Add frequency support to parallel bus
2021-03-11 19:32:43 -06:00
b080d6207b
Removing debug info and clean up
2021-03-11 19:32:43 -06:00
c6aaab6f64
Initial commit
2021-03-11 19:32:43 -06:00
c71b6cb699
move to esp-idf PR merge
2021-03-11 20:05:31 -05:00
b24fcd7aec
esp32/machine_hw_spi: Use default pins when making SPI if none given.
...
The default pins can be optionally configured by a board.
Fixes issue #6974 .
Signed-off-by: Damien George <damien@micropython.org>
2021-03-12 10:56:25 +11:00
6b2c9985ff
Extract RTC, implement fake RTC deepsleep
2021-03-11 17:50:05 -05:00
f75a009ed4
fix unnecessary statement order change
2021-03-11 15:16:32 -05:00
b5d2cc6f46
Merge remote-tracking branch 'adafruit/main' into esp32s2-i2c-bug
2021-03-11 15:09:18 -05:00
24f4d981bd
Merge pull request #4380 from jepler/rp2040-audiomp3
...
raspberrypi: Enable mp3 playback
2021-03-11 12:53:46 -06:00
0e451a1681
Merge pull request #4383 from hierophect/stm32-uart-dereserve
...
STM32: Fix UART deinit
2021-03-11 10:48:01 -08:00
40886d198d
Merge pull request #4385 from hierophect/stm32-f407-can
...
STM32: add all F405 modules to F407
2021-03-11 10:45:08 -08:00
de88fa37fb
Merge remote-tracking branch 'adafruit/main' into esp32s2-i2c-bug
2021-03-11 12:27:29 -05:00
061d5910cb
use fixed esp-idf
2021-03-11 12:09:01 -05:00
18668f6e28
spresense: fix spi to work with only one data pin
2021-03-11 18:06:49 +01:00
76d0870fba
spresense: return error as positive value for i2c
2021-03-11 18:04:01 +01:00
0b73c7a212
Update F407 to match F405
2021-03-11 11:27:17 -05:00
1ebbd14d0f
Fix UART deinit
2021-03-11 11:02:13 -05:00
15e97f12a1
Merge pull request #4379 from jepler/rp2040-rtc
...
raspberrypi: RTC: Ensure a time is set
2021-03-11 09:00:31 -06:00
b6489425c6
rp2/rp2_flash: Prevent MICROPY_HW_FLASH_STORAGE_BASE being set negative.
2021-03-12 00:57:29 +11:00
08c5dbb003
use return values in STM PWMOut constructor, not exceptions
2021-03-11 08:52:47 -05:00
c675452566
rp2/modmachine: Re-init UART for REPL on frequency change.
...
When UART is used for REPL and the MCU frequency is changed, the UART
has to be re-initialised. Besides that the UART may have to be recreated
after a frequency change, but with USB REPL this is not a problem.
Thanks to @HermannSW for spotting and providing the change.
2021-03-12 00:49:30 +11:00
11cf742524
rp2/modmachine: Allow changing CPU clock frequency.
...
Using the standard machine.freq().
The safe ranges tested were 10 and 12-270MHz, at which USB REPL still
worked. Requested settings can be checked with the script:
pico-sdk/src/rp2_common/hardware_clocks/scripts/vcocalc.py. At frequencies
like 300MHz the script still signaled OK, but USB did not work any more.
2021-03-12 00:48:46 +11:00
0461640983
rp2/rp2_pio: Fix sm.get(buf) to not wait after getting last item.
...
sm.get(buf) was waiting for one item more than the length of the supplied
buffer. Even if this item was not stored, sm_get would block trying to get
an item from the RX fifo.
As part of the fix, the edge case for a zero length buffer was moved up to
the section where the function arguments are handled. In case of a zero
length buffer, sm.get() now returns immediately that buffer.
2021-03-12 00:39:26 +11:00
a075e0b7d8
rp2/rp2_pio: Allow more than 8 consecutive pins for PIO out/set/sideset.
...
The bitmasks supplied for initialization of out/set/sideset were only 8 bit
instead of 32. This resulted in an error, that not more than 8 consecutive
pins would get initialized.
Fixes issue #6933 .
2021-03-12 00:26:32 +11:00
da85cb014a
rp2/machine_uart: Add support for inverted TX and RX lines.
...
Usage as in the other ports:
keyword "invert"
constants: INV_TX and INV_RX
Sample: uart = UART(1, invert=UART.INV_TX | UART.INV_RX)
2021-03-11 18:27:53 +11:00
8ade163fff
rp2/machine_uart: Add timeout/timeout_char to read and write.
2021-03-11 18:19:15 +11:00
8610bababe
rp2: Enable VfsFat class for FAT filesystem support.
...
Allows interfacing with SD cards, for example.
2021-03-11 17:56:21 +11:00
23ce25a7c3
mimxrt/boards: Add MIMXRT1050_EVK board, based on MIMXRT1060_EVK.
2021-03-11 16:42:38 +11:00
8785acac22
esp32/Makefile: Specify port and baud on erase_flash command.
2021-03-11 15:49:10 +11:00
16bfe3b41c
raspberrypi: RTC: Ensure a time is set
...
Until a time is set, the RTC is not running, and rtc_get_datetime()
returns false without assigning to the out-parameter.
In CircuitPython, this would manifest as arbitrary values being returned,
since uninitialized storage on the stack was being converted into a timestamp.
2021-03-10 20:20:40 -06:00
f0965b1ef7
Merge pull request #4350 from nitz/board-add-sparkfun-micromod-nrf52840
...
Add new nRF port for SF MicroMod nRF52840.
2021-03-10 18:13:11 -08:00
c95def0b32
raspberrypi: Enable mp3 playback
...
The rp2040 is _very_ marginal for mp3 playback, and currently sometimes triggers a bug that gives garbled audio output. However, it does work for some limited situations.
2021-03-10 18:44:10 -06:00
c33c749f64
stm32/boardctrl: Add MICROPY_BOARD_STARTUP hook.
...
Signed-off-by: Damien George <damien@micropython.org>
2021-03-11 09:04:36 +11:00
79c186f5c9
stm32/spi: Fix baudrate calculation for H7 series.
...
Fixes issue #6342 .
2021-03-11 01:06:52 +11:00
0facd891e7
stm32/powerctrl: Save and restore EWUP state when configuring standby.
...
This allows the user to enable wake-up sources using the EWUP bits, on F7
MCUs.
Disabling the wake-up sources while clearing the wake-up flags follows the
reference manual and ST examples.
2021-03-11 00:56:01 +11:00
85ea4ac0e5
stm32/main: Fix passing state.reset_mode to init_flash_fs.
...
state.reset_mode is updated by `MICROPY_BOARD_BEFORE_SOFT_RESET_LOOP` but
not passed to `init_flash_fs`, and so factory reset is not executed on
boards that do not have a bootloader. This bug was introduced by
4c3976bbcaFixes #6903 .
2021-03-10 23:50:40 +11:00
35c602d3b8
stm32/make-stmconst.py: Allow "[]" chars when parsing source comments.
...
For STM32WB MCUs, EXTI offset addresses were not parsed due to the
appearance of "[31:0]" in a comment in the .h file.
2021-03-10 23:44:02 +11:00
58fb011070
clean up
2021-03-10 19:03:27 +07:00
d1c6bb0927
rp2040 add double reset to uf2, also update pico-sdk to 1.1.0
2021-03-10 18:58:23 +07:00
a3c3e8a0fa
fix trailing whitespace
2021-03-09 22:41:08 -06:00
d5365cb066
SDIO/QSPI pin names. ¯\_(ツ)_/¯
2021-03-09 18:36:29 -05:00
5beb529f61
Update pins, remove unused defs from board config.
2021-03-09 17:43:13 -05:00
fe0655e121
Update pins, remove unused defs from board config.
2021-03-09 17:39:50 -05:00
0c58cc4772
Moved pin wait to an initial exec
2021-03-09 16:37:29 -06:00
1ae858126a
Fix the mpconfigboard.mk that was screwy?
2021-03-09 17:29:10 -05:00
d650849581
Merge pull request #4348 from FBSeletronica/franzininhoWIFI_wrover
...
Franzininho wifi ESP32-S2 Wrover
2021-03-09 13:07:19 -08:00
2c3002b327
Merge pull request #4370 from jposada202020/i2cperipheral_ctrlc
...
I2CPeripheral samd51 corrections in the CTRLC bit
2021-03-09 12:58:59 -08:00
a61db7f12e
Updated SparkFun MicroMod USB PID
...
As per the PID provide by TheHoff, [here](https://forum.sparkfun.com/viewtopic.php?p=223812#p223812 )
2021-03-09 12:54:52 -05:00
f0e3274a33
Update to agree with modified StateMachine.h
2021-03-09 11:13:09 -06:00
c6eb3f98be
Fixing build.yml
2021-03-09 13:55:20 -03:00
be90fa80e8
Initial Changes
2021-03-09 10:48:33 -05:00
6f4510d7aa
Merge branch 'main' into issue_4111
2021-03-08 23:28:21 -06:00
576da73a17
Added check for maxlen
2021-03-08 23:23:51 -06:00
95b7a59156
Merge branch 'issue_4111' of https://github.com/DavePutz/circuitpython into issue_4111
2021-03-08 23:22:05 -06:00
3db0fec267
Added check for maxlen
2021-03-08 23:20:57 -06:00
88650bc4d0
Removed leftover debug code
2021-03-08 22:48:57 -06:00
59a129f22f
stm32/storage: Prevent attempts to read/write invalid block addresses.
...
A corrupt filesystem may lead to a request for a block which is out of
range of the block device limits. Return an error instead of passing the
request down to the lower layer.
2021-03-09 15:32:50 +11:00
7029783985
funhouse board
2021-03-08 21:24:28 -05:00
775f1b9e0d
Merge pull request #4329 from jepler/rp2-rotaryio
...
raspberrypi: Implement rotaryio, improve StateMachine
2021-03-08 17:49:45 -08:00
4fc6c7d8c9
Merge pull request #4347 from FBSeletronica/franzininhoWIFI
...
Adding Circuitpython port for Franzininho WIFI board with the ESP32-S2 wroom module
2021-03-08 15:37:42 -08:00
c8f36e604c
reset myself, not go REPL, after wakeup from deep sleep.
2021-03-09 00:42:22 +09:00
27703f3156
fix quote error
2021-03-08 10:32:37 -03:00
fe29780afb
updating USB_VID and USB_PID for Espressif modules
2021-03-08 08:51:48 -03:00
2771e7fe75
Updating USB vendor ID and producfor Espressif modules
2021-03-08 08:47:33 -03:00
cdb0fda72a
Merge remote-tracking branch 'origin/main' into count-flash-devices
2021-03-07 20:26:04 -06:00
26eb429cc6
restore install/delete for i2c driver
2021-03-07 18:23:14 -05:00
f1ada8e880
Automatically count EXTERNAL_FLASH_DEVICES
2021-03-07 11:48:39 -06:00
a23129bc49
add GD25Q16C flash to BlackPill
2021-03-07 17:23:39 +00:00
a4133c4545
Merge pull request #4344 from jepler/vm-size-optimizations
...
Vm size optimizations: Get back 1500 bytes for 3.2% VM speed decrease
2021-03-07 10:09:51 -06:00
51c7a49853
Merge branch 'main' into nrf52-sleep
2021-03-07 20:50:53 +09:00
5bd1107fec
Clean up.
2021-03-07 20:38:04 +09:00
2eed9a1735
old System OFF sleep code for future reference.
2021-03-07 20:21:33 +09:00
7430b92d27
address hw pin-reset while sleep.
2021-03-07 20:20:29 +09:00
2795c002ad
disable QSPI while system ON idle loop.
2021-03-07 19:14:04 +09:00
cd5c0e99f7
Clean up.
2021-03-07 19:09:01 +09:00
3b76299f39
Add new nRF port for SF MicroMod nRF52840.
2021-03-07 01:06:50 -05:00
17aa9ae3f6
Update vendor ID for Espressif ESP32S2 Modules
2021-03-06 18:43:34 -03:00
4a50f1dd6f
Update Vendor ID for Espressif
2021-03-06 18:36:53 -03:00
48e727f7d6
adding port for Franzininho WIFI board ESP32S2 w/Wrover
2021-03-06 17:47:27 -03:00
6cf9c5158c
adding port for Franzininho WIFI board
2021-03-06 17:15:54 -03:00
3fab9f8b1b
new wait-until-alarm design, don't use System OFF.
2021-03-07 01:09:54 +09:00
4f040af481
vm: Make the speed-size trade-off compile time settable
...
.. and enable for all samd21 boards
2021-03-05 18:29:27 -06:00
67fb3054b4
Merge pull request #4342 from jamesbowman/main
...
Enable EVE low-level for Teensy 4.0 and 4.1
2021-03-05 17:25:00 -06:00
d2056a46ee
Merge pull request #4335 from tyomitch/main
...
[nrf] No need to store `buffer_length` as part of `audiopwmio_pwmaudioout_obj_t`
2021-03-05 15:54:10 -06:00
bed96a98d2
Merge pull request #4337 from tyomitch/patch-1
...
[stm] `curr_pulseout` can be `STATIC`
2021-03-05 15:53:31 -06:00
bff585ffd2
Enable EVE low-level for Teensy 4.0 and 4.1
2021-03-05 11:32:58 -08:00
cd1f19020f
raspberrypi: move landmine Makefile comments
2021-03-05 12:59:55 -06:00
2ae1e7de61
WIPrp2040: Implement IncrementalEncoder
...
Any two consecutive pins can be used for an IncrementalEncoder
Testing performed: Put a synthesized (few hundred counts per second) quadrature signal into GP2/3 and read the encoder out. Performed filesystem operations at the same time to stress test it.
The reasons for not using common_hal_rp2pio_statemachine_readinto are commented on.
2021-03-05 10:31:29 -06:00
4cf6579e22
remove general changes; not consistent across builds
2021-03-05 10:10:50 -05:00
e0b96c0f43
[nrf] No need to store `buffer_length` as part of `audiopwmio_pwmaudioout_obj_t`
2021-03-05 06:01:58 -05:00
4720dc179a
[stm] `curr_pulseout` can be `STATIC`
...
Not used outside of PulseOut.c
2021-03-05 12:52:13 +02:00
c97721455a
Shrink the smallest builds with compile options
2021-03-04 23:07:06 -05:00
a4dda3a5ba
Merge branch 'main' into issue_4111
2021-03-04 14:38:00 -06:00
c5c297d2c0
Update PulseOut.c
2021-03-04 13:53:19 -06:00
b7f03f9487
Update PulseOut.h
2021-03-04 13:52:40 -06:00
2d941b070f
Changed interrupt to per-word basis; cleaned up other small items
2021-03-04 13:51:46 -06:00
bc14ed31f6
StateMachine.h: Add header for declaration of mcu_pin_obj_t typedef
2021-03-04 12:28:46 -06:00
c023ec03ff
PDMIn: Add missing deinit call
2021-03-04 12:28:06 -06:00
bd01d31542
rp2pio: Add pins_are_sequential
...
This can be used where the standard API calls for a list of pins, to check that they satisfy the requirements of the rp2pio state machine, e.g.,
```python
def __init__(self, pin_a, pin_b):
if not rp2pio.pins_are_sequential([pin_a, pin_b]):
raise ValueError("Pins must be sequential")
```
2021-03-04 11:26:33 -06:00
ff62b0d2c0
StateMachine: Add pull up/down for inputs
2021-03-04 11:26:29 -06:00
68ac14b309
StateMachine: Add in_available property
...
I named the property `in_available` because it is similar to pyserial.
However, it indicates the number of words in the fifo, not the number
of bytes.
2021-03-04 11:14:09 -06:00
2ae8a44b2a
Merge pull request #4325 from microDev1/fix-wdt
...
ESP32S2: Fix watchdog deinit
2021-03-04 11:04:01 -05:00
6f99026a64
rp2040 use normal usb_irq_handler()
2021-03-04 21:29:04 +07:00
13453d35c6
fix watchdog deinit
2021-03-04 13:23:34 +05:30
71c43ca2dd
Merge pull request #4319 from jepler/feather-default-uart
...
feather rp2040: enable default board.UART
2021-03-03 16:46:00 -05:00
b0fca4fcda
feather rp2040: enable default board.UART
2021-03-03 13:13:06 -06:00
cd48c5ee83
Merge pull request #4315 from dhalbert/rp2040-i2c-short-writes
...
RP2040: Implement short I2C writes (2 bytes or less) using bitbangio
2021-03-03 12:42:47 -05:00
88353f2f5b
Update mpconfigport.mk
2021-03-03 11:00:58 -06:00
ced707ed32
Update call to rp2pio_statemachine_construct
2021-03-03 10:55:08 -06:00
514b73bcf8
Merge pull request #4254 from gamblor21/rp2040_countio
...
Rp2040 countio
2021-03-03 08:47:24 -08:00
1d8933dd05
Merge pull request #4265 from DavePutz/pio_soft_reset
...
Clear out PIOs and State Machines on RP2040 soft reset
2021-03-03 08:43:57 -08:00
fb7a0f7efc
add 1sec timeouts for I2C read and write
2021-03-03 09:43:57 -05:00
98075c5255
Fixed merge
2021-03-02 22:32:59 -06:00
e3ab394cd6
works on nearly all sensors
2021-03-02 23:27:37 -05:00
4167778bbc
Merge pull request #4312 from jepler/feather-rp2040-led
...
feather rp2040: add board.LED
2021-03-02 23:19:14 -05:00
9b96bae668
Update mpconfigport.mk
2021-03-02 21:36:00 -06:00
30d491e136
Update mpconfigport.mk
2021-03-02 21:30:49 -06:00
58fb7b9b32
Update mpconfigport.mk to get builds working
2021-03-02 21:27:46 -06:00
6046d37f31
Update PulseIn.c
2021-03-02 21:23:45 -06:00
37ee18349f
Merge branch 'main' into rp2040_countio
2021-03-02 19:47:53 -06:00
4246cc3f6d
Counter and PWMOut slice conflict check
2021-03-02 19:32:06 -06:00
b27afad9cb
move LED to the right spot in the file
2021-03-02 19:02:38 -06:00
efc2667b5f
Merge pull request #4186 from jepler/update-protomatter-rp2
...
Enable protomatter on RP2040 builds
2021-03-02 19:01:37 -06:00
15615effc2
Merge pull request #4276 from bergdahl/patch-1
...
Update StateMachine.c
2021-03-02 17:11:45 -05:00
0a58d451ad
Merge pull request #4306 from Neradoc/fix-reset-to-safe
...
press reset to safe mode on ports where reset reason is not implemented
2021-03-02 15:44:52 -05:00
f31b472309
Merge remote-tracking branch 'adafruit/main' into rp2040-i2c-short-writes
2021-03-02 15:17:12 -05:00
9939c59caa
wip
2021-03-02 15:16:55 -05:00
8bfd308d37
feather rp2040: add board.LED
2021-03-02 13:16:09 -06:00
e4f0e47d9f
Merge pull request #4233 from pewpew-game/displayio-group-list
...
displayio: make Group use a python list internally
2021-03-02 09:59:58 -08:00
ce70b95990
Merge pull request #4177 from microDev1/nvm-rp
...
RP2040: Support for NVM
2021-03-02 09:57:36 -08:00
248acd07c8
shrink builds
2021-03-02 12:25:42 -05:00
f41fb6fafc
Apply suggestions from code review
...
copyediting
2021-03-02 12:01:50 -05:00
9f6ebf3012
Merge pull request #4310 from kamtom480/spresense_analogin
...
spresense: return valid reference voltage
2021-03-02 11:55:42 -05:00
2651e15a52
Merge pull request #4309 from jepler/rp2040-interrupt-pio
...
rp2pio: allow keyboard interrupt while waiting for tx fifo to empty (& stall)
2021-03-02 08:55:27 -08:00
722a7150ca
Merge pull request #4308 from jepler/rp2040-build-boot2
...
raspberrypi: allow directly specifying the original boot .S file
2021-03-02 08:54:30 -08:00
f1792c8474
Extract EXTI, create base sleep framework
2021-03-02 11:41:53 -05:00
f560b5f3a3
raspberry: switch pico back to the boot2 for W25Q16
...
Presumably, switching it to generic hurt performance a bit.
I verified that the build-raspberry_pi_pico/boot2_padded_checksummed.S
built file has the same checksum as the old
bs2_default_padded_checksummed.S
2021-03-02 08:08:41 -06:00
7c921b808b
spresense: Define LONGINT_IMPL as MPZ
2021-03-02 14:25:22 +01:00
f9d21637a3
spresense: return valid reference voltage
2021-03-02 14:25:22 +01:00
cb2cf81136
ugame10 - disable pulseio to make more room for the French
2021-03-02 11:11:55 +01:00
b029031286
minor structural modification
2021-03-02 14:36:28 +05:30
54d11a8e2d
Merge pull request #4299 from jamesbowman/main
...
Add EVE support for Feather M4 Express
2021-03-01 22:56:50 -05:00
5a00862b1d
raspberrypi: allow directly specifying the original boot .S file
...
.. all the necessary steps to transform it into a padded, checksummed
file are now done by the build system.
Since it is assigned by "?=", it _should_ be the case that individual
builds can override it.
I did not "test" this per se, but it gives the same content and checksum
(except for the identifying comment with a path) as #4302 .
2021-03-01 21:08:19 -06:00
4b63a8c9b4
rp2pio: allow keyboard interrupt while waiting for tx fifo to empty (& stall)
2021-03-01 21:07:04 -06:00
d0eab5c561
Merge pull request #4256 from kmatch98/bt_cleanup
...
Add `bitmaptools` module
2021-03-01 18:24:12 -08:00
680ce45323
stm32/rfcore: Allow BLE settings to be changed by a board.
...
Two of the defaults have also changed in this commit:
- MICROPY_HW_RFCORE_BLE_LSE_SOURCE changed from 1 to 0, which configures
the LsSource to be LSE (needed due to errata 2.2.1).
- MICROPY_HW_RFCORE_BLE_VITERBI_MODE changed from 0 to 1, which enables
Viterbi mode, following all the ST examples.
Signed-off-by: Damien George <damien@micropython.org>
2021-03-02 12:14:54 +11:00
0dabd1ace2
Add EVE support for Feather M4 Express
2021-03-01 14:42:48 -08:00
1b3bca14cb
Merge pull request #4294 from kamtom480/spresense_analogin
...
spresense: return the correct value for Analog In
2021-03-01 13:21:15 -08:00
21a8752166
Merge pull request #4297 from adafruit/tannewt-patch-1
...
Update flash sizes for Adafruit RP2040 boards
2021-03-01 13:19:50 -08:00
238484ec26
Merge remote-tracking branch 'origin/main' into update-protomatter-rp2
2021-03-01 15:18:32 -06:00
532e7db293
Merge pull request #4267 from dhalbert/rp2040-digitalinout-fixes
...
RP2040: change DigitalInOut direction only when necessary; strong drive strength
2021-03-01 13:14:13 -08:00
af9dfccab1
Update QT Py flash size
2021-03-01 10:34:25 -08:00
dac047db61
Update Feather RP2040 to 8MB
2021-03-01 10:33:04 -08:00
d68fdf3a3d
spresense: return the correct value for Analog In
2021-03-01 15:45:10 +01:00
7cecd99658
remove unused debug printf's.
2021-02-28 16:04:29 +09:00
3e47e00291
address the pretending-to-deep-sleep issue.
2021-02-28 15:57:37 +09:00
498debc826
remove unused debug printf's.
2021-02-28 15:37:25 +09:00
9b34726c0d
GPIO and GPIOTE reg dump for debug.
2021-02-28 15:36:14 +09:00
d7bc8a46a5
Added counters per slice
2021-02-27 15:17:27 -06:00
29c89a2487
Removed more includes
2021-02-26 22:35:38 -06:00
f3515502b7
Removed unecessary includes
2021-02-26 22:33:50 -06:00
6374408c06
Changed reset_rp2pio_statemachine to clean up any PIO interrupts.
2021-02-26 22:28:50 -06:00
f7eac46c78
Update StateMachine.c
...
Changed woring to use max instead
2021-02-27 00:07:30 +01:00
776301c932
Typo fix: direcion -> direction
2021-02-26 15:03:56 -08:00
888a0c5f08
Merge pull request #4224 from microDev1/busio-uart-rp
...
RP2040: Support for UART
2021-02-26 14:57:23 -08:00
d9234ffa82
need to gpio_set_dir() at some point
2021-02-26 15:27:35 -05:00
7942932176
Requested changes
2021-02-26 14:14:55 -06:00
7562b0cbb8
Turn off GC opt on catwan_usbstick
2021-02-26 12:00:01 -08:00
2e6e91dc5c
Merge pull request #4253 from tannewt/rp2040_fix_pwm_reuse
...
Fix second shared PWM
2021-02-26 11:53:54 -08:00
7c8d7d77dd
Merge remote-tracking branch 'adafruit/main' into busio-uart-rp
2021-02-26 09:04:42 -08:00
caedc3bba6
Merge pull request #4270 from tannewt/rp2040_feather_pinout
...
Update RP2040 Feather pinout for production rev
2021-02-26 11:11:44 -05:00
1d1ff5f308
Merge remote-tracking branch 'origin/main' into update-protomatter-rp2
2021-02-26 09:56:35 -06:00
3f08cb47b8
Merge remote-tracking branch 'adafruit/main' into busio-uart-rp
2021-02-25 16:59:15 -08:00
52bc935fa7
A few minor fixes for corner cases
...
* Always clear the peripheral interrupt so we don't hang when full
* Store the ringbuf in the object so it gets collected when we're alive
* Make UART objects have a finaliser so they are deinit when their
memory is freed
* Copy bytes into the ringbuf from the FIFO after we read to ensure
the interrupt is enabled ASAP
* Copy bytes into the ringbuf from the FIFO before measuring our
rx available because the interrupt is based on a threshold (not
> 0). For example, a single byte won't trigger an interrupt.
2021-02-25 16:50:57 -08:00
f0432b9d6f
Remove neopixel power
2021-02-25 16:37:34 -08:00
0f8c96f424
remove trailing whitespaces.
2021-02-26 09:11:35 +09:00
7fd4648cd5
rase error if Alarm time >= 512 sec.
2021-02-26 09:06:11 +09:00
ec4cd68edc
More mpconfigboard.mk corrections for small builds
2021-02-25 17:48:50 -06:00
d0f1cfb039
address review; use gpio_set() carefully
2021-02-25 18:41:22 -05:00
277a67d876
call touchalarm funcs as well as pin/timealarm.
2021-02-26 08:11:50 +09:00
2b163ccd6a
Fix incorrect deinit mask
2021-02-25 14:57:46 -08:00
1b00d94b23
Fix second shared PWM
...
Fixes #4210
2021-02-25 14:49:09 -08:00
80f7972f72
Update RP2040 Feather pinout for production rev
2021-02-25 14:46:08 -08:00
22276710e6
rp2pio: Fix writing where the stride was 2 or 4
...
The wrong stride value was being checked.
2021-02-25 15:50:49 -06:00
a7a4f93ff8
Updated build configs to turn off BITMAPTOOLS for smaller builds
2021-02-25 15:44:32 -06:00
94d7bfb1c9
Merge pull request #4264 from UnexpectedCircuitPython/main
...
Expanded pin names for TinyS2 + FeatherS2 pin additions for DAC1 & DAC2
2021-02-25 15:13:18 -05:00
199a8ce8b0
change DigitalInOut direction only when necessary; strong drive strength
2021-02-25 14:10:19 -05:00
f8eb5bc275
Cleanup PIOs and State Machines on soft reset
2021-02-25 12:38:43 -06:00
8170e26a86
more uart improvements
...
- address suggested changes
- refine uart instance availibility checks
- improve pin validation and rx buffer handling
2021-02-25 23:46:00 +05:30
2aa5aec0d5
cleanup.
2021-02-26 01:45:12 +09:00
c713d31d0d
move externs to .h
2021-02-26 01:20:55 +09:00
bbe0602738
Merge pull request #4245 from kamtom480/spresense_usb_speed
...
spresense: Pass the correct USB bus speed after restart
2021-02-25 11:02:33 -05:00
c86ca2a4ff
move externs to .h
2021-02-26 00:51:52 +09:00
9328d09a7a
re-enable parameters check.
2021-02-26 00:50:44 +09:00
fb32e0a7fd
qtpy_m0_haxpress: Change config to make it fit.
2021-02-25 09:44:33 +01:00
69b10d7925
Added DAC1 & DAC2 pin names for FeatherS2
...
Expanded pin names for TinyS2 and added some new ones for functionality I forgot to add pin names for
Cleaned up mpconfigboard
2021-02-25 17:32:34 +11:00
86e60f5f35
Clean up formatting
2021-02-24 17:26:35 -06:00
61a69daae1
raise NotImplementedError when construct TouchAlarm.
2021-02-25 08:19:03 +09:00
17ff5dcc99
Return NotImplementedError for PulseOut
2021-02-24 17:04:05 -06:00
8e15f36baa
pulseio (pulsein) for RP2040
2021-02-24 16:58:29 -06:00
5d7fdafcde
implement suggested changes
...
- add internal buffering
- rtc initialization fix
2021-02-25 00:48:36 +05:30
f66896ce32
use nRF SDK function to set up memory retention.
2021-02-25 02:34:43 +09:00
e369473794
spresense: change RX and TX buffer size for CDC
2021-02-24 18:19:18 +01:00
9661d67cd3
replace MY_DEBUG_UART -> NRF_DEBUG_PRINT.
2021-02-25 01:49:57 +09:00
72b5f1a9a6
clean up my personal settings.
2021-02-25 01:38:23 +09:00
b935dcafdc
Merge branch 'main' into rp2040_countio
2021-02-23 19:46:41 -06:00
379f454ce6
Adding countio to rp2040
2021-02-23 19:38:05 -06:00
abbbb91fa8
Add state machine divisor check
...
This causes an exception when setting a state machine too slow or
too fast.
Fixes #4222
2021-02-23 16:30:46 -08:00
360475e266
Implement audiobusio and enhance PIO for it
...
This adds I2SOut and PDMIn support via PIO.
StateMachines can now:
* read and read while writing
* transfer in 1, 2 or 4 byte increments
* init pins based on expected defaults automatically
* be stopped and restarted
* rxfifo can be cleared and rxstalls detected (good for tracking when
the reading code isn't keeping up)
Fixes #4162
2021-02-23 15:50:00 -08:00
e41137c745
Merge pull request #4244 from UnexpectedCircuitPython/main
...
Added Unexpected Maker TinyS2 board definition
2021-02-23 10:40:06 -08:00
001d7299b2
Merge pull request #4228 from ZodiusInfuser/rp2040-boards
...
Added definitions for Pimoroni RP2040-based boards
2021-02-23 10:00:19 -08:00
0f188befb6
set RAM retention just before deep sleep
2021-02-24 00:12:25 +09:00
1a0bf4c33f
Added flash size for PicoSystem
2021-02-23 11:04:20 +00:00
a9951c9b6c
Added flash size for Keybow2040
2021-02-23 11:01:40 +00:00
ca9b7debe0
Added flash size for Tiny2040
2021-02-23 10:43:35 +00:00
78b2daa2a7
Added Unexpected Maker TinyS2 board definition
2021-02-23 17:55:17 +11:00
a30d4ad25d
set SUPEROPT_VM = 0 on most non-Express SAMD21 boards
2021-02-22 23:03:11 -05:00
ec64fa6a29
move dump_xxx functions to debug_uart.c.
2021-02-23 12:16:37 +09:00
372c98626a
move all the debug codes from port.c to debug_uart.c.
2021-02-23 11:56:40 +09:00
3fdf29e773
More parens
2021-02-22 18:35:09 -08:00
863981a5b8
Parens
2021-02-22 18:31:45 -08:00
9df0f439f3
alarm/pin/__init__.c is no longer used.
2021-02-23 10:31:49 +09:00
0aafeac209
Board specific flash sizes for RP2040
...
Stop-gap solution for #4041 . Comment is there to provide info
needed in the future. (We currently run the generic "safe" settings.)
2021-02-22 17:19:18 -08:00
53f5bb05a9
rp2,stm32: Enable MICROPY_PY_UBINASCII_CRC32 to get ubinascii.crc32().
...
These ports already have uzlib enabled so this additional ubinascii.crc32
function only costs about 90 bytes of flash.
Signed-off-by: Damien George <damien@micropython.org>
2021-02-23 10:13:25 +11:00
8470f0fdb7
SAMD21: one endpoint pair for MSC now instead of two
2021-02-21 12:37:59 -05:00
5c858a1925
add weak board_deinit().
2021-02-21 16:27:21 +09:00
75db0b9079
esp32: Define MICROPY_QSTRDEFS_PORT to include special qstrs.
...
Fixes issue #6942 .
Signed-off-by: Damien George <damien@micropython.org>
2021-02-21 15:56:54 +11:00
03a64f2077
stm32/boards/NUCLEO_WB55: Enable LPUART1 on PA2/PA3.
...
Signed-off-by: Damien George <damien@micropython.org>
2021-02-21 15:49:33 +11:00
9d674cf7ab
stm32/uart: Add support for LPUART1 on L0, L4, H7 and WB MCUs.
...
Add LPUART1 as a standard UART. No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:
STM32WB: LPUART1 = UART(2)
STM32L0: LPUART1 = UART(6)
STM32L4: LPUART1 = UART(6)
STM32H7: LPUART1 = UART(9)
On all ports: LPUART1 = machine.UART('LP1')
LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.
Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
2021-02-21 15:49:32 +11:00
1da8b9900a
Merge branch 'main' into nrf52-sleep
2021-02-21 13:35:06 +09:00
36c59250dd
some cleanups.
2021-02-21 09:57:14 +09:00
d659c2ce34
move port-specific debug functions from supervisor/shared/serial.c to ports/nrf/supervisor/port.c
2021-02-21 09:55:10 +09:00
793198909e
set SleepMemory size to 256 bytes.
2021-02-21 08:19:39 +09:00
41d9d4e0ab
call sd API only when sd enabled.
2021-02-21 08:17:57 +09:00
cf3217e6d4
Merge pull request #4232 from TG-Techie/fix_tg_watch
...
fix TG-Watch ble issue
2021-02-20 18:10:52 -05:00
a9a2145238
fix TG-Watch ble issue
2021-02-20 15:46:33 -05:00
52f2fd6d53
Removed trailing white space
2021-02-20 17:25:26 +00:00
417173b752
Removed trailing white space
2021-02-20 17:24:26 +00:00
9a4b8c5ed9
Removed trailing white space
2021-02-20 17:23:23 +00:00
dea498a51f
Added new line
2021-02-20 17:20:28 +00:00
9fbeb0baea
Added new line
2021-02-20 17:20:06 +00:00
03577ec81c
Added new line
2021-02-20 17:19:45 +00:00
dac81ea545
Added new line
2021-02-20 17:19:31 +00:00
0a00f91979
Added new line
2021-02-20 17:15:42 +00:00
f1df07002f
Added new line
2021-02-20 17:15:20 +00:00
Artyom Skrobov
Jeff Epler
Dan Halbert
gamblor21
Scott Shawcroft
Scott Shawcroft
felixerdy
Lucian Copeland
anecdata
lady ada
Jeff Epler
Jeff Epler
Dan Halbert
Damien George
Phil Howard
mintakka
Mark
spe2
Kattni Rembor
stijn
Kamil Tomaszewski
microDev
root
Kevin Köck
DavePutz
Andrew Scheller
robert-hh
StereoRocker
svetelna
Mike Causer
Reinhard Feger
Peter Hinch
Braiden Kindt
Herwin Grobben
hathach
nitz
FBSeletronica
jposada202020
Andrew Leech
jun2sak
jerryneedell
James Bowman
Radomir Dopieralski
Jonny Bergdahl
Kevin Matocha
Seon Rozenblum
ZodiusInfuser
Chris Mason
Jonah Yolles-Murphy