Commit Graph

22 Commits

Author SHA1 Message Date
MikeTeachman 1f6cb8f047 mixmrt/machine_i2s: Add I2S protocol support.
This commit adds support for machine.I2S on the mimxrt port.  The I2S API
is consistent with the existing stm32, esp32, and rp2 implementations.

I2S features:
- controller transmit and controller receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequencies from 8kHz to 48kHz
- 3 modes of operation:
  - blocking
  - non-blocking with callback
  - uasyncio
- configurable internal buffer
- optional MCK

Tested with the following development boards:
- MIMXRT1010_EVK, MIMXRT1015_EVK, MIMXRT1020_EVK, MIMXRT1050_EVK
- Teensy 4.0, Teensy 4.1
- Olimex RT1010
- Seeed ARCH MIX

Tested with the following I2S hardware peripherals:
- UDA1334
- GY-SPH0645LM4H
- WM8960 codec on board the MIMXRT boards and separate breakout board
- INMP441
- PCM5102
- SGTL5000 on the Teensy audio shield

Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
2022-03-30 14:12:40 +11:00
robert-hh 30380962cf mimxrt: Allow to select cs0 or cs1 for SPI.
Using the keyword argument cs=nnn in the constructor. The cs1
pin has to be defined in mpconfigboard.h.
Note: Only a few boards have the CS1 pin exposed to the connectors.
2022-01-27 16:53:30 +11:00
robert-hh 5ca56aaf16 mimxrt: Tidy up the board flash related files.
- Move the qspi_xxxx_flash_config.c files to hal.
  It turned out that they are less board than flash type specific.
- Change to a common flexspi_flash_config.h header file.
2021-12-14 20:31:20 +01:00
robert-hh bc1b0fd2c1 mimxrt: Define UART 0 on MIMXRT boards.
UART 0 is attached to the Debug USB port. The settings are
115200 Baud, 8N1.
For MIMXRT1010_EVK this is identical to UART1. For the other boards,
this is an additional UART.
2021-12-14 08:07:52 +01:00
robert-hh 7cc9b257a9 mimxrt/boards: Update the board.json files and add deploy_xx.md files.
- Add board.md files for MIMXRT1060_EVK and MIMXRT1064_EVK warning about
  their experimental state.
- Add separate deploy_teensy.md and deploy_mimxrt.md files.
2021-11-16 23:17:42 +11:00
Mike Causer 7f14344428 ports: Add images, features and urls to board.json. 2021-10-28 15:25:38 +11:00
Jim Mussared e359b077dd ports: Add board.json for all boards.
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.

Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.

Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
2021-10-27 14:04:53 +11:00
robert-hh 68146aa197 mimxrt/boards: Fix the D14/D15 pin assignment of MIMXRT1050/60/64_EVK.
There are several PCB layouts in the market under the same name.
2021-10-25 15:50:38 +11:00
robert-hh 1866ed7e2e mimxrt/eth: Add LAN support and integrate the network module.
This commit implements 10/100 Mbit Ethernet support in the mimxrt port.

The following boards are configured without ETH network:
- MIMXRT1010_EVK
- Teensy 4.0

The following boards are configured with ETH network:
- MIMXRT1020_EVK
- MIMXRT1050_EVK
- MIMXRT1060_EVK
- MIMXRT1064_EVK
- Teensy 4.1

Ethernet support tested with TEENSY 4.1, MIMRTX1020_EVK and MIMXRT1050_EVK.
Build tested with Teensy 4.0 and MIMXRT1010_EVK to be still working.
Compiles and builds properly for MIMXRT1060_EVK and MIMXRT1064_EVK, but not
tested lacking suitable boards.

Tested functions are:
- ping works bothway
- simple UDP transfer works bothway
- ntptime works
- the ftp server works
- secure socker works
- telnet and webrepl works

The MAC address is 0x02 plus 5 bytes from the manifacturing info field,
which can be considered as unique per device.

Some boards do not wire the RESET and INT pin of the PHY transceiver.  For
operation, these are not required.  If they are defined, they will be used.
2021-10-25 15:14:26 +11:00
Philipp Ebensberger 7e62c9707a mimxrt/sdram: Add SDRAM support.
Adds support for SDRAM via `SEMC` peripheral. SDRAM support can be
enabled in the mpconfigboard.mk file by setting `MICROPY_HW_SDRAM_AVAIL`
to `1` and poviding the size of the RAM via `MICROPY_HW_FLASH_SIZE`.

When SDRAM support is enabled the whole SDRAM is currently used used
for MicroPython heap.

Signed-off-by: Philipp Ebensberger
2021-10-22 08:23:24 +02:00
Philipp Ebensberger 0d7366c912 mimxrt: Rework flash configuration.
- Moves definition of BOARD_FLASH_SIZE and other header files related to
	flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
	required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
	QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
	both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
	linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.

With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.

Signed-off-by: Philipp Ebensberger
2021-09-14 13:52:52 +02:00
Philipp Ebensberger 87f97e490c mimxrt/sdcard: Implement SDCard driver.
- Configures `PLL2->PFD0` with **198MHz** as base clock of
	`USDHCx` peripheral.
- Adds guards for SDCard related files via `MICROPY_PY_MACHINE_SDCARD`
- Adds creation of pin defines for SDCard to make-pins.py
- Adds new configuration option for SDCard peripheral pinout
        to mpconfigport.h
- Adds interrupt handling support instead of polling
- Adds support for `ADMA2` powered data transfer
- Configures SDCard to run in HS (high-speed mode) with **50MHz** only!

SDCard support is optional and requires `USDHC` peripheral.
Thus this driver is not available on `MIMXRT1010_EVK`.
SDCard support is enabled by setting `MICROPY_PY_MACHINE_SDCARD = 1`
in mpconfigboard.mk.

Signed-off-by: Philipp Ebensberger
2021-09-07 20:45:33 +02:00
robert-hh 1074c784b0 mimxrt: Add support for Hyperflash chips.
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.

This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
  hyperflash.
- minor incidental changes to other boards so they still build

Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
2021-07-31 16:25:40 +10:00
robert-hh 98c5703027 mimxrt/machine_i2c: Add hardware-based machine.I2C to machine module.
It uses non-blocking transfer of data.  Advantage over SoftI2C:
- Higher data rate up to ~3 MHZ.
- Full protocol support.
2021-07-15 00:36:31 +10:00
robert-hh f45412793e mimxrt/machine_spi: Add the SPI class to the machine module.
This class supports SPI bus controller mode, with blocking transfers.

SPI device numbers start at 0, to comply with the pinout of the Teensy
boards.  With the configured clock frequency the fastest baud rate is
33MHz.  For messages longer 16 bytes DMA is used.  The class uses the
existing framework with extmod/machine_spi.c.

Extended driver options:

- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
  Since the pins used by the SPI are fixed, no Pin settings can be made.
  Thus the drive option is added allowing to control ringing and crosstalk
  on the connection.

- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
  Default is 2 clock cycles.
2021-06-26 22:14:47 +10:00
robert-hh 7417c6ac91 mimxrt/machine_pin: Implement pin.irq() functionality. 2021-06-16 01:42:10 +10:00
robert-hh 689476c576 mimxrt/machine_uart: Add the UART class to the machine module.
The implementation uses the LPUARTx devices.  Up to 8 UARTs can be used,
given that the pins are accessible.  E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.

For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1.  All other UART are assigned to different Pins:

MIMXRT1010-EVK:
    D0/D1   UART 1
    D6/D7   UART 2
    A0/D4   UART 3

MIMXRT1020-EVK:
    D0/D1   UART 1
    D6/D9   UART 2
    D10/D12 UART 3
    D14/D15 UART 4
    A0/A1   UART 5

MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
    D0/D1   UART 1
    D7/D6   UART 2
    D8/D9   UART 3
    A1/A0   UART 4
2021-06-16 01:21:15 +10:00
robert-hh a40e1473dc mimxrt: Add floating point support.
Since not all boards support double fp, all board specific .mk files are
affected too.
2021-06-04 00:37:22 +10:00
robert-hh dfd4324eb1 mimxrt: Add flash storage support with VFS and littlefs filesystem.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.

Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS.  VFS
  will take up most of the available flash. 1M is reserved for code.  9K is
  reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c.  All flashing
  related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
  module.

It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.

Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
2021-06-01 23:42:57 +10:00
Philipp Ebensberger ff5d39529c mimxrt: Implement machine.Pin class.
- modified pin type from pin_obj_t to machine_pin_obj_t
- created machine_pin.c
- implemented basic version of make-pins.py to genertate pins.c/.h files
  automatically; the only alternate function currently supported is GPIO
- added af.csv files for all supported MCUs
- replaced pins.c/pins.h files with pin.csv for all boards
- implemented on/off/high/low/value/init methods
- Implemented IN/OUT/OPEN_DRAIN modes
- modified LDFLAGS for DEBUG build to get usefull .elf file for debugging

Signed-off-by: Philipp Ebensberger
2021-05-26 00:12:42 +10:00
Albort Xue e0d539f79d mimxrt/boards: Enable LED class for MIMXRT1060_EVK board. 2020-06-09 18:51:08 +10:00
Albort Xue b3bc9808f2 mimxrt/boards: Add MIMXRT1060_EVK board. 2020-05-27 16:49:52 +10:00