Otherwise there is really nothing that can be done, it can't be unlocked by
the user because there is no way to allocate memory to execute the unlock.
See issue #4205 and #4209.
All concrete network classes are now moved to their own file (eg
network.WLAN.rst) and deconditionalised (remove ..only:: directives). This
makes the network documentation the same for all ports. After this change
there are no more "..only::" directives for different ports, and the only
difference among ports is the very front page of the docs.
The WiPy machine.Timer class is very different to the esp8266 and esp32
implementations which are better candidates for a general Timer class. By
moving the WiPy Timer docs to a completely separate file, under a new name
machine.TimerWiPy, it gives a clean slate to define and write the docs for
a better, general machine.Timer class. This is with the aim of eventually
providing documentation that does not have conditional parts to it,
conditional on the port.
While the new docs are being defined it makes sense to keep the WiPy docs,
since they describe its behaviour. Once the new Timer behaviour is defined
the WiPy code can be changed to match it, and then the TimerWiPy docs would
be removed.
The machine module should be standard across all ports so should have the
same set of classes in the docs. A special warning is added to the top of
the machine.SD class because it is not standardised and only available on
the cc3200 port.
It's fair to just provide a link to all available modules, regardless of
the port. Most of the existing ports (unix, stm32, esp8266, esp32) share
most of the same set of modules anyway, so no need to maintain separate
lists for them. And there's a big discussion at the start of this index
about modules not being available on a given port.
For port-specific modules, they can also be listed unconditionally because
they have headings that explicitly state they are only available on certain
ports.
The UART.init() method is now included unconditionally and its wording
adjusted to better describe ports other than the cc3200.
UART.irq() is also included unconditionally, but this is currently only
available on the WiPy target.
By virtue of its name, the pyb module would only be available on a pyboard
and so does not need to have conditional "only" directives throughout its
documentation.
These conditionals were added mostly in
cfcf47c064 in the initial development of the
cc3200 port, which had the pyb module before it switched to the machine
module. And wipy only conditionals were removed from the pyb module
documentation in 4542643025, so there's no
need to retain any more conditionals.
Allow including crypto consts based on compilation settings. Disabled by
default to reduce code size; if one wants extra code readability, can
enable them.
These can be optionally specified, but all ports are expected to be able to
accept them, at the very least ignore, though handling of "type" param
(SOCK_STREAM vs SOCK_DGRAM) is recommended.
This can be used to select the output buffer behaviour of the DAC. The
default values are chosen to retain backwards compatibility with existing
behaviour.
Thanks to @peterhinch for the initial idea to add this feature.
The parameter order in the example for ticks_diff was incorrect. If it's
"too early" that means that scheduled time is greater than current time and
if it's "running late" then scheduled time would be less than current time.
Put offset first in OR expressions, and use "offset" var instead of
hardcoded numbers. Hopefully, this will make it more self-describing
and show patterns better.
Introduction of ports subdirectory where all ports are moved to
The main change in this release is the introduction of a "ports/"
subdirectory at the top-level of the repository, and all of the ports are
moved here. In the process the "stmhal" port is renamed to "stm32" to
better reflect the MCU that it targets. In addition, the STM32 CMSIS and
HAL sources are moved to a new submodule called "stm32lib".
The bytecode has changed in this release, compared to the previous release,
and as a consequence the .mpy version number has increased to version 3.
This means that scripts compiled with the previous mpy-cross must be
recompiled to work with this new version.
There have also been various enhancements and optimisations, such as:
check for valid UTF-8 when creating str objects, support for reverse
special binary operations like __radd__, full domain checking in the math
module, support for floor-division and modulo in the viper emitter,
and addition of stack overflow checking when executing a regex.
The stm32 port sees improved support for F7 MCUs, addition of a new board
B_L475E_IOT01A based on the STM32L475, and support for the Wiznet W5500
chipset along with improved socket behaviour.
A detailed list of changes follows.
py core:
- objstr: startswith, endswith: check arg to be a string
- nlrx86,x64: replace #define of defined() with portable macro usage
- objtype: handle NotImplemented return from binary special methods
- objtype: mp_obj_class_lookup: improve debug logging
- map: remove unused new/free functions
- make m_malloc_fail() have void return type, since it doesn't return
- modstruct: in struct.pack, stop converting if there are no args left
- modstruct: check and prevent buffer-read overflow in struct unpacking
- modstruct: check and prevent buffer-write overflow in struct packing
- nlrthumb: get working again on standard Thumb arch (ie not Thumb2)
- objfloat: fix binary ops with incompatible objects
- obj: fix comparison of float/complex NaN with itself
- objtype: implement fallback for instance inplace special methods
- objtuple: properly implement comparison with incompatible types
- objstr: add check for valid UTF-8 when making a str from bytes
- objlist: properly implement comparison with incompatible types
- runtime0.h: move relational ops to the beginning of mp_binary_op_t
- runtime0.h: move MP_BINARY_OP_DIVMOD to the end of mp_binary_op_t
- objtype: make sure mp_binary_op_method_name has full size again
- runtime0.h: put inplace arith ops in front of normal operations
- builtinhelp: simplify code slightly by extracting object type
- runtime: implement dispatch for "reverse op" special methods
- nlrx86: fix building for Android/x86
- builtinhelp: change signature of help text var from pointer to array
- runtime.h: change empty mp_warning macro so var-args are non empty
- modbuiltins: implement abs() by dispatching to MP_UNARY_OP_ABS
- {objfloat,objcomplex}: optimise MP_UNARY_OP_ABS by reusing variables
- mpconfig.h: add note that using computed gotos in VM is not C99
- objstr: strip: don't strip "\0" by default
- objexcept: prevent infinite recursion when allocating exceptions
- stream: remove unnecessary checks for NULL return from vstr_add_len
- vstr: raise a RuntimeError if fixed vstr buffer overflows
- vm: use lowercase letter at start of exception message
- persistentcode: define mp_raw_code_save_file() for any unix target
- add config option to print warnings/errors to stderr
- objfloat: support raising a negative number to a fractional power
- objset: simplify set and frozenset by separating their locals dicts
- objset: check that RHS of a binary op is a set/frozenset
- objset: include the failed key in a KeyError raised from set.remove
- objtype: change type of enum-to-qstr table to uint16_t to save space
- objstr: make empty bytes object have a null-terminating byte
- mpprint: only check for null string printing when NDEBUG not defined
- objtype: clean up unary- and binary-op enum-to-qstr mapping tables
- persistentcode: bump .mpy version number to version 3
- bc: update opcode_format_table to match the bytecode
- modmath: add full checks for math domain errors
- modmath: convert log2 macro into a function
- formatfloat: don't print the negative sign of a NaN value
- formatfloat: use standard isinf, isnan funcs instead of custom ones
- modbuiltins: use existing utf8_get_char helper in builtin ord func
- emitnative: implement floor-division and modulo for viper emitter
- objtype: use CPython compatible method name for sizeof
- objtype: fit qstrs for special methods in byte type
- objtype: define all special methods if requested
- objtype: introduce MICROPY_PY_ALL_INPLACE_SPECIAL_METHODS
extmod:
- modubinascii: only include uzlib/tinf.h when it's really needed
- modussl_mbedtls: allow to compile with MBEDTLS_DEBUG_C disabled
- machine_pinbase: put PinBase singleton in ROM
- re1.5: upgrade to v0.8.2, adds hook for stack overflow checking
- modure: add stack overflow checking when executing a regex
- uos_dupterm: update uos.dupterm() and helper funcs to have index
- uos_dupterm: swallow any errors from dupterm closing the stream
- vfs: replace VLA in proxy func with small, static sized array
- modussl: add finaliser support for ussl objects
- modussl_mbedtls: allow to compile with unix coverage build
lib:
- add new submodule, stm32lib containing STM32 CMSIS and HAL source
- embed/abort_: use mp_raise_msg helper function
- libm: fix tanhf so that it correctly handles +/- infinity args
- libm: remove implementation of log2f, use MP_NEED_LOG2 instead
- axtls: update, support for SSL_EAGAIN return code
- berkeley-db-1.xx: update, allow to override MINCACHE, DEFPSIZE
drivers:
- memory/spiflash: change from hard-coded soft SPI to generic SPI
- display/ssd1306.py: improve performance of graphics methods
- nrf24l01: make nRF24L01 test script more portable
- display/ssd1306: implement SSD1306_I2C poweron method
- display/ssd1306: make poweron() work the same with SSD1306_SPI
- wiznet5k: improve the performance of socket ops with threading
- wiznet5k: get low-level W5500 driver working
tools:
- upip: upgrade to 1.2.2
- pyboard: use repr() when quoting data in error messages
- pyboard: update docstring for additional device support
tests:
- object_new: better messages, check user __new__() method
- class_new: add checks for __init__ being called and other improvements
- class_new: add another testcase for __new__/__init__ interaction
- class_inplace_op: test for inplace op fallback to normal one
- run-bench-tests: update locations of executables, now in ports/
- class_reverse_op: test for reverse arith ops special methods
- run-tests: skip class_inplace_op for minimal profile
- run-tests: fix copy-paste mistake in var name
- cpydiff: add cases for locals() discrepancies
- extmod: add test for ure regexes leading to infinite recursion
- extmod: add test for '-' in character class in regex
- run-tests: close device under test using "finally"
- net_inet: update tls test to work with CPython and incl new site
unix port:
- rename modsocket.c to modusocket.c
- modusocket: remove #if MICROPY_SOCKET_EXTRA code blocks
- enable MICROPY_PY_REVERSE_SPECIAL_METHODS
stm32 port:
- modmachine: make machine.bootloader() work when MPU is enabled
- modmachine: improve support for sleep/deepsleep on F7 MCUs
- compute PLL freq table during build instead of at run time
- modmachine: for F7 MCU, save power by reducing internal volt reg
- boards/pllvalues.py: make script work with both Python 2 and 3
- Makefile: use lib/stm32lib instead of local cmsis and hal files
- remove cmsis and hal files, they are now a submodule
- Makefile: automatically fetch stm32lib submodule if needed
- update to new STM Cube HAL library
- fix clock initialisation of L4 MCUs
- rename stmhal port directory to stm32
- remove unused usbd_msc.c file
- boards: change remaining stm32f4xx_hal_conf.h to unix line ending
- boards: change linker scripts to use "K" instead of hex byte size
- boards: fix I2C1 pin mapping on NUCLEO_F401RE/F411RE boards
- i2c: when scanning for I2C devices only do 1 probe per address
- modnwwiznet5k: release the GIL on blocking network operations
- boards: add new board B_L475E_IOT01A based on STM32L475
- make-stmconst.py: make sure mpz const data lives in ROM
- timer: make pyb.Timer() instances persistent
- mpconfigport.h: add configuration for max periphs on L4 series
- usbdev: make the USBD callback struct const so it can go in ROM
- usbdev: change static function variable to non-static
- usbdev: put all CDC state in a struct
- usbdev: put all HID state in a struct
- usbdev: simplify CDC tx/rx buffer passing
- usbdev: simplify HID tx/rx buffer passing
- usbdev/core: add state parameter to all callback functions
- usbdev: put all state for the USB device driver in a struct
- usbdev: simplify pointers to MSC state and block dev operations
- usbdev: merge all global USB device state into a single struct
- usbdev: make device descriptor callbacks take a state pointer
- usbdev: move all the USB device descriptor state into its struct
- timer: enable ARPE so that timer freq can be changed smoothly
- modnwwiznet5k: get the IP address of an established socket
- boards: fix typos in stm32f767_af.csv table
- usbd_cdc_interface: don't reset CDC output buf on initialisation
- modnwwiznet5k: implement WIZNET5K.isconnected() method
- modusocket: make getaddrinfo() work when passed an IP address
- modusocket: return OSError(-2) if getaddrinfo fails
- mpconfigport.h: add MICROPY_THREAD_YIELD() macro
- modnwwiznet5k: add support for W5500 Ethernet chip
- modnwwiznet5k: increase SPI bus speed to 42MHz
- modnwwiznet5k: implement stream ioctl for the Wiznet driver
- mphalport: improve efficiency of mp_hal_stdout_tx_strn_cooked
- make uos.dupterm() conform to specs by using extmod version
cc3200 port:
- enable micropython.kbd_intr() method
- use standard implementation of keyboard interrupt
esp8266 port:
- rename axtls_helpers.c to posix_helpers.c
- posix_helpers: set ENOMEM on memory alloc failure
- set DEFPSIZE=1024, MINCACHE=3 for "btree" module
- esp_mphal: send data in chunks to mp_uos_dupterm_tx_strn
- modnetwork: add "bssid" keyword arg to WLAN.connect() method
- modules/webrepl_setup: add info about allowed password length
zephyr port:
- Makefile: revamp "test" target after ports were moved to ports/
- use CONFIG_NET_APP_SETTINGS to setup initial network addresses
- switch to interrupt-driven pull-style console
pic16bit port:
- add definition of SEEK_SET to unistd.h
docs:
- pyboard/tutorial: add "timeout=0" to UART in pass-through example
- more xrefs to "MicroPython port" in glossary
- library/network: fix ref to "socket" module (should be "usocket")
- machine.Signal: improve style/grammar and add usage example
- library: add description of "index" parameter to uos.dupterm()
- library/micropython: fix typo in RST formatting
- library/framebuf.rst: generalise constructor to all colour formats
- btree: describe page caching policy of the underlying implementation
- esp8266/tutorial: update neopixel with example of using 4 bbp
- library/network: clarify usage of "bssid" arg in connect() method
- pyboard/quickref: add info for Switch, RTC, CAN, Accel classes
- pyboard/tutorial: update now that yellow LED also supports PWM
- esp8266/quickref: add quickref info for RTC class
- library: add missing cross-ref links for classes in pyb module
- library/network: update docs to state that W5500 is supported
- uselect: document one-shot polling mode
- usocket: elaborate descriptions
- usocket: document inet_ntop(), inet_pton()
- library/network: add dhcp_hostname parameter
- reference/isr_rules: minor typo correction
- ussl: fix module name refs and use "MicroPython port" term
- esp8266/general: add section on TLS limitations
- usocket: document that settimeout() isn't supported by all ports
- ure: add "|" (alternative) to the list of supported operators
- reference/isr_rules.rst: add tutorial on use of micropython.schedule()
travis:
- use --upgrade when pip is installing cpp-coveralls
- update build command now that stm32 Wiznet config has changed
examples:
- hwconfig_console: add .on()/.off() methods
all:
- convert mp_uint_t to mp_unary_op_t/mp_binary_op_t where appropriate
- convert remaining "mp_uint_t n_args" to "size_t n_args"
- make new ports/ sub-directory and move all ports there
- update Makefiles and others to build with new ports/ dir layout
- remove inclusion of internal py header files
- use NULL instead of "" when calling mp_raise exception helpers
README:
- update "Dependencies" section
- add explicit section on contributing
- add gcc and arm-none-eabi-newlib to list of required components
.gitattributes:
- remove obsolete entries for stmhal/hal, stmhal/cmsis
- add entries for files that will move to ports/ dir
Describe that the only portable way to deal with addresses is by using
getaddrinfo(). Describe that some ports may support tuple addresses using
"socket" module (vs "usocket" of native MicroPython).
This clarifies return values and the handling of invalid (e.g. newline)
characters.
Encoding conforms to RFC 3548, but decoding does not, as it ignores invalid
characters in base64 input. Instead, it conforms to MIME handling of base64
(RFC 2045).
Note that CPython doesn't document handling of invalid characters in
a2b_base64() docs:
https://docs.python.org/3/library/binascii.html#binascii.a2b_base64 , so
we specify it more explicitly than it, based on CPython's actual behavior
(with which MicroPython now compliant).
The old intro talked about "differences", but there were hardly any
sections describing differences, mostly MicroPython specific features.
On the other hand, we now have real "differences" chapter, though it's
mostly concerned with stdlib differences.
So, try to avoid confusion by changing wording and linking to the other
chapters and contrasting them with what is described in "MicroPython
language".
Fixes for stmhal USB mass storage, lwIP bindings and VFS regressions
This release provides an important fix for the USB mass storage device in
the stmhal port by implementing the SCSI SYNCHRONIZE_CACHE command, which
is now require by some Operating Systems. There are also fixes for the
lwIP bindings to improve non-blocking sockets and error codes. The VFS has
some regressions fixed including the ability to statvfs the root.
All changes are listed below.
py core:
- modbuiltins: add core-provided version of input() function
- objstr: catch case of negative "maxsplit" arg to str.rsplit()
- persistentcode: allow to compile with complex numbers disabled
- objstr: allow to compile with obj-repr D, and unicode disabled
- modsys: allow to compile with obj-repr D and PY_ATTRTUPLE disabled
- provide mp_decode_uint_skip() to help reduce stack usage
- makeqstrdefs.py: make script run correctly with Python 2.6
- objstringio: if created from immutable object, follow copy on write policy
extmod:
- modlwip: connect: for non-blocking mode, return EINPROGRESS
- modlwip: fix error codes for duplicate calls to connect()
- modlwip: accept: fix error code for non-blocking mode
- vfs: allow to statvfs the root directory
- vfs: allow "buffering" and "encoding" args to VFS's open()
- modframebuf: fix signed/unsigned comparison pendantic warning
lib:
- libm: use isfinite instead of finitef, for C99 compatibility
- utils/interrupt_char: remove support for KBD_EXCEPTION disabled
tests:
- basics/string_rsplit: add tests for negative "maxsplit" argument
- float: convert "sys.exit()" to "raise SystemExit"
- float/builtin_float_minmax: PEP8 fixes
- basics: convert "sys.exit()" to "raise SystemExit"
- convert remaining "sys.exit()" to "raise SystemExit"
unix port:
- convert to use core-provided version of built-in import()
- Makefile: replace references to make with $(MAKE)
windows port:
- convert to use core-provided version of built-in import()
qemu-arm port:
- Makefile: adjust object-file lists to get correct dependencies
- enable micropython.mem_*() functions to allow more tests
stmhal port:
- boards: enable DAC for NUCLEO_F767ZI board
- add support for NUCLEO_F446RE board
- pass USB handler as parameter to allow more than one USB handler
- usb: use local USB handler variable in Start-of-Frame handler
- usb: make state for USB device private to top-level USB driver
- usbdev: for MSC implement SCSI SYNCHRONIZE_CACHE command
- convert from using stmhal's input() to core provided version
cc3200 port:
- convert from using stmhal's input() to core provided version
teensy port:
- convert from using stmhal's input() to core provided version
esp8266 port:
- Makefile: replace references to make with $(MAKE)
- Makefile: add clean-modules target
- convert from using stmhal's input() to core provided version
zephyr port:
- modusocket: getaddrinfo: Fix mp_obj_len() usage
- define MICROPY_PY_SYS_PLATFORM (to "zephyr")
- machine_pin: use native Zephyr types for Zephyr API calls
docs:
- machine.Pin: remove out_value() method
- machine.Pin: add on() and off() methods
- esp8266: consistently replace Pin.high/low methods with .on/off
- esp8266/quickref: polish Pin.on()/off() examples
- network: move confusingly-named cc3200 Server class to its reference
- uos: deconditionalize, remove minor port-specific details
- uos: move cc3200 port legacy VFS mounting functions to its ref doc
- machine: sort machine classes in logical order, not alphabetically
- network: first step to describe standard network class interface
examples:
- embedding: use core-provided KeyboardInterrupt object
This adds description of implied AbstractNIC base class, which should be
"subclasses" and implemented by a particular network device class.
This is just an initial step in that direction, the API and description
will be elabotated further.
The list starts with the simplest functionality - GPIO, proceeds to
communication interfaces (UART, SPI, I2C), the to time(r) related
things, then everything else.
For a couple of ports, there was information which directory is set
as current after boot. This information doesn't belong to "uos" module,
and is moved to boards' references (which actually already contained
information on which directory is chosen for boot, even if without
explicit mentioning that it becomes current directory, which is now
done).
This method isn't implemented in any port. It seemed to have originated
in cc3200 port, but actually never was implemented there either. In
general case, it's impossible to implement this method (for example, for
a perfect GPO, which has only output latch without any feedback look
into a CPU).
Both aren't part of generic Hardware API: It's impossible to implement
.id() method in a generic case (e.g., when Pin is instantiated by the
underlying OS/RTOS). .board attribute is an obvious space hog which
instead can be implemented on Python level if needed.
MONO_xxx is much easier to read if you're not familiar with the code.
MVLSB is deprecated but kept for backwards compatibility, for the time
being.
This patch also updates the associated docs and tests.
* Fix mis-spelling of `ticks_add` in code examples.
* Be consistent about parentheses after function names.
* Be consistent about formatting of function, variable and constant names.
* Be consistent about spaces and punctuation.
* Fix some language errors (missing or wrong words, wrong word order).
* Keep line length under 90 chars.
Signed-off-by: Christopher Arndt <chris@chrisarndt.de>
MicroPython guarantees '/' to be a path separator, so extra constant taking
precious ROM space are not needed. MicroPython never had such constant, only
one vendor port had it (now unmaintained).
This new function controls what happens on a hard-fault:
- debugging disabled: board will do a reset
- debugging enabled: board will print registers and stack and flash LEDs
The default is disabled, ie to do a reset. This is different to previous
behaviour which flashed the LEDs and waited indefinitely.
machine.time_pulse_us() is intended to provide very fine timing, including
while working with signal bursts, where each transition is tracked in row.
Throwing and handling an exception may take too much time and "signal loss".
So instead, in case of a timeout, just return negative value. Cases of
timeout while waiting for initial signal stabilization, and during actual
timing, are recognized.
The documentation is updated accordingly, and rewritten somewhat to clarify
the function behavior.
