This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
This allows calls to `allocate_memory()` while the VM is running, it will then allocate from the GC heap (unless there is a suitable hole among the supervisor allocations), and when the VM exits and the GC heap is freed, the allocation will be moved to the bottom of the former GC heap and transformed into a proper supervisor allocation. Existing movable allocations will also be moved to defragment the supervisor heap and ensure that the next VM run gets as much memory as possible for the GC heap.
By itself this breaks terminalio because it violates the assumption that supervisor_display_move_memory() still has access to an undisturbed heap to copy the tilegrid from. It will work in many cases, but if you're unlucky you will get garbled terminal contents after exiting from the vm run that created the display. This will be fixed in the following commit, which is separate to simplify review.
The issue was that a time.sleep() would set the RTC wake up
further into the future even if we wanted to tick every ms. Ticking
every ms is used to time the autoreload delay and without it,
autoreload doesn't work.
Fixes#3528
Not all boards have external flash or other components that make them
require 2.7V -- sometimes we can get considerably longer battery life
by decreasing this requirement.
In particular, pewpew10 and pewpew_m4 are powered directly from
battery, with no LDO, and should work fine down to 1.6V.
This introduces the new macro SAM_D5X_E5X. This is mostly the same
as SAMD51 before, except in a few places where a special case for
SAME54 is required
I noticed that this code was referring to samd-specific functionality,
and isn't enabled except in one samd board (pewpew10). Move it.
There is incomplte support for _pew in mimxrt10xx which then caused build
errors; adding a #if guard to check for _pew being enabled fixes it.
The _pew module is not likely to be important on mimxrt but I'll leave the
choice to remove it to someone else.
* Fixes safe mode on the SAMD51. The "preserved" value was being
clobbered by the bootloader.
* Fixes auto-reload loop when in safe mode.
* Fixes reading Group children with [].
* Check that a TileGrid actually moves before queueing a refresh.
This creates a common safe mode mechanic that ports can share.
As a result, the nRF52 now has safe mode support as well.
The common safe mode adds a 700ms delay at startup where a reset
during that window will cause a reset into safe mode. This window
is designated by a yellow status pixel and flashing the single led
three times.
A couple NeoPixel fixes are included for the nRF52 as well.
Fixes#1034. Fixes#990. Fixes#615.
The backtrace cannot be given because it relies on the validity
of the qstr data structures on the heap which may have been
corrupted.
In fact, it still can crash hard when the bytecode itself is
overwritten. To fix, we'd need a way to skip gathering the
backtrace completely.
This also increases the default stack size on M4s so it can
accomodate the stack needed by ASF4s nvm API.
This started while adding USB MIDI support (and descriptor support is
in this change.) When seeing that I'd have to implement the MIDI class
logic twice, once for atmel-samd and once for nrf, I decided to refactor
the USB stack so its shared across ports. This has led to a number of
changes that remove items from the ports folder and move them into
supervisor.
Furthermore, we had external SPI flash support for nrf pending so I
factored out the connection between the usb stack and the flash API as
well. This PR also includes the QSPI support for nRF.
This reduces the popping sound on initial playback of an audio
sample.
The M4 DAC has a pop on startup that cannot be prevented. It also
does not allow readback so current values of the DAC are ignored.
Fixes#1090
It's designed to minimize RAM footprint by using Sprites to
represent objects on the screen. The object model also facilitates
partial screen updating which reduces the bandwidth needed to display.
This is all handled in C. Python simply manipulates the objects with
the ability to synchronize to frame timing.
