Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx
to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI
and NSS. This makes it the same as how I2C is configured.
This is refactoring to enable support for the two USB PHYs available on
some STM32F4 processors to be used at the same time. The F405/7 & F429
have two USB PHYs, others such as the F411 only have one PHY.
This has been tested separately on a pyb10 (USB_FS PHY) and F429DISC
(USB_HS PHY) to be able to invoke a REPL/USB. I have modified a PYBV10
to support two PHYs.
The long term objective is to support a 2nd USB PHY to be brought up as a
USB HOST, and possibly a single USB PHY to be OTG.
This is a hack to free up TIM3 so that it can be used by the user.
Instead we use the PVD irq to call the USB VCP polling function, and
trigger it from SysTick (so SysTick itself does not do any processing).
The feature is enabled for pyboard lite only, since it lacks timers.
The STMCube examples define both USE_USB_HS and USE_USB_HS_IN_FS when they
use the HS in FS mode.
The STM32F401 doesn't have a USB_HS at all, so the USB_OTG_HS instance
doesn't even exist.
If RTC is already running at boot then it's left alone. Otherwise, RTC is
started at boot but startup function returns straight away. RTC startup
is then finished the first time it is used. Fallback to LSI if LSE fails
to start in a certain time.
Also included:
MICROPY_HW_CLK_LAST_FREQ
hold pyb.freq() parameters in RTC backup reg
MICROPY_HW_RTC_USE_US
option to present datetime sub-seconds in microseconds
MICROPY_HW_RTC_USE_CALOUT
option to enable RTC calibration output
CLK_LAST_FREQ and RTC_USE_CALOUT are enabled for PYBv1.0.
py/mphal.h contains declarations for generic mp_hal_XXX functions, such
as stdio and delay/ticks, which ports should provide definitions for. A
port will also provide mphalport.h with further HAL declarations.
USB serial is now working for F7.
Internal file storage is now working for F7. The flash is laid out a bit
differently to the F4 - 4 x 32K, 1 x 128K with the rest 256K, so the
internal storage is 96K.
Added more pind definitions for STM32F7DISC board. Made USART1 be the
default HWUART repl. The STLINK usb connector also looks like a USB
serial port which is attached to USART1 on the STM32F7DISC.
To build:
make BOARD=ESPRUINO_PICO
To deploy: short the BOOT0/BTN contact on the back of the board (eg by
drawing over it with a graphite pencil), then hold down BTN while
inserting the board into the USB port. The board should then enter DFU
mode, and the firmware can be downloaded using:
make BOARD=ESPRUINO_PICO deploy
Each board now needs an mpconfigboard.mk file which defines AF_FILE and
LD_FILE.
Also moved stm32f405.ld to boards/ directory to keep things organised.
This config option is for the USB OTG pin, pin A10. This is used on
some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it
shouldn't be used for OTG ID (actually PA10 is multiplexed on this
board, but defaults to LED(2)).
Partially addresses issue #1059.
Since all currently supported boards use pin A9 for this function, the
value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used,
just the fact that it is defined.
Addresses issue #1048.
TIM2_CH1_ETR is really bundling 2 functions to the same pin:
TIM2_CH1 (where its used as a channel)
TIM2_ETR (where iss used as an external trigger).
I fixed most of these a while back, but it looks like I missed this one.
Pulled in and modified work done by mux/iabdalkader on cc3k driver, from
iabdalkader-cc3k-update branch. That branch was terribly messy and had
too many conflicts to merge neatly.
Converts generted pins to use qstrs instead of string pointers.
This patch also adds the following functions:
pyb.Pin.names()
pyb.Pin.af_list()
pyb.Pin.gpio()
dir(pyb.Pin.board) and dir(pyb.Pin.cpu) also produce useful results.
pyb.Pin now takes kw args.
pyb.Pin.__str__ now prints more useful information about the pin
configuration.
I found the following functions in my boot.py to be useful:
```python
def pins():
for pin_name in dir(pyb.Pin.board):
pin = pyb.Pin(pin_name)
print('{:10s} {:s}'.format(pin_name, str(pin)))
def af():
for pin_name in dir(pyb.Pin.board):
pin = pyb.Pin(pin_name)
print('{:10s} {:s}'.format(pin_name, str(pin.af_list())))
```
This patch updates ST's HAL to the latest version, V1.3.0, dated 19 June
2014. Files were copied verbatim from the ST package. Only change was
to suppress compiler warning of unused variables in 4 places.
A lot of the changes from ST are cosmetic: comments and white space.
Some small code changes here and there, and addition of F411 header.
Main code change is how SysTick interrupt is set: it now has a
configuration variable to set the priority, so we no longer need to work
around this (originall in system_stm32f4xx.c).
This renames MICROPY_HW_HAS_WLAN to MICROPY_HW_ENABLE_CC3K (since it's a
driver, not a board feature) and wraps all CC3000 code in this #if.
It's disabled for all boards.
It's not enabled by default because it doesn't fully work. It can
connect to an AP, get an IP address and do a host-lookup, but not yet do
send or recv on a socket.
This is an attempt to clean up the Micro Python API on the pyboard.
Gpio functionality is now in the Pin object, which seems more natural.
Constants for MODE and PULL are now in pyb.Pin. Names of some
classes have been adjusted to conform to CamelCase. Other
miscellaneous changes and clean up here and there.
All board config macros now begin with MICROPY_HW_.
Renamed PYBv10 to PYBV10, since macros should be all uppercase.
Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD
detect pin can be easily configured.
Added support for the ADC channels and mappings to make_pins.py
I'm not sure if the hal properly deals with the channel 16/18 differences
between the 40x and 42x. It seems to deal with it partially. This particular
aspect will need testing on a 42x or 43x.
