The expectations of displayio.Display and frambufferio.FramebufferDisplay
are different when it comes to rotation.
In displayio.Display, if you call core_construct with a WxH = 64x32
and rotation=90, you get something that is 32 pixels wide and 64 pixels
tall in the LCD's coordinate system.
This is fine, as the existing definitions were written to work like this.
With framebuffer displays, however, the underlying framebuffer (such as
RGBMatrix) says "I am WxH pixels wide in my coordinate system" and the
constructor is given a rotation; when the rotation indicates a transpose
that means "exchange rows and columns, so that to the Groups displayed
on it, there is an effectively HxW pixel region for use".
Happily, we already have a set_rotation method. Thus (modulo the time
spent debugging things anyway:) the fix is simple: Always request no
rotation from core_construct, then immediately fix up the rotation
to match what was requested.
Testing performed: 32x16 RGBMatrix on Metro M4 Express (but using
the Airlift firmware, as this is the configuration the error was reported
on):
* initially construct display at 0, 90, 180, 270 degrees
* later change angle to 0, 90, 180, 270 degrees
* no garbled display
* no safe mode crashes
e.g., allocating a 192x32x6bpp matrix would be enough to trigger this
reliably on a Metro M4 Express using the "memory hogging" layout.
Allocating 64x32x6bpp could trigger it, but somewhat unreliably.
There are several things going on here:
* we make the failing call with interrupts off
* we were throwing an exception with interrupts off
* protomatter failed badly in _PM_free when it was partially-initialized
Incorporate the fix from protomatter, switch to a non-throwing malloc
variant, and ensure that interrupts get turned back on.
This decreases the quality of the MemoryError (it cannot report the size
of the failed allocation) but allows CircuitPython to survive, rather
than faulting.
this flips the bottom-right style to top-left which is at least
kind of normal. A 2x2 square at (0,0) would be defined like
(0,0), (3,0), (3,3), (0,3)
Which seems kind of surprising but at least less bonkers than
that square being defined at (1,1), which is the current behavior.
The getter for vectorio.Polygon#points was not updated with the data type change of the stored points list.
This moves the implementation to shared_module and updates the data type to reflect the actual state.
Before this, the mp3 file would be read into the in-memory buffer
only when new samples were actually needed. This meant that the time
to read mp3 content always counted against the ~22ms audio buffer length.
Now, when there's at least 1 full disk block of free space in the input
buffer, we can request that the buffer be filled _after_ returning from
audiomp3_mp3file_get_buffer and actually filling the DMA pointers. In
this way, the time taken for reading MP3 data from flash/SD is less
likely to cause an underrun of audio DMA.
The existing calls to fill the inbuf remain, but in most cases during
streaming these become no-ops because the buffer will be over half full.
Testing performed: That a card is successfully mounted on Pygamer with
the built in SD card slot
This module is enabled for most FULL_BUILD boards, but is disabled for
samd21 ("M0"), litex, and pca10100 for various reasons.
I noticed that this code was referring to samd-specific functionality,
and isn't enabled except in one samd board (pewpew10). Move it.
There is incomplte support for _pew in mimxrt10xx which then caused build
errors; adding a #if guard to check for _pew being enabled fixes it.
The _pew module is not likely to be important on mimxrt but I'll leave the
choice to remove it to someone else.
There were two main problems
- word_buffer was being filled as though with unsigned samples,
but during mixing all samples are kept in signed mode
- If the first buffer was stopped, the voices_active flag got set
anyway, even though the output buffer wasn't initialized yet,
so the samples were mixed with indeterminate data
We also cover the case where no buffer was playing, and ensure
the output buffer is filled.
This now works much better. Tested on neotrellis m4 playing back
4 mp3 streams at a time in signed-16, 22050Hz
root
Kevin Matocha
DavePutz
Scott Shawcroft
Scott Shawcroft
Jeff Epler
Jeff Epler
Dan Halbert
Yihui Xiong
Jeff Epler
Margaret Matocha
Roy Hooper
Kenny
hierophect
Diego Elio Pettenò