09d1c846c4
Set heap size to 0 when heap allocation fails
2022-07-13 13:53:22 -05:00
c1b6c367ff
esp32 can allocate 88kB successfully
2022-07-13 13:53:08 -05:00
13be10ef14
rename function to avoid confusion
2022-07-13 13:28:51 -05:00
5c6ee20ca5
on esp32 need to initialize nvs before starting wifi
...
Also, change error handling so that the esp-idf error number
is shown in the traceback in the case of an error.
This allows scanning & connecting to work. I didn't try requests yet.
2022-07-13 11:57:38 -05:00
f620c2901c
Set a small but working heap size for esp32 without psram
2022-07-13 11:10:00 -05:00
ea52ca66dc
Disable SPIRAM bankswitch on esp32
...
We don't use this facility, which was reserving the last 256kiB of
psram.
2022-07-13 10:56:58 -05:00
953f44b46e
Fix spiram limit calculation on esp32
...
esp32 places the psram start at SOC_EXTRAM_DATA_LOW and it can extend
up to SOC_EXTRAM_DATA_SIZE. This is different than esp32-s2 and later,
which place the end at EXTRAM_DATA_HIGH and the limitation of
SOC_EXTRAM_DATA_SIZE was not previously identified as important.
Additionally, the esp32 has a reserved area within himem which was
not being accounted for.
With this change, the Feather ESP32 V2 feather can be used via thonny,
and the other "quick memory corruption tests" I was performing
also all succeed instead of failing.
Before this change, the incorrect address being used for spiram was
0x3fa00000..0x3fc00000 (2MiB). Now, it's 0x3f800000..0x3f9c0000 (1.75MiB)
due to the reserved area and the changed start address.
This is intended to be a no-effect change for other espressif chips besides
original esp32.
2022-07-13 10:52:15 -05:00
afbaa2eb6c
decode_backtrace: Show even more information
...
addr2line can show information about how functions were inlined,
including function names
Typical new output:
```
0x400dec57: mp_obj_get_type at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:68
(inlined by) mp_obj_print_helper at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:133
(inlined by) mp_obj_print_helper at /home/jepler/src/circuitpython/ports/espressif/../../py/obj.c:114
0x400e1a25: fun_builtin_1_call at /home/jepler/src/circuitpython/ports/espressif/../../py/objfun.c:75
0x400dd016: mp_call_function_n_kw at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:665
0x400eac99: mp_execute_bytecode at /home/jepler/src/circuitpython/ports/espressif/../../py/vm.c:936
0x400e1ae9: fun_bc_call at /home/jepler/src/circuitpython/ports/espressif/../../py/objfun.c:297 (discriminator 4)
0x400dd016: mp_call_function_n_kw at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:665
0x400dd03a: mp_call_function_0 at /home/jepler/src/circuitpython/ports/espressif/../../py/runtime.c:638
0x40117c03: parse_compile_execute at /home/jepler/src/circuitpython/ports/espressif/../../shared/runtime/pyexec.c:146
0x4011800d: pyexec_friendly_repl at /home/jepler/src/circuitpython/ports/espressif/../../shared/runtime/pyexec.c:734
0x400eeded: run_repl at /home/jepler/src/circuitpython/ports/espressif/../../main.c:823
(inlined by) main at /home/jepler/src/circuitpython/ports/espressif/../../main.c:922
0x400ef5e3: app_main at /home/jepler/src/circuitpython/ports/espressif/supervisor/port.c:410
0x401bb461: main_task at /home/jepler/src/circuitpython/ports/espressif/build-adafruit_feather_esp32_v2/esp-idf/../../esp-idf/components/freertos/port/port_common.c:141
```
2022-07-12 16:28:33 -05:00
23bbb19138
Merge remote-tracking branch 'adafruit/main' into websocket_serial
2022-07-12 13:15:38 -07:00
c56f363a23
Merge pull request #6572 from todbot/wifi-tx-power-float
...
Fix #6559
2022-07-11 13:08:11 -07:00
08b4a64bd2
Update the PID
2022-07-11 08:39:10 -07:00
a658007673
Update ports/espressif/common-hal/wifi/Radio.c
...
Co-authored-by: Dan Halbert <halbert@halwitz.org>
2022-07-09 22:17:26 -07:00
22e061ba35
Update ports/espressif/common-hal/wifi/Radio.c
...
Co-authored-by: Dan Halbert <halbert@halwitz.org>
2022-07-09 22:17:18 -07:00
98692150ac
Update ports/espressif/common-hal/wifi/Radio.c
...
Co-authored-by: Dan Halbert <halbert@halwitz.org>
2022-07-09 22:17:12 -07:00
f464ec3047
Update ports/espressif/common-hal/wifi/Radio.c
...
Co-authored-by: Dan Halbert <halbert@halwitz.org>
2022-07-09 22:17:02 -07:00
bc14b7ad47
Fix the display on the esp box lite
2022-07-08 15:40:59 -07:00
2c7ad7a39f
make translate and pre-commit formatting fixes
2022-07-08 16:53:53 -04:00
c316b950c7
merge from adafruit/main
2022-07-08 15:42:19 -04:00
d869b441f4
further ESP32 sdkconfig fixes; add CIRCUITPY_STATUS_BAR
2022-07-08 15:27:00 -04:00
76e32dcf93
remove need for CIRCUITPY_ESP_PSRAM
2022-07-08 14:54:55 -04:00
afbf4de071
Uncomment or remove debugging changes
2022-07-08 12:53:25 -04:00
c3cd32e773
CPU freq to 240 MHz, redo sdkconfigs
2022-07-08 10:50:00 -04:00
75208573f4
tweak sdkconfig; add temp logging to mp_make_function_from_raw_code
2022-07-08 09:53:29 -04:00
d3e1d1b104
Fix #6559
2022-07-07 19:42:11 -07:00
4e88d795e1
Thonny causing crash emitglue.c:199:
2022-07-06 23:01:19 -04:00
d83720f659
Tweak display init
2022-07-05 17:02:52 -07:00
cd77517b2f
Add build for ESP32-S3 Box Lite
2022-07-05 16:35:42 -07:00
07b2697ae3
WIP websocket to serial
2022-07-01 16:57:10 -07:00
c3cf9ba9ce
remove wifi max from sdkconfig
2022-07-01 14:50:47 -07:00
aaeda97818
update PHY section, correct name
2022-07-01 14:50:47 -07:00
aa53d36934
setting CONFIG_ESP32_PHY_MAX_WIFI_TX_POWER to 8.5
2022-07-01 14:50:47 -07:00
7e367eeb58
Update "D" mappings
2022-07-01 14:50:47 -07:00
d4b26daf1b
correct creator and creation IDs
2022-07-01 14:50:47 -07:00
6c7faf0eba
Change USB VID & PID to Creator and Creation IDs
2022-07-01 14:50:47 -07:00
3253ae2503
tested and corrected several pins
2022-07-01 14:50:47 -07:00
f10fa566aa
REPL works. Based on QTPYC3.
2022-07-01 14:50:47 -07:00
a3070f6c2a
Changes to Pin Mappings
2022-07-01 14:50:46 -07:00
b37236f83f
C3 does not have PSRAM
2022-07-01 14:50:46 -07:00
af629ab180
Add assumed PID value
2022-07-01 14:50:46 -07:00
c1e6003d26
remove comment that breaks {ID Checker
2022-07-01 14:50:46 -07:00
9bae8549c5
add UART RX TX to mpconfigboard
2022-07-01 14:50:46 -07:00
6763b7b968
add A5
2022-07-01 14:50:46 -07:00
bcf27e146b
fix build break and add io 20/21
2022-07-01 14:50:46 -07:00
dc1c86738a
Initial pin mapping pass
2022-07-01 14:50:46 -07:00
fd4695d0f2
Gettting started with pin mapping.
2022-07-01 14:50:46 -07:00
8814ee03f1
Merge pull request #6542 from todbot/wifi-tx-power
...
Add wifi.radio.tx_power
2022-07-01 14:09:08 -04:00
7589e53fea
WIP websocket accept and hashlib
2022-07-01 10:18:33 -07:00
8bb369cac5
refactor debug UART to console UART; get working on ESP32
2022-06-30 23:16:46 -04:00
187f156ac7
Merge pull request #6534 from tannewt/esp_wdt_safe_mode
...
Safe mode when ESP interrupt watchdog fires
2022-06-30 22:56:35 -04:00
698d563dcf
adust wifi.radio.tx_power to be x4 (in db) as mentioned in #6540
2022-06-30 15:33:03 -07:00
2a563cc8ba
first cut at wifi.radio.tx_power
2022-06-30 15:10:16 -07:00
b0efd130c9
ESP32 REPL working through debug UART
2022-06-29 23:19:36 -04:00
3be3e89d82
Merge branch 'main' into cp_webserver
2022-06-29 14:01:32 -07:00
c3a149c14a
Merge pull request #6533 from tannewt/fix_connect_crash
...
Fix auto-wifi created crash
2022-06-29 16:51:33 -04:00
d42c811fb9
Safe mode when ESP interrupt watchdog fires
...
This makes us enter safe mode when sleep on the S3 fails. The
task watchdog is used for the user watchdog.
2022-06-29 12:31:18 -07:00
8dc8265275
Fix auto-wifi created crash
...
The wifi event_handler runs on the other core so we need to be
careful when calling into CP APIs.
Fixes #6503
2022-06-29 11:53:10 -07:00
1f065a313c
Update with startup fix instead of revert
2022-06-29 11:12:29 -07:00
780c4963cb
wip; change never-ever reset pin mechanism
2022-06-28 23:06:49 -04:00
a8bb3eb557
Update to newer 4.4 branch
2022-06-28 15:38:55 -07:00
ca64950503
wip fixes
2022-06-28 18:32:08 -04:00
41039445c9
Clean up and add docs
2022-06-27 13:39:09 -07:00
7acc5ebeb9
Add logo for going to home. Fix origin check
2022-06-27 13:39:09 -07:00
3cd05291d0
Static files + welcome page
2022-06-27 13:39:09 -07:00
7543dd9af0
CORS works and autoreload too
2022-06-27 13:39:08 -07:00
92593aa7a1
Fix bind, remove hard coded ip
2022-06-27 13:34:13 -07:00
4f0a7aedfd
WIP adding devices.json and auth
2022-06-27 13:34:13 -07:00
32478345f8
more tweaks
2022-06-27 13:34:13 -07:00
0882cbf823
web server kinda works
2022-06-27 13:34:13 -07:00
61d0f7947b
WIP doesn't flush response before closing
2022-06-27 13:34:13 -07:00
301f3e0456
Start of web server
2022-06-27 13:34:13 -07:00
55784c93de
wip; compiles
2022-06-26 21:22:22 -04:00
02069eb0b5
wip
2022-06-23 15:59:06 -04:00
ba72287db4
Implement default ports to IOTS2
2022-06-22 07:24:27 +02:00
0c418e98b1
Merge remote-tracking branch 'adafruit/main' into auto_wifi
2022-06-13 15:44:43 -07:00
dc794f91c0
Speed up auto-wifi with wrong password
...
This adds basic timeout support to connect by preventing subsequent
retries if over time. The first connect may still take more than
the timeout.
2022-06-13 15:38:19 -07:00
b191075ab8
Better length checks
2022-06-13 09:18:42 -07:00
39b8c2c94e
Merge pull request #6453 from KurtE/ESP32_UART
...
ESP32 USE uart_param_config
2022-06-13 08:56:32 -07:00
6446010753
Wi-Fi autoconnect and title bar status
...
This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
2022-06-09 14:55:54 -07:00
2baf476530
Merge pull request #6463 from adafruit/7.3.x
...
Catch main up to 7.3.x
2022-06-06 11:58:05 -07:00
6b09f99eaa
Add back ULAB
2022-06-06 10:35:37 -07:00
80ae14202a
Merge pull request #6416 from FoamyGuy/display_brightness_pwm
...
display brightness pwm 500hz frequency
2022-06-05 23:52:42 -04:00
ac282b2a73
Merge pull request #6440 from tannewt/translate_header
...
Switch translate() to the header file
2022-06-05 23:50:47 -04:00
c149bbdcfc
Merge pull request #6447 from SimonVail/main
...
Add files via upload
2022-06-05 17:11:44 -04:00
db6d506b15
Merge pull request #6456 from dhalbert/adafruit_feather_esp32s3_4mbflash_2mbpsram
...
add adafruit_feather_esp32s3_4mbflash_2mbpsram
2022-06-05 12:31:20 -04:00
67de89861e
new argument for feather s3 tft display init
2022-06-04 11:36:45 -05:00
260994d16e
Merge branch 'main' into display_brightness_pwm
2022-06-04 11:32:15 -05:00
cbff9dd8e3
add new argument for all boards with built-in display
2022-06-04 11:08:20 -05:00
d1cdb72020
Update ports/espressif/boards/adafruit_feather_esp32s3_4mbflash_2mbpsram/mpconfigboard.h
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2022-06-03 18:21:20 -04:00
be67067809
Merge remote-tracking branch 'adafruit/main' into translate_header
2022-06-03 15:18:18 -07:00
fdb133bbe8
add adafruit_feather_esp32s3_4mbflash_2mbpsram
2022-06-02 21:09:37 -04:00
27fb96e6b0
Remove trailing whitespace
2022-06-01 21:35:01 -04:00
40e890323b
Add DNS optional to set IP
2022-06-01 20:13:51 -05:00
14ab3c7375
ESP32 USE uart_param_config
...
Use this function instead of several individual configuration functions
to configure such things as Baud rate, transfer size, stop bits,
parity...
This function also resets both the RX and TX Hardware Fifo
reset functions are called to setup the hardware.
2022-06-01 17:09:44 -07:00
4f6d4e2284
Doc fix and add set for DNS
2022-05-31 22:13:18 -05:00
b2344bcde2
Update pins.c
2022-05-30 11:52:29 -04:00
f36dbb386b
Add files via upload
2022-05-30 11:47:51 -04:00
90fe20a153
Adding manual IP address set
2022-05-27 15:33:54 -05:00
9d10a3da66
Conditionalize LTO
2022-05-27 12:59:54 -07:00
c676253834
Switch translate() to the header file
...
This allows the compile stage to optimize most of the translate()
function away and saves a ton of space (~40k on ESP). *However*, it
requires us to wait for the qstr output before we compile the rest
of our .o files. (Only qstr.o used to wait.)
This isn't as good as the current setup with LTO though. Trinket M0
loses <1k with this setup.
So, we should probably conditionalize this along with LTO.
2022-05-27 10:33:53 -07:00
b143314b22
Espressif: fix allocation of multiple Incremental Encoders
2022-05-24 22:37:24 -04:00
99d7d0d8bb
Disable ulab for ESP32-S3 TFT
2022-05-24 14:59:34 -04:00
e22de975b3
try just bitbangio remove
2022-05-24 11:46:03 -04:00
9439ce04bd
try to remove some space?
2022-05-24 11:28:55 -04:00
bb4beb3fab
add esp32s3 tft
2022-05-23 23:57:35 -04:00
64df933a83
Merge pull request #6422 from dahanzimin/main
...
Repair mixgo_ce frozen lib to frozen/
2022-05-23 15:00:42 -04:00
6454c5895b
Repair import and stock in under the frozen / directory
2022-05-23 11:19:11 +08:00
6f4f7e089e
Merge pull request #6383 from dahanzimin/main
...
Add MixGo CE board
2022-05-22 08:47:53 -04:00
e5a5ffb9b0
Update board.c
2022-05-22 11:37:39 +08:00
37e376631a
Fix format issues
2022-05-22 11:22:58 +08:00
b62799a798
Add mixgo_ ce_ Serial function, repair sdkconfig
2022-05-22 10:42:56 +08:00
3e47d24fb9
Update submodule and create tag
2022-05-21 10:52:14 +08:00
f63b26c534
address jepler's comments and further squeezes
2022-05-20 10:10:55 -04:00
4356a12504
Update mpconfigboard.mk
2022-05-20 10:55:23 +08:00
73f2621cda
Repair No newline at end of file
2022-05-20 10:38:14 +08:00
525262cd9a
Merge branch 'main' into main
2022-05-20 10:04:02 +08:00
e3896be345
Modify mixgoce_ Lib is a submodule
2022-05-20 09:46:55 +08:00
a01dec1df9
message consolidation and more use of validators
2022-05-19 15:38:37 -04:00
d2d08fc944
fix SPI pin names qtpy esp32s3
2022-05-13 16:48:13 -07:00
64ca3aa359
Merge pull request #6387 from SimonVail/main
...
Lilygo TTGO T-OI Plus ESP32C3
2022-05-13 18:31:50 -04:00
1f0bdad083
Update ports/espressif/boards/lilygo_ttgo_t-oi-plus/mpconfigboard.mk
...
Co-authored-by: Scott Shawcroft <scott@tannewt.org>
2022-05-13 15:02:26 -04:00
3e85cfe26b
Fix ESP and HCI build
2022-05-12 15:23:26 -07:00
ef4d298ca8
Update pins.c
2022-05-12 17:49:48 -04:00
0d92b0a155
Update board.c
2022-05-12 17:46:49 -04:00
b1935975a2
Update board.c
2022-05-12 17:27:48 -04:00
269d51d023
Add two stage reset for BLE
...
This lets the BLE stack run through the wait period after a VM run
when it may be waiting for more writes due to an auto-reload.
User BLE functionality will have their events stopped. Scanning and
advertising is also stopped.
2022-05-12 13:20:44 -07:00
c5db1280ee
Update mpconfigboard.mk
2022-05-12 13:21:58 -04:00
6bdd128fb3
Add files via upload
2022-05-12 13:18:39 -04:00
f69a293795
Create sdkconfig
2022-05-12 13:18:17 -04:00
a4f505dcab
Delete ports/espressif/boards/Lilygo-T-oi-Plus-ESP32C3 directory
2022-05-12 13:17:17 -04:00
0b586e9c94
Update board.c
2022-05-12 12:43:52 -04:00
6fe728a9d2
Update ports/espressif/boards/Lilygo-T-oi-Plus-ESP32C3/pins.c
...
Co-authored-by: Neradoc <Neradoc@users.noreply.github.com>
2022-05-12 11:57:59 -04:00
6908f5a97e
Update ports/espressif/boards/Lilygo-T-oi-Plus-ESP32C3/board.c
...
Co-authored-by: Neradoc <Neradoc@users.noreply.github.com>
2022-05-12 11:57:52 -04:00
b6e6ee7505
Update ports/espressif/boards/Lilygo-T-oi-Plus-ESP32C3/mpconfigboard.mk
...
Co-authored-by: Neradoc <Neradoc@users.noreply.github.com>
2022-05-12 11:57:44 -04:00
b9ea7458ab
Add files via upload
2022-05-12 11:41:53 -04:00
35d78c135a
Create sdkconfig
2022-05-12 11:41:29 -04:00
f86ebe71b6
Delete Lilygo-T-oi-Plus-ESP32C3
2022-05-12 11:40:16 -04:00
0d1740ad27
Create Lilygo-T-oi-Plus-ESP32C3
2022-05-12 11:39:39 -04:00
d4b02e22ae
Thank you. I have applied for PID in espressif
2022-05-12 09:38:13 +08:00
b9c28742be
Added newline at the end of the file.
2022-05-11 15:30:45 +08:00
466f2a3644
Updated copyright information.
2022-05-11 15:25:32 +08:00
142ed2a024
Added Maker Feather AIoT S3.
2022-05-11 15:18:31 +08:00
d48f961d0a
Add MixGo CE board
2022-05-10 18:56:13 +08:00
8b026a2c38
apply i2c delay fix from adafruit/esp-idf
2022-05-08 09:49:18 -04:00
30904a8638
Merge pull request #6354 from dhalbert/espressif-dio-fixes
...
espressif: check properly for pull values
2022-05-05 22:44:29 -04:00
0f3eb9f46e
espressif: check properly for pull values
2022-05-04 22:51:27 -04:00
76040a9380
removed duplicate include per issue 6278
2022-05-04 14:57:37 -04:00
7e622c3ff7
mpconfigboard.h also needs neopixel tweak
2022-05-02 13:23:55 -07:00
5d4e964de0
fix qtpy_esp32s3_nopsram neopixel pins
2022-05-02 13:04:05 -07:00
e63a327107
Bound PulseIn start indexes to maxlen.
2022-04-28 02:28:34 +00:00
4eeaf41edc
test and adjust NeoPixel timings on multiple products
2022-04-25 23:12:24 -04:00
17bba7b17d
remove Adafruit_CircuitPython_BusDevice from frozen modules, it's built in now
2022-04-19 06:49:11 +02:00
c3cfbc1259
Force pin 21 high; patch; need to diagnose further
2022-04-09 22:03:16 -04:00
d5deddcaf5
Merge pull request #6207 from domdfcoding/esp32-rotaryio
...
Add espressif rotaryio divisor support.
2022-04-06 21:35:02 -04:00
f297e872d6
Account for divisor when overriding position.
2022-04-06 18:13:59 +01:00
99dc4029dc
Espressif: disable pull-up on AnalogIn creation
2022-04-06 11:33:56 -04:00
b993313ac1
Don't reset GPIO4 (used for voltage monitoring)
2022-04-05 11:30:12 -05:00
390a473dda
add board.DISPLAY since display already set up by CirPy
2022-04-01 15:08:43 -07:00
319ca8560c
Always configure the second PCNT channel.
2022-03-31 20:00:34 +01:00
ec5c9507b9
Merge pull request #6187 from prplz/espressif-uart-workflow-fixes
...
Espressif: Fix interrupts in UART workflow
2022-03-30 21:18:02 -04:00
6fd968fc12
Merge pull request #6199 from erongd/muselab-wrover-spiram-fix
...
enable SPIRAM support on muselab nanoESP32S2 board
2022-03-30 21:14:59 -04:00
6d025a239e
Add espressif rotaryio divisor support.
2022-03-28 09:04:02 +01:00
f96cd7361d
Fix esp32s2 build
2022-03-27 10:09:23 +11:00
dd73182441
Merge pull request #6190 from tannewt/esp32s3_usb_devkit
...
Add ESP32-S3-USB-OTG board
2022-03-26 15:05:30 -05:00
35aa32bec0
Merge pull request #6193 from tannewt/fix_empty_mdns
...
Fix MDNS crash on S2
2022-03-26 15:05:17 -05:00
686012426d
Espressif: Fix interrupts in UART workflow
2022-03-25 16:20:04 +11:00
7ad6fa8df5
enable SPIRAM support on muselab nanoESP32S2 board
2022-03-24 16:46:13 -07:00
8642dc4aa7
Fix MDNS crash on S2
...
Fixes #6186
2022-03-23 17:17:48 -07:00
380a7087d4
Fix 3-wire SPI on ESP
...
Simplifying the checks fixed it.
Fixes #6141
2022-03-23 14:53:46 -07:00
e13d32b832
Add ESP32-S3-USB-OTG board
...
This board has both types of USB connectors, a display and buttons
to select items on the display. It also has a micro-B connector for
the UART output.
2022-03-23 14:10:26 -07:00
ee4c501936
Merge remote-tracking branch 'adafruit/main' into c3_serial_jtag
2022-03-23 12:17:02 -07:00
f5d90fc84f
Switch to port_serial_* hooks
...
This makes it easier to integrate port specific serial alongside
the common approaches.
2022-03-22 19:40:33 -07:00
110857c12e
Actually turn on serial over Serial/JTAG for QTPy
2022-03-22 11:45:47 -07:00
b8d1bb1d5d
Shrink C3 builds
2022-03-22 10:46:57 -07:00
4363361c87
Board definition clean up
...
Removes:
* AUTORESET_DELAY_MS which never did anything but was introduced
somehow.
* CIRCUITPY_BOOT_BUTTON in all but one ESP board because they all have
them. There is a default based on the strapping pins.
* BOARD_USER_SAFE_MODE_ACTION because it was all the same for boards
with boot buttons. Now the safe mode code manages the message.
2022-03-21 17:58:43 -07:00
623b6fad16
Fix nested categories in update_sdkconfig.py
...
Also, mark QTPy C3 as BIN only.
2022-03-21 17:04:19 -07:00
6dd9db31b3
Add USB to Serial/JTAG support for REPL
...
Adds Adafruit QT Py C3 board that uses it. Also revamps size
check script to work for S3 and C3 as well.
Fixes #6030
2022-03-21 14:03:57 -07:00
4465adfe01
Merge pull request #6175 from tannewt/mdns
...
Add mdns module
2022-03-21 15:55:03 -05:00
92d946fcac
Guard against NULL result
2022-03-21 10:15:46 -07:00
fdf27eee12
add feather esp32-s3 8mb flash, 0 psram
2022-03-19 23:04:20 -04:00
6f0d62d85e
Formatting and shrink build size on C3
2022-03-18 12:05:54 -07:00
e9d81c2826
Add mdns module
...
This allows for CircuitPython to resolve a .local domain and find
other devices with MDNS services.
First step for #6174
2022-03-17 18:16:16 -07:00
da92d508c2
lilygo_ttgo_t-01c3: Add creation ID
2022-03-17 19:21:34 +11:00
de168b106c
Add board lilygo_ttgo_t-01c3
2022-03-17 17:24:24 +11:00
af9f80daeb
Merge pull request #6144 from tannewt/back_to_idf4.4
...
Update ESP-IDF to fix PinAlarm
2022-03-15 17:10:42 -04:00
f13d218749
Merge pull request #6125 from tannewt/usb_host
...
Start of USB host API
2022-03-11 21:41:28 -05:00
96dd11a198
Update ESP-IDF to fix PinAlarm
...
Fixes #5973
2022-03-11 14:40:49 -08:00
862210b3fb
Merge pull request #6135 from CircuitART/main
...
merge hexky_s2 board
2022-03-11 07:48:54 -05:00
43bd2c41e0
Update pins.c
2022-03-11 13:27:08 +08:00
597430ef96
Update pins.c
2022-03-11 12:26:49 +08:00
016bc00f01
Update pins.c
...
fixed
2022-03-11 11:54:32 +08:00
c9ec5c89b6
Fix ESP32-S3 box display color order
2022-03-10 15:50:07 -08:00
4bfe9e53df
merge hexky_s2 board
...
Hello, please add support to my custom esp32-s2 board.
thanks
2022-03-10 13:27:14 +08:00
442026548f
Merge pull request #6084 from fabaff/lilygo-ttgo-esp32-s2
...
Add support for LILYGO TTGO T8 ESP32-S2-WROOM
2022-03-08 21:00:44 -05:00
0a72420dcb
Add support for LILYGO TTGO T8 ESP32-S2-WROOM
2022-03-08 20:07:37 +01:00
1b1b363515
Add support for LILYGO TTGO T8 ESP32-S2
2022-03-08 19:56:41 +01:00
1c8f671f0a
Merge pull request #6118 from pewpew-game/parallel-reset-optional
...
paralleldisplay: reset and read pins should be optional
2022-03-08 09:34:25 -05:00
bc1dade304
Espressif: Fix i2c pullup detection
2022-03-08 16:39:24 +11:00
83593a1558
Start of USB host API
...
This allows you to list and explore connected USB devices. It
only stubs out the methods to communicate to endpoints. That will
come in a follow up once TinyUSB has it. (It's in progress.)
Related to #5986
2022-03-07 18:07:25 -08:00
b5ad78715c
Update ports/espressif/common-hal/paralleldisplay/ParallelBus.h
...
Co-authored-by: Dan Halbert <halbert@halwitz.org>
2022-03-05 21:48:00 +01:00
f477848ac1
paralleldisplay: reset and read pins should be optional
...
The ``reset`` and ``read`` pins should be optional, but the espressif
code had several places where it assumed they are not, and a bug that
caused a crash on ``release_displays`` if they were made optional.
The bug was caused by the fields for storing pin numbers being set
to ``NO_PIN``, which has value of -1, while the fields have type
``uint8_t``. That set the actual value to 255, and a subsequent
comparison to ``NO_PIN`` returned false.
2022-03-05 18:54:12 +01:00
Jeff Epler
Scott Shawcroft
Melissa LeBlanc-Williams
Tod Kurt
Dan Halbert
Patrick
Dan Halbert
Neradoc
foamyguy
gamblor21
KurtE
SimonVail
lady ada
dahanzimin
大汉子民
Kong Wai Weng
billvanleeuwen424
Michael Wisslead
Dominic Davis-Foster
root
Michael Himing
Eric Rong
CircuitART
Fabian Affolter
Radomir Dopieralski
Radomir Dopieralski