In particular, this makes the L4 .isr_vector section 16K in size so it's
the same as the F4/F7 MCUs. The patch also moves the L4 filesystem to
the end of flash, which allows for 512K filesystem on the 1Mb devices
like the STM32L476DISC.
The delay_half parameter must be specified by the port to set up the
timing of the software SPI. This allows the port to adjust the timing
value to better suit its timing characteristics, as well as provide a
more accurate printing of the baudrate.
It's simpler to just default to always using software SPI if no specific
peripheral id/name is given. To use hardware SPI users must specify a
hardware peripheral id as the first parameter to the SPI constructor.
There is no need to take src_len and dest_len arguments. The case of
reading-only with a single output byte (originally src_len=1, dest_len>1)
is now handled by using the output buffer as the input buffer, and using
memset to fill the output byte into this buffer. This simplifies the
implementations of the spi_transfer protocol function.
To reset the flags we should write to the single bit only, not the entire
register (otherwise all other settings in the register are cleared).
Fixes#2457.
UART1 can be used even if the switch is enabled. The schematics for this
board make I2C1 available on PB8/PB9, even though it can also be mapped
to PB6/PB7.
See #2396 and #2427.
If a user tries to call `swint()` while interrupt is disabled the flag in
SWIER is set but the interrupt is not triggered and therefore the SWIER bit
is not cleared. When the interrupt is again enabled the next call to
`swint()` won't trigger the IRQ because a 0 to 1 transition will not occur.
The LCD interface library fails to deassert the chip select of the LCD
after an SPI transmission. Consequently using the SPI with other
peripherals disturbs the state of the LCD. This patch changes
lcd.lcd_out() to deassert CS after each transmission to the LCD.
machine.POWER_ON is renamed to machine.PWRON_RESET to match other
reset-cause constants that all end in _RESET. The cc3200 port keeps a
legacy definition of POWER_ON for backwards compatibility.
This new config option allows to control whether MicroPython uses its own
internal printf or not (if not, an external one should be linked in).
Accompanying this new option is the inclusion of lib/utils/printf.c in the
core list of source files, so that ports no longer need to include it
themselves.
This extra forward slash for the starting-point directory is unnecessary
and leads to additional slashes on Max OS X which mean that the frozen
files cannot be imported.
Fixes#2374.
This patch makes second and next calls to <socket>.close() a no-op.
It prevents GC from closing the underlying resource after user
already used <socket>.close() explicitly.
fixes#2355
It turns out that TIM1 and TIM8 have their own Capture/Compare
interrupt vector. For all of the other timers, the capture/compare
interrupt vector is the same as the update vector.
So we need to add handlers for these vectors and enable them
when using capture/compare callbacks.
During testing of this, I also found that passing a channel callback
into the channel constructor would not enable interrupts properly.
I tested using:
```
>>> pyb.Timer(1, freq=4).channel(1, pyb.Timer.OC_TOGGLE, callback=lambda t: print('.', end=''))
```
I tested the above with channels 1, 4, and 8
This type was used only for the typedef of mp_obj_t, which is now defined
by the object representation. So we can now remove this unused typedef,
to simplify the mpconfigport.h file.
Fixing Issue #2243. Main problems were:
- HAL_ADC_GetState(adcHandle) may return other bits set (not only
HAL_ADC_STATE_EOC_REG) when called - so I AND-ed it out as proposed by
mattbrejza in Issue #2243.
- ADC Pin has to be configured as GPIO_MODE_ANALOG_ADC_CONTROL not only
GPIO_MODE_ANALOG.
- Resolved ADC resolution L4 specific (Use L4 define ADC_RESOLUTION_12B).
- Changed setting of Init.EOCSelection toADC_EOC_SINGLE_CONV for L4.
- Added call to ADC_MultiModeTypeDef as this is done on a STM32Cube
generated project too.
- Clean up: Configuration of ADC is done only in ONE function not the same
is done in two functions.
Test is done on PA5 pin of STM32L4Discovery-Kit which is connected to the
DOWN button.
Thanks to mattbrejza for discovering the bug.
For example, the following code now works with a file on the SD card:
f = open('test', 'rb') # test must be 1024 bytes or more in size
f.seek(511)
f.read(513)
Also works for writing.
Fixes issue #1863.
The main thing is to change the DMA code in a way that the structure
DMA_Stream_TypeDef (which is similar to DMA_Channel_TypeDef on stm32l4)
is no longer used outside of dma.c, as this structure only exists for the
F4 series. Therefore I introduced a new structure (dma_descr_t) which
handles all DMA specific stuff for configuration. Further the periphery
(spi, i2c, sdcard, dac) does not need to know the internals of the dma.
A standard I2C address is 7 bits but addresses 0b0000xxx and 0b1111xxx
are reserved. The scan() method is changed to reflect this, along with
the docs.
The L4 MCU supports 40 Events/IRQs lines of the type configurable and
direct. But this L4 port only supports configurable line types which are
already supported by uPy. For details see page 330 of RM0351, Rev 1.
The USB_FS_WAKUP event is a direct type and there is no support for it.
__GPIOI_CLK_ENABLE is defined in hal/l4/inc/Legacy/stm32_hal_legacy.h
as __HAL_RCC_GPIOI_CLK_ENABLE, and that latter macro is not defined
anywhere else (because the L4 does not have port GPIOI). So the test
for GPIOI is needed, along with the test for the CLK_ENABLE macro.
L4 does not have UART6, and has similar registers to the F7.
Original patch was authored by Tobias Badertscher / @tobbad, but it was
reworked to split UART edits from USB edits.
64-bit integer division brings a dependency on library functions. It is
avoided here by dividing fck and baud by a common divisior. The error
is the better (1/(2*0x300)) as with 64 bit division (1/(0x300)).
These files come from STM32Cube_FW_L4_V1.3.0, with Windows line endings
converted to unix. Only basic HAL files are added. In addition the QSPI
support is included to support later external QSPI flash as mass storage.
- add template rule that converts a specified source file into a qstring file
- add special rule for generating a central header that contains all
extracted/autogenerated strings - defined by QSTR_DEFS_COLLECTED
variable. Each platform appends a list of sources that may contain
qstrings into a new build variable: SRC_QSTR. Any autogenerated
prerequisities are should be appened to SRC_QSTR_AUTO_DEPS variable.
- remove most qstrings from py/qstrdefs, keep only qstrings that
contain special characters - these cannot be easily detected in the
sources without additional annotations
- remove most manual qstrdefs, use qstrdef autogen for: py, cc3200,
stmhal, teensy, unix, windows, pic16bit:
- remove all micropython generic qstrdefs except for the special strings that contain special characters (e.g. /,+,<,> etc.)
- remove all port specific qstrdefs except for special strings
- append sources for qstr generation in platform makefiles (SRC_QSTR)
The config variable MICROPY_MODULE_FROZEN is now made of two separate
parts: MICROPY_MODULE_FROZEN_STR and MICROPY_MODULE_FROZEN_MPY. This
allows to have none, either or both of frozen strings and frozen mpy
files (aka frozen bytecode).
tools/pydfu.py is now the recommended way of deploying a DFU file. Old
behaviour of dfu-util can be obtained by passing USE_PYDFU=0 when invoking
make.
The main README.md file has been updated to reflect this change.
If None was returned for such requests (which likely means that user simply
didn't handle them), it means successful init and default sector size of 512
bytes respectively. This makes only BP_IOCTL_SEC_COUNT a mandatory request,
and thus re-establishes parity with old interface, where only .count() is
mandatory().
This patch adds support to fsusermount for multiple block devices
(instead of just one). The maximum allowed is fixed at compile time by
the size of the fs_user_mount array accessed via MP_STATE_PORT, which
in turn is set by MICROPY_FATFS_VOLUMES.
With this patch, stmhal (which is still tightly coupled to fsusermount)
is also modified to support mounting multiple devices And the flash and
SD card are now just two block devices that are mounted at start up if
they exist (and they have special native code to make them more
efficient).
You can now create (singleton) objects representing the flash and SD
card, using:
flash = pyb.Flash()
sdcard = pyb.SDCard()
These objects provide the block protocol.
