98c5703027
It uses non-blocking transfer of data. Advantage over SoftI2C: - Higher data rate up to ~3 MHZ. - Full protocol support.
59 lines
2.6 KiB
C
59 lines
2.6 KiB
C
#define MICROPY_HW_BOARD_NAME "Teensy 4.1"
|
|
#define MICROPY_HW_MCU_NAME "MIMXRT1062DVJ6A"
|
|
|
|
#define BOARD_FLASH_SIZE (8 * 1024 * 1024)
|
|
|
|
// Teensy 4.1 has 1 board LED
|
|
#define MICROPY_HW_LED1_PIN (pin_GPIO_B0_03)
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
|
#define BOARD_FLASH_CONFIG_HEADER_H "teensy41_flexspi_nor_config.h"
|
|
|
|
#define MICROPY_HW_NUM_PIN_IRQS (4 * 32 + 3)
|
|
|
|
// UART config: 8 UARTs at the pins for Teensy 4.1
|
|
#define MICROPY_HW_UART_NUM (sizeof(uart_index_table) / sizeof(uart_index_table)[0])
|
|
#define MICROPY_HW_UART_INDEX { 0, 6, 4, 2, 3, 8, 1, 7, 5 }
|
|
|
|
#define IOMUX_TABLE_UART \
|
|
{ IOMUXC_GPIO_AD_B0_12_LPUART1_TX }, { IOMUXC_GPIO_AD_B0_13_LPUART1_RX }, \
|
|
{ IOMUXC_GPIO_AD_B1_02_LPUART2_TX }, { IOMUXC_GPIO_AD_B1_03_LPUART2_RX }, \
|
|
{ IOMUXC_GPIO_AD_B1_06_LPUART3_TX }, { IOMUXC_GPIO_AD_B1_07_LPUART3_RX }, \
|
|
{ IOMUXC_GPIO_B1_00_LPUART4_TX }, { IOMUXC_GPIO_B1_01_LPUART4_RX }, \
|
|
{ IOMUXC_GPIO_B1_12_LPUART5_TX }, { IOMUXC_GPIO_B1_13_LPUART5_RX }, \
|
|
{ IOMUXC_GPIO_AD_B0_02_LPUART6_TX }, { IOMUXC_GPIO_AD_B0_03_LPUART6_RX }, \
|
|
{ IOMUXC_GPIO_EMC_31_LPUART7_TX }, { IOMUXC_GPIO_EMC_32_LPUART7_RX }, \
|
|
{ IOMUXC_GPIO_AD_B1_10_LPUART8_TX }, { IOMUXC_GPIO_AD_B1_11_LPUART8_RX },
|
|
|
|
#define MICROPY_HW_SPI_INDEX { 4, 3, 1 }
|
|
|
|
#define IOMUX_TABLE_SPI \
|
|
{ IOMUXC_GPIO_SD_B0_00_LPSPI1_SCK }, { IOMUXC_GPIO_SD_B0_01_LPSPI1_PCS0 }, \
|
|
{ IOMUXC_GPIO_SD_B0_02_LPSPI1_SDO }, { IOMUXC_GPIO_SD_B0_03_LPSPI1_SDI }, \
|
|
{ 0 }, { 0 }, \
|
|
{ 0 }, { 0 }, \
|
|
{ IOMUXC_GPIO_AD_B1_15_LPSPI3_SCK }, { IOMUXC_GPIO_AD_B1_12_LPSPI3_PCS0 }, \
|
|
{ IOMUXC_GPIO_AD_B1_14_LPSPI3_SDO }, { IOMUXC_GPIO_AD_B1_13_LPSPI3_SDI }, \
|
|
{ IOMUXC_GPIO_B0_03_LPSPI4_SCK }, { IOMUXC_GPIO_B0_00_LPSPI4_PCS0 }, \
|
|
{ IOMUXC_GPIO_B0_02_LPSPI4_SDO }, { IOMUXC_GPIO_B0_01_LPSPI4_SDI },
|
|
|
|
#define DMA_REQ_SRC_RX { 0, kDmaRequestMuxLPSPI1Rx, kDmaRequestMuxLPSPI2Rx, \
|
|
kDmaRequestMuxLPSPI3Rx, kDmaRequestMuxLPSPI4Rx }
|
|
|
|
#define DMA_REQ_SRC_TX { 0, kDmaRequestMuxLPSPI1Tx, kDmaRequestMuxLPSPI2Tx, \
|
|
kDmaRequestMuxLPSPI3Tx, kDmaRequestMuxLPSPI4Tx }
|
|
|
|
// Define mapping hardware I2C # to logical I2C #
|
|
// SDA/SCL HW-I2C Logical I2C
|
|
// 17/16 LPI2C3 -> 0
|
|
// 18/19 LPI2C1 -> 1
|
|
// 25/24 LPI2C4 -> 2
|
|
|
|
#define MICROPY_HW_I2C_INDEX { 1, 3, 4 }
|
|
|
|
#define IOMUX_TABLE_I2C \
|
|
{ IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL }, { IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA }, \
|
|
{ 0 }, { 0 }, \
|
|
{ IOMUXC_GPIO_AD_B1_07_LPI2C3_SCL }, { IOMUXC_GPIO_AD_B1_06_LPI2C3_SDA }, \
|
|
{ IOMUXC_GPIO_AD_B0_12_LPI2C4_SCL }, { IOMUXC_GPIO_AD_B0_13_LPI2C4_SDA },
|