Unify USB-related makefile var and C def as CIRCUITPY_USB.
Always define it as 0 or 1, same as all other settings.
USB_AVAILABLE was conditionally defined in supervisor.mk,
but never actually used to #ifdef USB-related code.
Loosely related to #4546
It is required to call .dirty() with appropriate arguments after modifications through the buffer protocol, or the display might not be updated correctly.
This is a modest code savings, but more importantly it reduces
boilerplate in bitmap-modifying routines.
Callers need only ensure they call displayio_bitmap_set_dirty_area in
advance of the bitmap modifications they perform.
(note that this assumes that no bitmap operation can enter background
tasks. If an operation COULD enter background tasks, it MUST re-dirty
the area it touches when it exits, simply by a fresh call to
set_dirty_area with the same area as before)
.. simplifying code in the process. For instance, now fill_region
uses area routines to order and constrain its coordinates.
Happily, this change also frees a modest amount of code space.
.. and simplify the implmentation of displayio_area_union
This _slightly_ changes the behavior of displayio_area_union:
Formerly, if one of the areas was empty, its coordinates were still
used in the min/max calculations.
Now, if one of the areas is empty, the result gets the other area's coords
In particular, taking the union of the empty area with coords (0,0,0,0)
with the non-empty area (x1,y1,x2,y2) would give the area (0,0,x2,y2)
before, and (x1,y1,x2,y2) after the change.
When reading uncompressed bitmap data directly, readinto can work
much more quickly than a Python-coded loop.
On a Raspberry Pi Pico, I benchmarked a modified version of
adafruit_bitmap_font's pcf reader which uses readinto instead of
the existing code. My test font was a 72-point file created from Arial.
This decreased the time to load all the ASCII glyphs from 4.9 seconds to
just 0.44 seconds.
While this attempts to support many pixel configurations (1/2/4/8/16/24/32
bpp; swapped words and pixels) only the single combination used by
PCF fonts was tested.
This is a first go at it, done by naive replacing of all array
operations with corresponding operations on the list. Note that
there is a lot of unnecessary type conversions, here. Also, list_pop
has been copied, because it's decalerd STATIC in py/objlist.h
Since we want to expose the list of group's children to the user,
we should only have the original objects in it, without any other
additional data, and compute the native object as needed.
* Comment on the reason for scaling by 256
* Divide by 256 instead of shifting
* fix a cast; eliminate an unneeded roundf() to get a few bytes code back
On the Pico, this increases the "fill rate" of
pixels[:] = newvalues
considerably. On a strip of 240 RGB LEDs, auto_write=False, the timings
are:
|| Brightness || Before || After || Improvement ||
|| 1.0 || 117 kpix/s || 307 kpix/s || 2.62x ||
|| 0.07 || 117 kpix/s || 273 kpix/s || 2.33x ||
It's worth noting that even the "before" rate is fast compared to the
time to transmit a single neopixel, but any time we can gain back
in the whole pipeline will let marginal animations work a little better.
To set all the pixels in this way and then show() gives a pleasant bump
to the framerate, from about 108Hz to 124Hz (1.15x)
The main source of speed-up is using integer math instead of floating
point math for the calculation of the post-scaled pixel values. A slight
secondary gain is achieved by avoiding the scaling altogether when
the scale factor is 1.0.
Because the math is not exactly the same, some scaled pixel values may
change by +- 1 RGBW "step". In practice, this is unlikely to matter.
The gains are bigger on the Pico and other M0 microcontrollers than M4
microcontrollers with floating point math in the hardware.
Happily, flash size is also improved a bit on the Pico build I did,
going from
> 542552 bytes used, 506024 bytes free in flash firmware space out of 1048576 bytes (1024.0kB).
to
> 542376 bytes used, 506200 bytes free in flash firmware space out of 1048576 bytes (1024.0kB).
Also found a race condition between timer_disable and redraw, which
would happen if I debugger-paused inside common_hal_rgbmatrix_timer_disable
or put a delay or print inside it. That's what pausing inside reconstruct
fixes.
So that the "right timer" can be chosen, `timer_allocate` now gets the `self`
pointer. It's guaranteed at this point that the pin information is accurate,
so you can e.g., find a PWM unit related to the pins themselves.
This required touching each port to add the parameter even though it's
unused everywhere but raspberrypi.
* Introduce explicit serpentine: bool argument instead of using negative
numbers (thanks, ghost of @tannewt sitting on one shoulder)
* Fix several calculations of height
Testing performed (matrixportal):
* set up a serpentine 64x64 virtual display with 2 64x32 tiles
* tried all 4 rotations
* looked at output of REPL
Changed calls: PointSize(), LineWidth(), VertexTranslateX() and VertexTranslateY()
Units for all the above are now pixels, not fixed-point integers. This matches OpenGL.
Docstrings updated accordingly
The RP2040 is new microcontroller from Raspberry Pi that features
two Cortex M0s and eight PIO state machines that are good for
crunching lots of data. It has 264k RAM and a built in UF2
bootloader too.
Datasheet: https://pico.raspberrypi.org/files/rp2040_datasheet.pdf
