Helps prevent the filesystem from getting formatted by mistake, among other
things. For example, on a Pico board, entering Ctrl+D and Ctrl+C fast many
times will eventually wipe the filesystem (without warning or notice).
Further rationale: Ctrl+C is used a lot by automation scripts (eg mpremote)
and UI's (eg Mu, Thonny) to get the board into a known state. If the board
is not responding for a short time then it's not possible to know if it's
just a slow start up (eg in _boot.py), or an infinite loop in the main
application. The former should not be interrupted, but the latter should.
The only way to distinguish these two cases would be to wait "long enough",
and if there's nothing on the serial after "long enough" then assume it's
running the application and Ctrl+C should break out of it. But defining
"long enough" is impossible for all the different boards and their possible
behaviour. The solution in this commit is to make it so that frozen
start-up code cannot be interrupted by Ctrl+C. That code then effectively
acts like normal C start-up code, which also cannot be interrupted.
Note: on the stm32 port this was never seen as an issue because all
start-up code is in C. But now other ports start to put more things in
_boot.py and so this problem crops up.
Signed-off-by: David Grayson <davidegrayson@gmail.com>
All board pins that have UART's assigned can be used. Baud rate range is
75 Baud to ~2 MBaud.
No flow control yet, and only RX is buffered. TX buffer and flow control
may be added later for SAMD51 with its larger RAM and Flash.
Its API conforms to the docs. There are 16 IRQ channels available, which
will be used as assignable to the GPIO numbers. In most cases, the irq
channel is GPIO_no % 16.
Features are:
- 3 to 5 different frequency groups.
- Freq range of 1Hz - 24 MHz.
- Duty rate stays stable on freq change.
Keyword options to the PWM constructor:
- device=n Select a specific PWM device. If no device is specified, a free
device is chosen, if available at that pin.
- freq=nnnn
- duty_u16=nnnn
- duty_ns=nnnn
- invert=True/False Allowing two outputs on the same device/channel to have
complementary signals.
If both freq and duty are provided, PWM output will start immediately.
Pins at the same device have the same frequency. If the PWM output number
exceeds the number of channels at the PWM device, the effctive channel_no
is output_no % channel_count. So with a channel count of 4, output 7 is
assigned to channel 3. Pins at a certain channel have the same frequency
and duty rate, but may be seperately inverted.
With the method read_u16(). Keyword arguments of the constructor are:
- bits=n The resolution; default is 12.
- average=n The average of samples, which are taken and cumulated. The
default value is 16. Averaging by hw is faster than averaging
in code.
The ADC runs at a clock freq 1.5 MHz. A single 12 bit conversion takes
8 microseconds.
For ports with MICROPY_VFS and MICROPY_PY_IO enabled their configuration
can now be simplified to use the defaults for mp_import_stat and
mp_builtin_open.
This commit makes no functional change, except for the following minor
points:
- the built-in "open" is removed from the minimal port (it previously did
nothing)
- the duplicate built-in "input" is removed from the esp32 port
- qemu-arm now delegates to VFS import/open
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_PY_SYS_PATH_ARGV_DEFAULTS is enabled (which it is by default)
then sys.path and sys.argv will be initialised and populated with default
values. This keeps all bare-metal ports aligned.
Signed-off-by: Damien George <damien@micropython.org>
- Makefile: update to use new ASF4 files, support frozen manifest, and
include source files in upcoming commits
- boards/manifest.py: add files to freeze
- boards/samd51p19a.ld: add linker script for this MCU
- help.c: add custom help text
- main.c: execute _boot.py, boot.py and main.py on start-up
- modules/_boot.py: startup file to freeze
- modutime.c: add gmtime, localtime, mktime, time functions
- mpconfigport.h: enabled more features for sys and io and modules
- mphalport.h: add mp_hal_pin_xxx macros
- mphalport.c: add mp_hal_stdio_poll
No functionality change is intended with this commit, it just consolidates
the separate implementations of GC helper code to the lib/utils/ directory
as a general set of helper functions useful for any port. This reduces
duplication of code, and makes it easier for future ports or embedders to
get the GC implementation correct.
Ports should now link against gchelper_native.c and either gchelper_m0.s or
gchelper_m3.s (currently only Cortex-M is supported but other architectures
can follow), or use the fallback gchelper_generic.c which will work on
x86/x64/ARM.
The gc_helper_get_sp function from gchelper_m3.s is not really GC related
and was only used by cc3200, so it has been moved to that port and renamed
to cortex_m3_get_sp.
