Commit Graph

34 Commits

Author SHA1 Message Date
Chris Mason d61e7a6d8a stm32/uart: Add support for UART4/5 on L0 MCUs. 2019-12-05 15:31:41 +11:00
iabdalkader f7a07b3605 stm32: Add support for FDCAN peripheral, exposed as pyb.CAN.
The new fdcan.c file provides the low-level C interface to the FDCAN
peripheral, and pyb_can.c is updated to support both traditional CAN and
FDCAN, depending on the MCU being compiled for.
2019-09-23 17:00:54 +10:00
Damien George 97e8e036c5 stm32/usbd: Support USB device mode on STM32L432 MCUs. 2019-08-15 12:46:04 +10:00
Damien George bf733c27bb stm32/usbd: Introduce MICROPY_HW_USB_IS_MULTI_OTG to simplify USB config
This is an internal config value that is enabled for MCUs that have
multiple OTG instances, to simplify #if configuration of the USB code.
2019-08-15 12:19:28 +10:00
Chris Wilson 3d02ebb4e8 stm32/sdcard: Support configuring the SD/MMC bus width to 1 or 4 bits.
Some SD/MMC breakout boards don't support 4-bit bus mode.  This adds a new
macro MICROPY_HW_SDMMC_BUS_WIDTH that allows each board to define the width
of the SD/MMC bus interface used on that board, defaulting to 4 bits.
2019-08-08 12:53:05 +10:00
Damien George 59b7166d87 stm32: Add initial support for STM32WBxx MCUs.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor.  The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it.  Supported
features so far include: RTC, UART, USB, internal flash filesystem.
2019-07-17 16:33:31 +10:00
Damien George f302f784e9 stm32/usb: Add config options to disable USB MSC and/or HID.
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID.  They are both
enabled by default.
2019-07-16 14:39:21 +10:00
Damien George 23d9c6a0fd stm32: Add initial support for STM32L0xx MCUs. 2019-07-05 17:24:59 +10:00
Damien George 0c29502ad9 stm32/usb: Refactor CDC VCP code to enable N CDC interfaces.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
2019-05-30 21:11:04 +10:00
Damien George ddc657658a stm32/machine_i2c: Simplify ROM initialisation of static HW I2C objects. 2019-05-21 12:38:34 +10:00
Andrew Leech ed2b6ea0a8 stm32/i2c: Make timeout for hardware I2C configurable.
Previously the hardware I2C timeout was hard coded to 50ms which isn't
guaranteed to be enough depending on the clock stretching specs of the I2C
device(s) in use.

This patch ensures the hardware I2C implementation honors the existing
timeout argument passed to the machine.I2C constructor.  The default
timeout for software and hardware I2C is now 50ms.
2019-05-21 12:20:19 +10:00
Chris Mason 1b956ec817 stm32: Add support for F413 MCUs.
Includes:
- Support for CAN3.
- Support for UART9 and UART10.
- stm32f413xg.ld and stm32f413xh.ld linker scripts.
- stm32f413_af.csv alternate function mapping.
- startup_stm32f413xx.s because F413 has different interrupt vector table.
- Memory configuration with: 240K filesystem, 240K heap, 16K stack.
2019-05-02 16:26:53 +10:00
Damien George 46e5d6b889 stm32/rtc: Add auto-LSE-bypass detection with fallback to LSE then LSI.
If MICROPY_HW_RTC_USE_BYPASS is enabled the RTC startup goes as follows:
- RTC is started with LSE in bypass mode to begin with
- if that fails to start (after a given timeout) then LSE is reconfigured
  in non-bypass
- if that fails to start then RTC is switched to LSI
2019-04-11 12:09:21 +10:00
Damien George 7ce2a08231 stm32: Add support for MMC driver, exposed via pyb.MMCard class.
Enable it via MICROPY_HW_ENABLE_MMCARD.
2019-04-01 17:04:43 +11:00
Damien George 9670b26526 stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD.
For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 15:21:26 +11:00
Francisco J. Manno f938e70c69 stm32: Add compile-time option to use HSI as clock source.
To use HSI instead of HSE define MICROPY_HW_CLK_USE_HSI as 1 in the board
configuration file.  The default is to use HSE.

HSI has been made the default for the NUCLEO_F401RE board to serve as an
example, and because early revisions of this board need a hardware
modification to get HSE working.
2019-03-05 15:49:08 +11:00
Andrew Leech ce0c581179 stm32/main: Add board config option to enable/disable mounting SD card.
The new option MICROPY_HW_SDCARD_MOUNT_AT_BOOT can now be defined to 0 in
mpconfigboard.h to allow SD hardware to be enabled but not auto-mounted at
boot.  This feature is enabled by default to retain previous behaviour.

Previously, if an SD card is enabled in hardware it is also used to boot
from.  While this can be disabled with a SKIPSD file on internal flash,
this wont be available at first boot or if the internal flash gets
corrupted.
2018-12-22 01:30:47 +11:00
Andrew Leech 338635ccc6 stm32/main: Add configuration macros for board to set heap start/end.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).

As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot.  On boards with SDRAM enabled the heap
has been set to use that.
2018-10-05 17:30:18 +10:00
Andrew Leech 84f4d58479 stm32/dcmi: Add F4/F7/H7 hal files and dma definitions for DCMI periph. 2018-09-21 12:12:49 +10:00
Damien George ea7e747979 stm32: Add support for STM32F0 MCUs. 2018-05-28 21:49:49 +10:00
Damien George f497723802 stm32: Allow to have no storage support if there are no block devices.
If no block devices are defined by a board then storage support will be
disabled.  This means there is no filesystem provided by either the
internal flash or external SPI flash.  But the VFS system can still be
enabled and filesystems provided on external devices like an SD card.
2018-05-28 21:45:46 +10:00
Ryan Shaw b9ff46f1ed stm32: Enable UART7/8 on F4 series that have these peripherals. 2018-05-16 11:55:07 +10:00
Damien George 92c5e2708d stm32/modpyb: Introduce MICROPY_PY_PYB_LEGACY config option for pyb mod.
This is enabled by default.  When it is disabled all legacy functions and
classes in the pyb module are excluded from the build.
2018-05-14 13:49:22 +10:00
Damien George 8a949ba599 stm32: Introduce MICROPY_PY_STM config to include or not the stm module.
By default the stm module is included in the build, but a board can now
define MICROPY_PY_STM to 0 to not include this module.  This reduces the
firmware by about 7k.
2018-04-24 12:01:49 +10:00
Damien George 3d5d76fb73 stm32/main: Allow a board to configure the label of the flash FS.
To change the default label a board should define:

    #define MICROPY_HW_FLASH_FS_LABEL "label"
2018-04-11 16:52:22 +10:00
Damien George cf9fc7346d stm32: Allow a board to configure the HSE in bypass mode.
To use HSE bypass mode the board should define:

    #define MICROPY_HW_CLK_USE_BYPASS (1)

If this is not defined, or is defined to 0, then HSE oscillator mode is
used.
2018-04-11 16:46:47 +10:00
Damien George a7ebac2eae stm32/can: Allow CAN pins to be configured per board.
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI).  To enable CAN on a board the mpconfigboard.h file should
define (for example):

    #define MICROPY_HW_CAN1_TX (pin_B9)
    #define MICROPY_HW_CAN1_RX (pin_B8)
    #define MICROPY_HW_CAN2_TX (pin_B13)
    #define MICROPY_HW_CAN2_RX (pin_B12)

And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
2018-04-11 16:35:24 +10:00
Damien George b833f170c3 stm32/main: Only update reset_mode if board doesn't use a bootloader.
If the board is configured to use a bootloader then that bootloader will
pass through the reset_mode.
2018-03-29 16:16:58 +11:00
Damien George 626d6c9756 stm32/storage: Introduce MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE cfg.
This config variable controls whether to support storage on the internal
flash of the MCU.  It is enabled by default and should be explicitly
disabled by boards that don't want internal flash storage.
2018-03-10 00:59:43 +11:00
iabdalkader 61d463ad07 stm32/mpconfigboard_common: Add STM32H7 common configuration. 2018-03-09 15:12:44 +11:00
Damien George 989fc16162 stm32: Move MCU-specific cfg from mphalport.h to mpconfigboard_common.h.
It's cleaner to have all the MCU-specific configuration in one location,
not least to help with adding support for a new MCU series.
2018-02-23 16:54:07 +11:00
Damien George 60b0982bb2 stm32: Add board config option to enable/disable the ADC.
The new option is MICROPY_HW_ENABLE_ADC and is enabled by default.
2018-02-22 14:22:45 +11:00
Damien George 5c320bd0b0 stm32: Introduce MICROPY_HW_ENABLE_USB and clean up USB config.
This patch allows to completely compile-out support for USB, and no-USB is
now the default.  If a board wants to enable USB it should define:

    #define MICROPY_HW_ENABLE_USB (1)

And then one or more of the following to select the USB PHY:

    #define MICROPY_HW_USB_FS (1)
    #define MICROPY_HW_USB_HS (1)
    #define MICROPY_HW_USB_HS_IN_FS (1)
2018-02-13 18:51:08 +11:00
Damien George 2d5bab46be stm32: Add mpconfigboard_common.h with common/default board settings.
This file mirrors py/mpconfig.h but for board-level config options.  It
provides a default configuration, to be overridden by a specific
mpconfigboard.h file, as well as setting up certain macros to automatically
configure a board.
2018-02-09 18:40:13 +11:00