Commit Graph

17 Commits

Author SHA1 Message Date
Damien George aed1da913b stmhal: L4: Modify usbd_conf.c to support L4 MCU.
Original patch was authored by Tobias Badertscher / @tobbad, but it was
reworked to split UART edits from USB edits.
2016-04-17 12:02:26 +01:00
Martin Fischer 8a8e775035 stmhal: Consistently enable USB SOF Irqs for all USB modes (FS and HS).
SOF irqs are now standard for rx/tx USB transfers, so enable them for both
FS and HS modes.  Fixes #1944.
2016-04-07 09:23:33 +01:00
Damien George d363133917 stmhal: Make USB CDC driver use SOF instead of TIM3 for outgoing data.
Previous to this patch the USB CDC driver used TIM3 to trigger the
sending of outgoing data over USB serial.  This patch changes the
behaviour so that the USB SOF interrupt is used to trigger the processing
of the sending.  This reduces latency and increases bandwidth of outgoing
data.

Thanks to Martin Fischer, aka @hoihu, for the idea and initial prototype.

See PR #1713.
2016-01-29 15:21:43 +00:00
neilh10 1be0fde45c stmhal: Enable two USB phys to be supported together.
This is refactoring to enable support for the two USB PHYs available on
some STM32F4 processors to be used at the same time. The F405/7 & F429
have two USB PHYs, others such as the F411 only have one PHY.

This has been tested separately on a pyb10 (USB_FS PHY) and F429DISC
(USB_HS PHY) to be able to invoke a REPL/USB.  I have modified a PYBV10
to support two PHYs.

The long term objective is to support a 2nd USB PHY to be brought up as a
USB HOST, and possibly a single USB PHY to be OTG.
2015-12-09 09:56:36 +00:00
Dave Hylands 061eb6fa6b stmahl: Fix usbd_conf.c for devices which don't have USB_HS at all.
The STMCube examples define both USE_USB_HS and USE_USB_HS_IN_FS when they
use the HS in FS mode.

The STM32F401 doesn't have a USB_HS at all, so the USB_OTG_HS instance
doesn't even exist.
2015-11-26 16:17:26 +00:00
Tobias Badertscher 8844d031e4 stmhal: Add support for the STM32F429I-DISCO kit by STMicro. 2015-11-25 23:53:26 +00:00
Dave Curtis 32b3549cce stmhal: Add symbolic #defines for interrupt levels in irq.h. 2015-11-01 23:23:39 +00:00
Dave Hylands ea8bf81058 stmhal: Replace #include "stm32f4xx_hal.h" with #include STM32_HAL_H. 2015-07-30 00:38:25 +01:00
Damien George 73f1a49137 stmhal: Exclude USB HS code when USB HS mode not enabled. 2015-04-18 21:40:58 +01:00
Damien George 50912e7f5d py, unix, stmhal: Allow to compile with -Wshadow.
See issue #699.
2015-01-20 11:55:10 +00:00
Damien George 131185a2b8 stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards.
This config option is for the USB OTG pin, pin A10.  This is used on
some boards but not others.  Eg PYBv3 uses PA10 for LED(2), so it
shouldn't be used for OTG ID (actually PA10 is multiplexed on this
board, but defaults to LED(2)).

Partially addresses issue #1059.
2015-01-12 16:13:29 +00:00
Damien George 181bfb6db2 stmhal: Add MICROPY_HW_USB_VBUS_DETECT_PIN option, for boards without it
Since all currently supported boards use pin A9 for this function, the
value of the macro MICROPY_HW_USB_VBUS_DETECT_PIN is not actually used,
just the fact that it is defined.

Addresses issue #1048.
2015-01-07 23:54:57 +00:00
bvernoux 569aa90137 micropython port for HydraBus 2014-06-02 21:43:02 +02:00
Damien George 04b9147e15 Add license header to (almost) all files.
Blanket wide to all .c and .h files.  Some files originating from ST are
difficult to deal with (license wise) so it was left out of those.

Also merged modpyb.h, modos.h, modstm.h and modtime.h in stmhal/.
2014-05-03 23:27:38 +01:00
Damien George fb25c2d95f stmhal: USB CDC and MSC device work together. 2014-03-22 12:32:54 +00:00
Dave Hylands 0a64c92a9c stmhal - add led support. Add netduino_plus_2 support
Tweaked a couple of the USB files to compile if neither dev nor host was defined.
Tested on netduiono plus 2 and stm32f4discovery boards
2014-03-14 09:48:49 -07:00
Damien George b30c02afa0 stmhal: Get USB enumerating a CDC device.
Enumerates CDC device over USB, but doesn't transmit/receive yet.
2014-03-14 00:30:37 +00:00