There are enough places that implement __exit__ by forwarding directly to
mp_stream_close that this saves code size.
For the cases where __exit__ is a no-op, additionally make their
MP_STREAM_CLOSE ioctl handled as a no-op.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds initial support for STM32H5xx MCUs. The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot
Signed-off-by: Damien George <damien@micropython.org>
Also fix MAX_ENDPOINT definition for G0, which follows G4.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The goal here is to remove a slot (making way to turn make_new into a slot)
as well as reduce code size by the ~40 references to mp_identity_getiter
and mp_stream_unbuffered_iter.
This introduces two new type flags:
- MP_TYPE_FLAG_ITER_IS_ITERNEXT: This means that the "iter" slot in the
type is "iternext", and should use the identity getiter.
- MP_TYPE_FLAG_ITER_IS_CUSTOM: This means that the "iter" slot is a pointer
to a mp_getiter_iternext_custom_t instance, which then defines both
getiter and iternext.
And a third flag that is the OR of both, MP_TYPE_FLAG_ITER_IS_STREAM: This
means that the type should use the identity getiter, and
mp_stream_unbuffered_iter as iternext.
Finally, MP_TYPE_FLAG_ITER_IS_GETITER is defined as a no-op flag to give
the default case where "iter" is "getiter".
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Previously the desired output type was specified. Now make the type part
of the function name. Because this function is used in a few places this
saves code size due to smaller call-site.
This makes `mp_obj_new_str_type_from_vstr` a private function of objstr.c
(which is almost the only place where the output type isn't a compile-time
constant).
This saves ~140 bytes on PYBV11.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This reduces code size and code duplication, and fixes `pyb.usb_mode()` so
that it now returns the correct string when in multi-VCP mode (before, it
would return None when in one of these modes).
Signed-off-by: Damien George <damien@micropython.org>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
This much buffer space is required for CDC data out endpoints to avoid any
buffer overflows when the USB CDC is saturated with data.
Signed-off-by: Damien George <damien@micropython.org>
There are a maximum of 8 USB endpoints and each has 2 buffer slots
(in/out). This commit add support for up to 8 endpoints and adds FIFO
configuration for USB profiles with 2xVCP on MCUs that have device-only USB
peripherals.
Tested on NUCLEO_WB55 in 2xVCP, 2xVCP+MSC and 2xVCP+MSC+HID mode.
Signed-off-by: Damien George <damien@micropython.org>
Most types are in rodata/ROM, and mp_obj_base_t.type is a constant pointer,
so enforce this const-ness throughout the code base. If a type ever needs
to be modified (eg a user type) then a simple cast can be used.
Enabled by default, but disabled when REPL is connected to the VCP (this is
the existing behaviour). Can be configured at run-time with, eg:
pyb.USB_VCP().init(flow=pyb.USB_VCP.RTS | pyb.USB_VCP.CTS)
The previous version did not work on MCUs that only had USB device mode
(compared to OTG) because of the handling of NAK. And this previous
handling of NAK had a race condition where a new packet could come in
before USBD_HID_SetNAK was called (since USBD_HID_ReceivePacket clears NAK
as part of its operation). Furthermore, the double buffering of incoming
reports was not working, only one buffer could be used at a time.
This commit rewrites the HID interface code to have a single incoming
buffer, and only calls USBD_HID_ReceivePacket after the user has read the
incoming report (similar to how the VCP does its flow control). As such,
USBD_HID_SetNAK and USBD_HID_ClearNAK are no longer needed.
API functionality from the user's point of view should be unchanged with
this commit.
The new configurations MICROPY_HW_USB_MSC and MICROPY_HW_USB_HID can be
used by a board to enabled or disable MSC and/or HID. They are both
enabled by default.
If both FS and HS USB peripherals are enabled for a board then the active
one used for the REPL will now be auto-detected, by checking to see if both
the DP and DM lines are actively pulled low. By default the code falls
back to use MICROPY_HW_USB_MAIN_DEV if nothing can be detected.
Commit 9e68eec8ea introduced a regression
where the PID of the USB device would be 0xffff if the default value was
used. This commit fixes that by using a signed int type.
With this the user can select multiple logical units to expose over USB MSC
at once, eg: pyb.usb_mode('VCP+MSC', msc=(pyb.Flash(), pyb.SDCard())). The
default behaviour is the original behaviour of just one unit at a time.
SCSI can support multiple logical units over the one interface (in this
case over USBD MSC) and here the MSC code is reworked to support this
feature. At this point only one LU is used and the behaviour is mostly
unchanged from before, except the INQUIRY result is different (it will
report "Flash" for both flash and SD card).
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
Before this change, if the USB was reconnected it was possible that some
characters in the TX buffer were retransmitted because tx_buf_ptr_out and
tx_buf_ptr_out_shadow were reset while tx_buf_ptr_in wasn't. That
behaviour is fixed here by retaining the TX buffer state across reconnects.
Fixes issue #4761.
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
With this and previous patches the stm32 port can now be compiled using
object representation D (nan boxing). Note that native code and frozen mpy
files with float constants are currently not supported with this object
representation.
This patch adds the configuration MICROPY_HW_USB_ENABLE_CDC2 which enables
a new USB device configuration at runtime: VCP+VCP+MSC. It will give two
independent VCP interfaces available via pyb.USB_VCP(0) and pyb.USB_VCP(1).
The first one is the usual one and has the REPL on it. The second one is
available for general use.
This configuration is disabled by default because if the mode is not used
then it takes up about 2200 bytes of RAM. Also, F4 MCUs can't support this
mode on their USB FS peripheral (eg PYBv1.x) because they don't have enough
endpoints. The USB HS peripheral of an F4 supports it, as well as both the
USB FS and USB HS peripherals of F7 MCUs.
