Everything should be using the keypad module instead.
Note: there are several boards that still had gamepadshift enabled. I
did not contact their authors to make sure they already switched to
keypad in their code and documentation. We should probably wait with
merging this for their go ahead.
There were two main issues with the PWM support.
The first is they would fail to work properly if the board goes
into low power mode, when you do things like: time.sleep(0.25)
Can make partially work with this by turning on the proper flags
in each of the FlexPWMTimer Timers/sub-timers, but this did not
appear to work if for example you have both A and B channels
enabled.
Second main problem is that the code did not work with the X
channel of each timer/sub-timer. It looks like someone had
earlier started support for this, But was not sufficient.
Needed to bypass the SDK code and get it closer to the PJRC code.
That is we set the PWM_CTRL_FULL_MASK, which then uses base->SM[submodule].VAL1 to control
when the timer is reset, so it sets up your cycle/frequency. But then this implies that X channel
which uses 0, 1 has to be handled specially. So for the different channels:
A - Uses VAL2 to turn on (0) and VAL3=duty to turn off
B - Uses VAL4 to turn on (0) and VAL5 to turn off
X - As mentioned above VAL1 turns off, but its set to the timing for freqency. so
VAL0 turns on, so we set it to VAL1 - duty
As mentioned in issue #6241 the commit to setup port hooks is now
causing all input/output that are to go to the Mu window to also
go to the LpUart that is defined the port serial.c
and in this case it goes to lpuart4, which on Teensy 4, 4.1 is
used on Arduino Serial2. With this new code this port no longer
works properly.
This is one way to solve it, in that there is a #if defined() that
if not set, all of the code in this file is ignored and the higher
level supervisor stub versions of these functions will be used, which
don't interfere with Serial2 and my test sketch works again.
Note: the PR for Switch to Port Serial Hooks, also changed code in
other ports. I have not tried to see how.
There are other more global fixes for this, in which maybe a higer
level #if that disables the code within the top level supervisor. Or
could be software controlled
Again this may not be the final solution, but at least it gets
Serial2 up and running agin.
This allows you to list and explore connected USB devices. It
only stubs out the methods to communicate to endpoints. That will
come in a follow up once TinyUSB has it. (It's in progress.)
Related to #5986
There is a race between when we run background tasks and when we
sleep. If an interrupt happens between the two, then we may delay
executing the background task. On some ports we checked this for
TinyUSB already. On iMX RT, we didn't which caused USB issues.
This PR makes it more generic for all background tasks including
USB.
Fixes#5086 and maybe others.
Passing in a PWMOut still works but is deprecated. It will be
removed in CircuitPython 8.0.0
This also switches STM32 timer indices and channel indices to
0-based in our pin data rather than `- 1` everywhere. The latter is
more bug prone.
Most of the way for #3264
Tested on Metro M0, Metro M4, Feather S2, Feather nRF52840, Feather
STM32F4 and Arduino RP2040.
This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
This allows calls to `allocate_memory()` while the VM is running, it will then allocate from the GC heap (unless there is a suitable hole among the supervisor allocations), and when the VM exits and the GC heap is freed, the allocation will be moved to the bottom of the former GC heap and transformed into a proper supervisor allocation. Existing movable allocations will also be moved to defragment the supervisor heap and ensure that the next VM run gets as much memory as possible for the GC heap.
By itself this breaks terminalio because it violates the assumption that supervisor_display_move_memory() still has access to an undisturbed heap to copy the tilegrid from. It will work in many cases, but if you're unlucky you will get garbled terminal contents after exiting from the vm run that created the display. This will be fixed in the following commit, which is separate to simplify review.
This unifies the flash config to the settings used by the Boot ROM.
This makes the config unique per board which allows for changing
quad enable and status bit differences per flash device. It also
allows for timing differences due to the board layout.
This change also tweaks linker layout to leave more ram space for
the CircuitPython heap.
I noticed that this code was referring to samd-specific functionality,
and isn't enabled except in one samd board (pewpew10). Move it.
There is incomplte support for _pew in mimxrt10xx which then caused build
errors; adding a #if guard to check for _pew being enabled fixes it.
The _pew module is not likely to be important on mimxrt but I'll leave the
choice to remove it to someone else.
The iMX RT has a separate wake up controller, the GPC, that replaces
the NVIC when asleep. It adds the ability to only wake up on certain
interrupts. It seems that it requires at least one enabled interrupt
in the NVIC to turn on it's wake up circuitry. It doesn't need to
be the same interrupt as the wake up signal. For example, the RTC
in the SNVS can wake us up if a USB interrupt is enabled. Before
then it won't work. So, we enable the SNVS interrupt on start up
so it can wake us up.
