With mboot encrpytion and fsload enabled, the DEBUG build -O0 compiler
settings result in mboot no longer fitting in the 32k sector. This commit
changes this to -Og which also brings it into line with the regular stm32
build.
MCUs with device-only USB peripherals (eg L0, WB) do not implement (at
least not in the ST HAL) the HAL_PCD_DisconnectCallback event. So if a USB
cable is disconnected the USB driver does not deinitialise itself
(usbd_cdc_deinit is not called) and the CDC driver can stay in the
USBD_CDC_CONNECT_STATE_CONNECTED state. Then if the USB was attached to
the REPL, output can become very slow waiting in usbd_cdc_tx_always for
500ms for each character.
The disconnect event is not implemented on these MCUs but the suspend event
is. And in the situation where the USB cable is disconnected the suspend
event is raised because SOF packets are no longer received.
The issue of very slow output on these MCUs is fixed in this commit (really
worked around) by adding a check in usbd_cdc_tx_always to see if the USB
device state is suspended, and, if so, breaking out of the 500ms wait loop.
This should also help all MCUs for a real USB suspend.
A proper fix for MCUs with device-only USB would be to implement or somehow
synthesise the HAL_PCD_DisconnectCallback event.
See issue #6672.
Signed-off-by: Damien George <damien@micropython.org>
Don't clear the IPCC channel flag until we've actually handled the incoming
data, or else the wireless firmware may clobber the IPCC buffer if more
data arrives. This requires masking the IRQ until the data is handled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's enabled by default to retain the existing behaviour. A board can
disable this option if it manages mounting the filesystem itself, for
example in frozen code.
Signed-off-by: Damien George <damien@micropython.org>
Changes are:
- refactor to use new _create_element function
- support extended version of MOUNT element with block size
- support STATUS element
Signed-off-by: Damien George <damien@micropython.org>
This new element takes the form: (ELEM_TYPE_STATUS, 4, <address>). If this
element is present in the mboot command then mboot will store to the given
address the result of the filesystem firmware update process. The address
can for example be an RTC backup register.
Signed-off-by: Damien George <damien@micropython.org>
Instead it is now passed in as an optional parameter to the ELEM_MOUNT
element, with a compile-time configurable default.
Signed-off-by: Damien George <damien@micropython.org>
The superblock for littlefs is in block 0 and 1, but block 0 may be erased
or partially written, so block 1 must be checked if block 0 does not have a
valid littlefs superblock in it.
Prior to this commit, if block 0 did not contain a valid littlefs
superblock (but block 1 did) then the auto-detection would fail, mounting a
FAT filesystem would also fail, and the system would reformat the flash,
even though it may have contained a valid littlefs filesystem. This is now
fixed.
Signed-off-by: Damien George <damien@micropython.org>
To match the definition of GENERATE_PACK_DFU, so a board can customise the
location/name of this file if needed.
Signed-off-by: Damien George <damien@micropython.org>
To have at least one board configured with MBOOT_ENABLE_PACKING, for CI
testing purposes and demonstration of the feature.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, the final piece of data in a compressed file may have
been lost when decompressing.
Signed-off-by: Damien George <damien@micropython.org>
Mboot builds do not use the external SPI flash in caching mode, and
explicitly disabling it saves RAM and a small bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.
Signed-off-by: Damien George <damien@micropython.org>
When littlefs is enabled extended reading must be supported, and using this
function to read the first block for auto-detection is more efficient (a
smaller read) and does not require a cached SPI-flash read.
Signed-off-by: Damien George <damien@micropython.org>
These functions enable SDRAM data retention in stop mode. Example usage,
in mpconfigboard.h:
#define MICROPY_BOARD_ENTER_STOP sdram_enter_low_power();
#define MICROPY_BOARD_LEAVE_STOP sdram_leave_low_power();
Calculate the bit timing from baudrate if provided, allowing sample point
override. This makes it a lot easier to make CAN work between different
MCUs with different clocks, prescalers etc.
Tested on F4, F7 and H7 Y/V variants.
This much buffer space is required for CDC data out endpoints to avoid any
buffer overflows when the USB CDC is saturated with data.
Signed-off-by: Damien George <damien@micropython.org>
The -Og optimisation level produces a more realistic build, gives a better
debugging experience, and generates smaller code than -O0, allowing debug
builds to fit in flash.
This commit also assigns variables in can.c to prevent warnings when -Og is
used, and builds a board in CI with DEBUG=1 enabled.
Signed-off-by: Damien George <damien@micropython.org>
Allows reserving CAN, I2C, SPI, Timer and UART peripherals. If reserved
the peripheral cannot be accessed from Python.
Signed-off-by: Damien George <damien@micropython.org>
Even though IRQs are disabled this seems to be required on H7 Rev Y,
otherwise Systick interrupt triggers and the MCU leaves the stop mode
immediately.
This commit saves OSCs/PLLs state before STOP mode and restores them on
exit. Some boards use HSI48 for USB for example, others have PLL2/3
enabled, etc.
Also known as L2CAP "connection oriented channels". This provides a
socket-like data transfer mechanism for BLE.
Currently only implemented for NimBLE on STM32 / Unix.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
This fixes the build for non-STM32WB based boards when the NimBLE submodule
has not been fetched, and also allows STM32WB boards to build with BLE
disabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the STM32WB HCI interface (between the two CPUs) to
require the use of MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS, and as a
consequence to require NimBLE. IPCC RX IRQs now schedule the NimBLE
handler to run via mp_sched_schedule.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead. This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.
The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms. When RX IRQ idle events arrive, it will also schedule this
task to improve latency.
There is a similar change for the unix port where the background thread now
queues the scheduled task.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This requires that the event handlers are called from non-interrupt context
(i.e. the MicroPython scheduler).
This will allow the BLE stack (e.g. NimBLE) to run from the scheduler
rather than an IRQ like PENDSV, and therefore be able to invoke Python
callbacks directly/synchronously. This allows writing Python BLE handlers
for events that require immediate response such as _IRQ_READ_REQUEST (which
was previous a hard IRQ) and future events relating to pairing/bonding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
