This commit removes all parts of code associated with the existing
MICROPY_OPT_CACHE_MAP_LOOKUP_IN_BYTECODE optimisation option, including the
-mcache-lookup-bc option to mpy-cross.
This feature originally provided a significant performance boost for Unix,
but wasn't able to be enabled for MCU targets (due to frozen bytecode), and
added significant extra complexity to generating and distributing .mpy
files.
The equivalent performance gain is now provided by the combination of
MICROPY_OPT_LOAD_ATTR_FAST_PATH and MICROPY_OPT_MAP_LOOKUP_CACHE (which has
been enabled on the unix port in the previous commit).
It's hard to provide precise performance numbers, but tests have been run
on a wide variety of architectures (x86-64, ARM Cortex, Aarch64, RISC-V,
xtensa) and they all generally agree on the qualitative improvements seen
by the combination of MICROPY_OPT_LOAD_ATTR_FAST_PATH and
MICROPY_OPT_MAP_LOOKUP_CACHE.
For example, on a "quiet" Linux x64 environment (i3-5010U @ 2.10GHz) the
change from CACHE_MAP_LOOKUP_IN_BYTECODE, to LOAD_ATTR_FAST_PATH combined
with MAP_LOOKUP_CACHE is:
diff of scores (higher is better)
N=2000 M=2000 bccache -> attrmapcache diff diff% (error%)
bm_chaos.py 13742.56 -> 13905.67 : +163.11 = +1.187% (+/-3.75%)
bm_fannkuch.py 60.13 -> 61.34 : +1.21 = +2.012% (+/-2.11%)
bm_fft.py 113083.20 -> 114793.68 : +1710.48 = +1.513% (+/-1.57%)
bm_float.py 256552.80 -> 243908.29 : -12644.51 = -4.929% (+/-1.90%)
bm_hexiom.py 521.93 -> 625.41 : +103.48 = +19.826% (+/-0.40%)
bm_nqueens.py 197544.25 -> 217713.12 : +20168.87 = +10.210% (+/-3.01%)
bm_pidigits.py 8072.98 -> 8198.75 : +125.77 = +1.558% (+/-3.22%)
misc_aes.py 17283.45 -> 16480.52 : -802.93 = -4.646% (+/-0.82%)
misc_mandel.py 99083.99 -> 128939.84 : +29855.85 = +30.132% (+/-5.88%)
misc_pystone.py 83860.10 -> 82592.56 : -1267.54 = -1.511% (+/-2.27%)
misc_raytrace.py 21490.40 -> 22227.23 : +736.83 = +3.429% (+/-1.88%)
This shows that the new optimisations are at least as good as the existing
inline-bytecode-caching, and are sometimes much better (because the new
ones apply caching to a wider variety of map lookups).
The new optimisations can also benefit code generated by the native
emitter, because they apply to the runtime rather than the generated code.
The improvement for the native emitter when LOAD_ATTR_FAST_PATH and
MAP_LOOKUP_CACHE are enabled is (same Linux environment as above):
diff of scores (higher is better)
N=2000 M=2000 native -> nat-attrmapcache diff diff% (error%)
bm_chaos.py 14130.62 -> 15464.68 : +1334.06 = +9.441% (+/-7.11%)
bm_fannkuch.py 74.96 -> 76.16 : +1.20 = +1.601% (+/-1.80%)
bm_fft.py 166682.99 -> 168221.86 : +1538.87 = +0.923% (+/-4.20%)
bm_float.py 233415.23 -> 265524.90 : +32109.67 = +13.756% (+/-2.57%)
bm_hexiom.py 628.59 -> 734.17 : +105.58 = +16.796% (+/-1.39%)
bm_nqueens.py 225418.44 -> 232926.45 : +7508.01 = +3.331% (+/-3.10%)
bm_pidigits.py 6322.00 -> 6379.52 : +57.52 = +0.910% (+/-5.62%)
misc_aes.py 20670.10 -> 27223.18 : +6553.08 = +31.703% (+/-1.56%)
misc_mandel.py 138221.11 -> 152014.01 : +13792.90 = +9.979% (+/-2.46%)
misc_pystone.py 85032.14 -> 105681.44 : +20649.30 = +24.284% (+/-2.25%)
misc_raytrace.py 19800.01 -> 23350.73 : +3550.72 = +17.933% (+/-2.79%)
In summary, compared to MICROPY_OPT_CACHE_MAP_LOOKUP_IN_BYTECODE, the new
MICROPY_OPT_LOAD_ATTR_FAST_PATH and MICROPY_OPT_MAP_LOOKUP_CACHE options:
- are simpler;
- take less code size;
- are faster (generally);
- work with code generated by the native emitter;
- can be used on embedded targets with a small and constant RAM overhead;
- allow the same .mpy bytecode to run on all targets.
See #7680 for further discussion. And see also #7653 for a discussion
about simplifying mpy-cross options.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
- Moves definition of BOARD_FLASH_SIZE and other header files related to
flash configuration into the Makefile.
- Adds board specific clock_config.h.
- Adds board.h, pin_mux.h, and peripherals.h as they are
required by NXP MCU SDK in order to use our own clock_config.h.
- Renames board specific FlexSPI configuration files.
- Updates flash frequency of MIMXRT1020_EVK
- Creates separated flash_config files for QSPI NOR and
QSPI Hyper flash.
- Unifies VFS start address to be @ 1M for 1010 and 1020 boards.
- Unifies 1050EVK boards
- Adds support to both NOR and HyperFlash on boards with
both capabilities.
- Adds automatic FlexRAM initialization to start-up code based on
linker script and NXP HAL.
- Applies code formatting to all files in mimxrt port.
With this change the flash configuration is restructured and
organized. This simplifies the configuration process and
provides a better overview of each board's settings. With the integration
of clock_config.h, board.h, pin_mux.h, and peripherals.h we gain better
control of the settings and clock configurations. Furthermore the
implementation of an explicit FlexRAM setup improves the system
performance and allows for performance tuning.
Signed-off-by: Philipp Ebensberger
This uses a step output from the test job to set the build matrix
for the board build jobs. The built boards depends on which files
were changed.
* Changes contained within ports/*/boards/ will build each board.
* Changes contained within ports/* will build all boards from the
port.
* All other file changes will build all boards.
All boards will be build for pushes in `adafruit/circuitpython` as
well.
A side-effect is that we no longer need to explicitly list the
boards to build. It will automatically update as new folders are
added.
Related to #4009
To keep things neat and tidy, we ensure that each file has 1 and only 1
newline at the end of each file.
Signed-off-by: David Lechner <david@pybricks.com>
This feature {x=} was introduced in Python 3.8 so needs a separate .exp
file to run on earlier Python versions.
See https://bugs.python.org/issue36817
Signed-off-by: Damien George <damien@micropython.org>
This makes it work like --no-follow and --no-exclusive using a mutex group
and dest. Although the current implementation with BooleanOptionAction is
neater it requires Python 3.9, so don't use this feature.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The --no-exclusive flag was accidentally added to the mutex group in
178198a01d.
The --soft-reset flag was accidentally added to the mutex group in
41adf17830.
These flags can be specified independently to --[no-]follow so should not
be in that mutex group.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
And using "-B" means mpy-cross is forcefully rebuilt, sometimes with
invalid CFLAGS_EXTRA options which makes the auto-build fail.
Signed-off-by: Damien George <damien@micropython.org>
The sys.stdin.buffer and sys.stdout.buffer streams work just as well (and
are just as fast) as pyb.USB_VCP on stm32 devices, so there's no need to
have the USB_VCP specialisation code, which just adds complexity.
Also, on stm32 devices with both USB and UART (or other serial interface),
if something other than the USB_VCP port is used for the serial connection
then mpremote mount will not work because it will default to reading and
writing on USB_VCP instead of the other connected serial stream.
As part of this simplification, support for a second port as input is
removed (this feature was never exposed to the user).
Signed-off-by: Damien George <damien@micropython.org>
This implements (most of) the PEP-498 spec for f-strings and is based on
https://github.com/micropython/micropython/pull/4998 by @klardotsh.
It is implemented in the lexer as a syntax translation to `str.format`:
f"{a}" --> "{}".format(a)
It also supports:
f"{a=}" --> "a={}".format(a)
This is done by extracting the arguments into a temporary vstr buffer,
then after the string has been tokenized, the lexer input queue is saved
and the contents of the temporary vstr buffer are injected into the lexer
instead.
There are four main limitations:
- raw f-strings (`fr` or `rf` prefixes) are not supported and will raise
`SyntaxError: raw f-strings are not supported`.
- literal concatenation of f-strings with adjacent strings will fail
"{}" f"{a}" --> "{}{}".format(a) (str.format will incorrectly use
the braces from the non-f-string)
f"{a}" f"{a}" --> "{}".format(a) "{}".format(a) (cannot concatenate)
- PEP-498 requires the full parser to understand the interpolated
argument, however because this entirely runs in the lexer it cannot
resolve nested braces in expressions like
f"{'}'}"
- The !r, !s, and !a conversions are not supported.
Includes tests and cpydiffs.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Call `supervisor.disable_ble_workflow()` and the BLE workflow will
be disabled until the chip is reset.
This also includes a couple fixes:
1. Terminals can now be deinit by setting the tilegrid to NULL. This
prevents using the tilegrid before display is init.
2. Fix BLE serial send amount when sending more than a single packet.
Fixes#5049
@dhalbert noticed that if a fork was called `micropython`, the
existing check could fail during CI because it will be cloned into a
directory also called `micropython`.
Instead of hardcoding a range of strings that are OK as top directories,
find the location of the top directory relative to the script.
This will be conflicty after #5069 is merged, but it should be easy to
fix.
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.
The Makefile had to be changed in order to build the .bin file as well.
Coverage calculated by Codecov has the same reliability/deterministic
issues as Coveralls did, so the problem is likely to do with the output of
lcov/gcov, rather than the analysis and display of the data.
Switch from lcov to gcov for data generation to try and simplify this
process of computing coverage.
Signed-off-by: Damien George <damien@micropython.org>
* so that excess files are not included in sdist, perform build down
in circuitpython-stubs
* This means we need to
* Remove the need-pypi check
* Copy a setup.py, README, and MANIFEST.in into the stubs build location
* Revamp how the overall `mypy --strict` check lists its inputs
* Add a new test that actually installing the stubs lets us do type
checking (tools/test-stubs.sh)
* Add a missing return type to a __init__ function (why was this not
an error under `mypy --strict`, I wonder)
Now a ctrl-C will not stop mpremote, rather this character will be passed
through to the attached device.
The mpremote version is also increased to 0.0.5.
Signed-off-by: Damien George <damien@micropython.org>
Using just the list of available ports, instead of a hard-coded list of
possible ports, means that all ports will be available for auto connection.
And the order that they will be attempted in will match what's printed by
"mpremote connect list" (and will be the same as before, trying ACMx before
USBx). Auto-connect will also now work on Mac, and will allow all COM
ports on Windows.
Signed-off-by: Damien George <damien@micropython.org>
.. this board is nearly the same as the "1.2" version originally
released, but makes a few changes to reduce pin conflicts between the 13-pin
camera header and the bootstrapping pins. "1.3" was introduced in summer
2020-- check the bottom of your board silk to find out whether you have a 1.2
or a 1.3, because it's not clear whether there is remaining 1.2 stock.
Another vexing fact about the 1.3 is that its LCD can have one of two
chipets, and the chipset used is not marked anywhere!
Following on from ef16834887, this adds a
coverage build and running of the test suite on an ARM 32-bit Linux-based
architecture.
Signed-off-by: Damien George <damien@micropython.org>
This adds a coverage build and running of the test suite on a MIPS 32-bit
big endian architecture. It uses the feature of qemu to execute foreign
code as though it were native to the system (using qemu user mode). The
code compiled for MIPS will run under the qemu VM, but all syscalls made by
this code go to the host (Linux) system.
See related #7268 and #7273.
Signed-off-by: Damien George <damien@micropython.org>
As the new default behaviour, this allows PyDFU to be used with all
devices, not just the ones matching a specific set of VID/PID values. But
it's still possible to specify VID/PID if needed to narrow down the
selection of the USB device.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
This can be treated by the linker the same as R_X86_64_REX_GOTPCRELX,
according to https://reviews.llvm.org/D18301.
Signed-off-by: Damien George <damien@micropython.org>
* modframebuf: _mp_framebuf_p_t is not "really" a protocol, but the
QSTR assignment caused problems when building as a dynamic module
* modure: str_index_to_ptr is not in the natmod API, disable URE match
spans when dynamic. mp_obj_len() is a bugfix, we should throw here
if the object is not string-like
* moduzlib: Correct paths to uzlib headers & sources. this relative
path (from moduzlib.c to the referenced file) works in all cases,
the other only worked from ports/PORTNAME.
* dynruntime: Handle 2-arg m_malloc, assert_native_inited, add a
micropythonish mp_arg_check_num_mp, fix mp_raise_msg to use dumb
strings, add mp_raise_arg1
* nativeglue: ad assert_native_inited
* translate: MP_ERROR_TEXT evaluates to its argument for DYNRUNTIME
* mpy-tool: A straggling magic number change
* mpy_ld: Have to renumber manually after dynruntime change
* import_mpy_native_gc.py: Update copy of features0 baked into this test
After discussing with danh, I noticed that `a/**/b` would not match `a/b`.
After correcting this and re-running "pre-commit run --all", additional
files were reindented, including the codeformat script itself.
In #4683, tannewt noticed that uncrustify was not running on some
file in common-hal.
I investigated and found that it was not being run on a bunch of paths.
Rather than make incremental changes, I rewrote list_files to work
bsaed on regular expressions; these regular expressions are created from
the same git-style glob patterns.
I spot-checked some specific filenames after this change, and all looks good:
```
$ python3 tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup extmod/virtpin.c ports/raspberrypi/background.h ports/raspberrypi/common-hal/pulseio/PulseIn.c
black --fast --line-length=99 -v tests/thread/thread_exit1.py
```
recursiveloop and int_small are excluded, while PulseIn, virtpin,
and background are included.
Testing running from a subdirectory (not _specifically_ supported though):
```
(cd ports && python3 ../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c)
../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup ../extmod/virtpin.c raspberrypi/common-hal/pulseio/PulseIn.
```
As a side-effect, a bunch more files are re-formatted now. :-P
Since version 21.4b0, Black now processes one-line docstrings by stripping
leading and trailing spaces, and adding a padding space when needed to
break up """"; see https://github.com/psf/black/pull/1740
This commit makes the Python code in this repository conform to this rule.
This is now the default, but can be overridden with CLI `--no-exclusive`,
or constructing `Pyboard(..., exclusive=False)`.
Signed-off-by: Damien George <damien@micropython.org>
This allows the compiler to merge strings: e.g. "update",
"difference_update" and "symmetric_difference_update"
will all point to the same memory.
Shaves ~1KB off the image size, and potentially allows
bigger savings if qstr attrs are initialized in qstr_init(),
and not stored in the image.
It's a bit of a pitfall with user C modules that including them in the
build does not automatically enable them. This commit changes the docs and
examples for user C modules to encourage writers of user C modules to
enable them unconditionally. This makes things simpler and covers most use
cases.
See discussion in issue #6960, and also #7086.
Signed-off-by: Damien George <damien@micropython.org>
When running from pre-commit, we believe the different invocations of
sed were racing with each other, sometimes leaving zero-byte files in
the filesystem (ow)
