nRF CircuitPython boards will now provide the file transfer
service defined here: https://github.com/adafruit/Adafruit_CircuitPython_BLE_File_Transfer
USB capable boards will only advertise if previously bonded to a
device or if the reset button is pressed during the fast blue
flashes on start up. When pressed, the board will restart again but
the blue period will not flash.
Boards without USB will always advertise.
When previously bonded, the advertisement is private so that no
other peers can connect. If advertising publicly, the tx power is
lowered to reduce the likelihood of bonding from a distance.
This PR also fixes issues with loading identities of bonded peers
so that our address can now be resolved and we can resolve others'
addresses when scanning.
This also removes the need to pin share because we don't use the
status LED while user code is running.
The status flashes fallback to the HW_STATUS LED if no RGB LED is
present. Each status has a unique blink pattern as well.
One caveat is the REPL state. In order to not pin share, we set the
RGB color once. PWM and single color will be shutoff immediately but
DotStars and NeoPixels will hold the color until the user overrides
it.
Fixes#4133
Unify USB-related makefile var and C def as CIRCUITPY_USB.
Always define it as 0 or 1, same as all other settings.
USB_AVAILABLE was conditionally defined in supervisor.mk,
but never actually used to #ifdef USB-related code.
Loosely related to #4546
The interrupt may have a higher priority than the serial output's
(USB) interrupt and may never make room. This makes prints from
interrupts (like the BLE event calls) best effort for what can be
queued up. The rest of the output will be dropped.
This switches stage2 to C and uses Jinja to change the C code based
on flash settings from https://github.com/adafruit/nvm.toml. It
produces the fastest settings for the given set of external flashes.
Flash size is no longer hard coded so switching flashes with similar
capabilities but different sizes should *just work*.
This PR also places "ITCM" code in RAM to save the XIP cache for
code execution. Further optimization is possible. A blink code.py
still requires a number of flash fetches every blink.
Fixes#4041
Instead of counting words in make, which is slightly awful, notice that
possible_devices is local to external_flash.c, so we can declare the array
with an automatic bound, and then get the count as the element-count
(MP_ARRAY_SIZE) of the array.
Since EXTERNAL_FLASH_DEVICE_COUNT is no longer a global macro, switch
a few sites to using EXTERNAL_FLASH_DEVICES in `#if` checks instead.
.. however, the number of endpoints is only set for SAMD (8).
Other ports need to set the value. Otherwise, the build will show
the message
```
Unable to check whether maximum number of endpoints is respected
```
The font is missing many characters and the build needs the space.
We can optimize font storage when we get a good font.
The serial output will work as usual.
In time, we should transition interrupt driven background tasks out of the
overall run_background_tasks into distinct background callbacks,
so that the number of checks that occur with each tick is reduced.
This restores the ability to remove CDC and/or MSC, at the price of
giving up the new automatic check that USB_DEVICES is correct.
Since devices have to have CDC and MSC to be "CircuitPython",
this is not a facility that is going to be used by any in-tree drivers.
Since Actions passed on the previous commit, where this computed value
was checked against the specified value (if any), this is no net change,
except that we no longer need to specify it for particular boards or
ports.
This code is shared by most parts, except where not all the #ifdefs
inside the tick function were present in all ports. This mostly would
have broken gamepad tick support on non-samd ports.
The "ms32" and "ms64" variants of the tick functions are introduced
because there is no 64-bit atomic read. Disabling interrupts avoids
a low probability bug where milliseconds could be off by ~49.5 days
once every ~49.5 days (2^32 ms).
Avoiding disabling interrupts when only the low 32 bits are needed is a minor
optimization.
Testing performed: on metro m4 express, USB still works and
time.monotonic_ns() still counts up
In cases where more than one board is connected to a single computer it can become pretty hard to figure out which board you're actually talking to. For example, if you have several MIDI-compatible boards they all show up as "CircuitPython MIDI". This change allows boards to replace the "CircuitPython" part of their USB descriptors with more specific text, for example, "CircuitPython Feather" or just "Feather". This will let folks more easily tell boards apart.
The new option is named `USB_INTERFACE_NAME` and is available in `mkconfigboard.mk`. For example:
```
USB_INTERFACE_NAME = "Feather"
```
This PR refines the _bleio API. It was originally motivated by
the addition of a new CircuitPython service that enables reading
and modifying files on the device. Moving the BLE lifecycle outside
of the VM motivated a number of changes to remove heap allocations
in some APIs.
It also motivated unifying connection initiation to the Adapter class
rather than the Central and Peripheral classes which have been removed.
Adapter now handles the GAP portion of BLE including advertising, which
has moved but is largely unchanged, and scanning, which has been enhanced
to return an iterator of filtered results.
Once a connection is created (either by us (aka Central) or a remote
device (aka Peripheral)) it is represented by a new Connection class.
This class knows the current connection state and can discover and
instantiate remote Services along with their Characteristics and
Descriptors.
Relates to #586
