Also restrict higher frequencies to have a VCO_OUT frequency below
432MHz, as specified in the datasheet.
Docs improved to list allowed frequencies, and explain about USB
stability.
This is experimental support. API is subject to changes. RTS/CTS
available on UART(2) and UART(3) only. Use as:
uart = pyb.UART(2, 9600, flow=pyb.UART.RTS | pyb.UART.CTS)
This patch also enables non-blocking streams on stmhal port.
One can now make a USB-UART pass-through function:
def pass_through(usb, uart):
while True:
select.select([usb, uart], [], [])
if usb.any():
uart.write(usb.read(256))
if uart.any():
usb.write(uart.read(256))
pass_through(pyb.USB_VCP(), pyb.UART(1, 9600))
Improvements are:
2 ctrl-C's are now needed to truly kill running script on pyboard, so
make CDC interface allow multiple ctrl-C's through at once (ie sending
b'\x03\x03' to pyboard now counts as 2 ctrl-C's).
ctrl-C in friendly-repl can now stop multi-line input.
In raw-repl mode, use ctrl-D to indicate end of running script, and also
end of any error message. Thus, output of raw-repl is always at least 2
ctrl-D's and it's much easier to parse.
pyboard.py is now a bit faster, handles exceptions from pyboard better
(prints them and exits with exit code 1), prints out the pyboard output
while the script is running (instead of waiting till the end), and
allows to follow the output of a previous script when run with no
arguments.
This allows to implement KeyboardInterrupt on unix, and a much safer
ctrl-C in stmhal port. First ctrl-C is a soft one, with hope that VM
will notice it; second ctrl-C is a hard one that kills anything (for
both unix and stmhal).
One needs to check for a pending exception in the VM only for jump
opcodes. Others can't produce an infinite loop (infinite recursion is
caught by stack check).
TIM2_CH1_ETR is really bundling 2 functions to the same pin:
TIM2_CH1 (where its used as a channel)
TIM2_ETR (where iss used as an external trigger).
I fixed most of these a while back, but it looks like I missed this one.
Also make cc3k.send and cc3k.recv independent functions (not wrapped by
stream write/read). Also make wiznet5k.recv more memory efficient.
This might address issue #920.
UART object now uses a stream-like interface: read, readall, readline,
readinto, readchar, write, writechar.
Timeouts are configured when the UART object is initialised, using
timeout and timeout_char keyword args.
The object includes optional read buffering, using interrupts. You can set
the buffer size dynamically using read_buf_len keyword arg. A size of 0
disables buffering.
This makes open() and _io.FileIO() more CPython compliant.
The mode kwarg is fully iplemented.
The encoding kwarg is allowed but not implemented; mainly to allow
the tests to specify encoding for CPython, see #874
When loading the ELF binary to the board with a debugger, the debugger
needs to know at which point to start executing the code. Currently the
entry point defaults to the start of the .text section.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
This fixed an issue with a certain SD card sometimes not initialising
first time round. See issue #822 for related, and thanks to
@iabdalkader for the idea.
Also, usocket.readinto(). Known issue is that .readinto() should be available
only for binary files, but micropython uses single method table for both
binary and text files.
os, time, select modules are now prefixed with u, but are still
available (via weak links) as their original names.
ure and ujson now available as re and json via weak links.
This patch enables output on the complimentary channels (TIMx_CHyN).
For timers 1 and 8, deadtime can also be inserted when the channels
transition. For the pyboard, TIM8_CH1/CH1N and TIM8_CH2/CH2N can
take advantage of this.
Found these by compiling stmhal with mp_uint_t of type uint32_t instead
of unsigned int. This actually makes a difference to the code, but just
a curiosity.
Timers now have the following new features:
- can init freq using floating point; eg tim.init(freq=0.1)
- tim.source_freq() added to get freq of timer clock source
- tim.freq() added to get/set freq
- print(tim) now prints freq
Eg pyb.freq(120000000) sets the CPU to 120MHz. The frequency can be set
at any point in the code, and can be changed as many times as you like.
Note that any active timers will need to be reconfigured after a freq
change.
Valid range is 24MHz to 168MHz (but not all freqs are supported). The
code maintains a 48MHz clock for the USB at all times and it's possible
to change the frequency at a USB REPL and keep the REPL alive (well,
most of the time it stays, sometimes it resets the USB for some reason).
Note that USB does not work with pyb.freq of 24MHz.
Remove reference to pyb.gc; add reference to pyb.millis.
There are lots of functions not listed when you run help(), but it would
be too much to list them all, so we list only some basic, useful ones.
Addresses issue #846.
As per issue #876, the network module is used to configure NICs
(hardware modules) and configure routing. The usocket module is
supposed to implement the normal Python socket module and selects the
underlying NIC using routing logic.
Right now the routing logic is brain dead: first-initialised,
first-used. And the routing table is just a list of registered NICs.
cc3k and wiznet5k work, but not at the same time due to C name clashes
(to be fixed).
Note that the usocket module has alias socket, so that one can import
socket and it works as normal. But you can also override socket with
your own module, using usocket at the backend.
In CPython IOError (and EnvironmentError) is deprecated and aliased to
OSError. All modules that used to raise IOError now raise OSError (or a
derived exception).
In Micro Python we never used IOError (except 1 place, incorrectly) and
so don't need to keep it.
See http://legacy.python.org/dev/peps/pep-3151/ for background.
Teensy doesn't need to worry about overflows since all of
its timers are only 16-bit.
For PWM, the pulse width needs to be able to vary from 0..period+1
(pulse-width == period+1 corresponds to 100% PWM)
I couldn't test the 0xffffffff cases since we can't currently get a
period that big in python. With a prescaler of 0, that corresponds
to a freq of 0.039 (i.e. cycle every 25.56 seconds), and we can't
set that using freq or period.
I also tested both stmhal and teensy with floats disabled, which
required a few other code changes to compile.
Pulled in and modified work done by mux/iabdalkader on cc3k driver, from
iabdalkader-cc3k-update branch. That branch was terribly messy and had
too many conflicts to merge neatly.
Fix stmhal and teensy print routines to report actual prescaler an period.
Fix teensy build to use soft-float
Add USE_ARDUINO_TOOLCHAIN option to teensy build
mp_parse_node_free now frees the memory associated with non-interned
strings. And the parser calls mp_parse_node_free when discarding a
non-used node (such as a doc string).
Also, the compiler now frees the parse tree explicitly just before it
exits (as opposed to relying on the caller to do this).
Addresses issue #708 as best we can.
Stack is full descending and must be 8-byte aligned. It must start off
pointing to just above the last byte of RAM.
Previously, stack started pointed to last byte of RAM (eg 0x2001ffff)
and so was not 8-byte aligned. This caused a bug in combination with
alloca.
This patch also updates some debug printing code.
Addresses issue #872 (among many other undiscovered issues).
This allows to set the pulse width (for PWM mode) as a ratio relative to
the period of the timer. Eg, 0.5 is a 50% duty cycle. You can set the
ratio in the channel init, or using channel.pulse_width_ratio; the
latter can also read the pulse width as a ratio.
By measuring SD card addresses in blocks and not bytes, one can get away
with using 32-bit numbers.
This patch also uses proper atomic lock/unlock around SD card
read/write, adds SD.info() function, and gives error code for failed
read/writes.
sys.exit always raises SystemExit so doesn't need a special
implementation for each port. If C exit() is really needed, use the
standard os._exit function.
Also initialise mp_sys_path and mp_sys_argv in teensy port.
Allows to create socket objects that support TCP and UDP in server and
client mode. Interface is very close to standard Python socket class,
except bind and accept do not work the same (due to hardware not
supporting them in the usual way).
Not compiled by default. To compile this module, use:
make MICROPY_PY_WIZNET5K=1
Top-level lib directory is for standard C libraries that we want to
provide our own versions of (for efficiency and stand-alone reasons).
It currently has libm in it for math functions.
Also add atanf and atan2f, which addresses issue #837.
SysTick IRQ now increases millisecond counter directly (ie without
calling HAL_IncTick). Provide our own version of HAL_Delay that does a
wfi while waiting. This more than halves power consumption when running
a loop containing a pyb.delay call. It used to be like this, but new
version of HAL library regressed this feature.
I also removed trailing spaces from modpyb.c which affected a couple
of lines technically not part of this patch.
Tested using: https://github.com/dhylands/upy-examples/blob/master/micros_test.py
which eventually fails due to wraparound issues (I could fix the test to compensate
but didn't bother)
These functions are generally 1 machine instruction, and are used in
critical code, so makes sense to have them inline.
Also leave these functions uninverted (ie 0 means enable, 1 means
disable) and provide macro constants if you really need to distinguish
the states. This makes for smaller code as well (combined with
inlining).
Applied to teensy port as well.
Because (for Thumb) a function pointer has the LSB set, pointers to
dynamic functions in RAM (eg native, viper or asm functions) were not
being traced by the GC. This patch is a comprehensive fix for this.
Addresses issue #820.
It's still "safe" because no scripts are run. Remove the SD card if you
want to access the internal flash filesystem. Addresses issue #616.
Also: remove obsolete pyb.source_dir setting, and reset pyb.main and
pyb.usb_mode settings on soft-reset.
Converts generted pins to use qstrs instead of string pointers.
This patch also adds the following functions:
pyb.Pin.names()
pyb.Pin.af_list()
pyb.Pin.gpio()
dir(pyb.Pin.board) and dir(pyb.Pin.cpu) also produce useful results.
pyb.Pin now takes kw args.
pyb.Pin.__str__ now prints more useful information about the pin
configuration.
I found the following functions in my boot.py to be useful:
```python
def pins():
for pin_name in dir(pyb.Pin.board):
pin = pyb.Pin(pin_name)
print('{:10s} {:s}'.format(pin_name, str(pin)))
def af():
for pin_name in dir(pyb.Pin.board):
pin = pyb.Pin(pin_name)
print('{:10s} {:s}'.format(pin_name, str(pin.af_list())))
```
This patch updates ST's HAL to the latest version, V1.3.0, dated 19 June
2014. Files were copied verbatim from the ST package. Only change was
to suppress compiler warning of unused variables in 4 places.
A lot of the changes from ST are cosmetic: comments and white space.
Some small code changes here and there, and addition of F411 header.
Main code change is how SysTick interrupt is set: it now has a
configuration variable to set the priority, so we no longer need to work
around this (originall in system_stm32f4xx.c).
Make a clearer distinction between init functions that must be done
before any scripts can run (xxx_init0) and those that can be safely
deferred (xxx_init).
Fix bug initialising USB VCP exception. Addresses issue #788.
Re-order some init function to improve reliability of
reset/soft-reset.
Damien George
Sven Wegener
Henrik Sölver
stijn
Felix Domke
Dave Hylands
Paul Sokolovsky
iabdalkader
Hirotaka Kawata
David Siorpaes