Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
The ADC_FIRST_GPIO_CHANNEL and ADC_LAST_GPIO_CHANNEL macros are no longer
needed. Instead the pin_adcX table (X = 1, 2, 3) is now generated to be
the exact size needed for a given MCU, and MP_ARRAY_SIZE(pin_adcX) is used
to determine the upper bound.
This commit also allows CPU pins to be excluded from ADC configuration if
they are hidden by prefixing their name with a "-".
Signed-off-by: Damien George <damien@micropython.org>
With GCC 11 there is now a warning about array bounds of OTP-mac, due to
the OTP being a literal address.
Signed-off-by: Damien George <damien@micropython.org>
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.
Signed-off-by: Alexander Ziubin aziubin@googlemail.com
Support for C++ was added in 97960dc7de but
that commit didn't include the C++ exception handling table in the binary
firmware image. This commit fixes that.
Signed-off-by: Damien George <damien@micropython.org>
Add LPUART1 as a standard UART. No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:
STM32WB: LPUART1 = UART(2)
STM32L0: LPUART1 = UART(6)
STM32L4: LPUART1 = UART(6)
STM32H7: LPUART1 = UART(9)
On all ports: LPUART1 = machine.UART('LP1')
LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.
Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
This allows changing the baudrate of the UART without reinitialising it
(reinitialising can lead to spurious characters sent on the TX line).
Signed-off-by: Damien George <damien@micropython.org>
This new element takes the form: (ELEM_TYPE_STATUS, 4, <address>). If this
element is present in the mboot command then mboot will store to the given
address the result of the filesystem firmware update process. The address
can for example be an RTC backup register.
Signed-off-by: Damien George <damien@micropython.org>
To have at least one board configured with MBOOT_ENABLE_PACKING, for CI
testing purposes and demonstration of the feature.
Signed-off-by: Damien George <damien@micropython.org>
Mboot builds do not use the external SPI flash in caching mode, and
explicitly disabling it saves RAM and a small bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.
Signed-off-by: Damien George <damien@micropython.org>
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.
This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised. It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.
Signed-off-by: Damien George <damien@micropython.org>
When installing WS firmware, the very first GET_STATE can take several
seconds to respond (especially with the larger binaries like
BLE_stack_full).
Allows stm.rfcore_sys_hci to take an optional timeout, defaulting to
SYS_ACK_TIMEOUT_MS (which is 250ms).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The flash can sometimes be in an already-unlocked state, and attempting to
unlock it again will cause an immediate reset. So make _Flash.unlock()
check FLASH_CR_LOCK to get the current state.
Also fix some magic numbers for FLASH_CR_LOCK AND FLASH_CR_STRT.
The machine.reset() could be removed because it no longer crashes now that
the flash unlock is fixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a script that can be run on-device to install FUS and WS
binaries from the filesystem. Instructions for use are provided in
the rfcore_firmware.py file.
The commit also removes unneeded functionality from the existing rfcore.py
debug script (and renames it rfcore_debug.py).
The device info table has a different layout when core 2 is in FUS mode.
In particular it's larger than the 32 bytes used when in WS mode and if the
correct amount of space is not allocated then the end of the table may be
overwritten with other data (eg with FUS version 0.5.3). So update the
structure to fix this.
Also update rfcore.py to disable IRQs (which are enabled by rfcore.c), to
not depend on uctypes, and to not require the asm_thumb emitter.
Signed-off-by: Damien George <damien@micropython.org>
This allows prototyping rfcore.c improvements from Python.
This was mostly written by @dpgeorge with small modifications to work after
rfcore_init() by @jimmo.
- Split tables and buffers into SRAM2A/2B.
- Use structs rather than word offsets to access tables.
- Use FLASH_IPCCDBA register value rather than option bytes directly.
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
Mboot now supports FAT, LFS1 and LFS2 filesystems, to load firmware from.
The filesystem needed by the board must be explicitly enabled by the
configuration variables MBOOT_VFS_FAT, MBOOT_VFS_LFS1 and MBOOT_VFS_LFS2.
Boards that previously used FAT implicitly (with MBOOT_FSLOAD enabled) must
now add the following config to mpconfigboard.h:
#define MBOOT_VFS_FAT (1)
Signed-off-by: Damien George <damien@micropython.org>
