This patch adds support to mboot for programming external SPI flash. It
allows SPI flash to be programmed via a USB DFU utility in the same way
that internal MCU flash is programmed.
Prior to this patch the QSPI driver assumed that the length of all data
reads and writes was a multiple of 4. This patch allows any length. Reads
are optimised for speed by using 32-bit transfers when possible, but writes
always use a byte transfer because they only use a single data IO line and
are relatively slow.
The DMA peripheral is limited to transferring 65535 elements at a time so
in order to send more than that the SPI driver must split the transfers up.
The user must be aware of this limit if they are relying on precise timing
of the entire SPI transfer, because there might be a small delay between
the split transfers.
Fixes issue #3851, and thanks to @kwagyeman for the original fix.
If the user button is held down indefinitely (eg unintenionally, or because
the GPIO signal of the user button is connected to some external device)
then it makes sense to end the reset mode cycle with the default mode of
1, which executes code as normal.
It's possible (at least on F4 MCU's) to have RXNE and STOPF set at the same
time during a call to the slave IRQ handler. In such cases RXNE should be
handled before STOPF so that all bytes are processed before
i2c_slave_process_rx_end() is called.
Due to buffering of outgoing bytes on the I2C bus, detection of a NACK
using the ISR_NACKF flag needs to account for the case where ISR_NACKF
corresponds to the previous-to-previous byte.
This patch renames the existing SPI flash API functions to reflect the fact
that the go through the cache:
mp_spiflash_flush -> mp_spiflash_cache_flush
mp_spiflash_read -> mp_spiflash_cached_read
mp_spiflash_write -> mp_spiflash_cached_write
The DFU USB config descriptor returns 0x0800=2048 for the supported
transfer size, and this applies to both TX (IN) and RX (OUT). So increase
the rx_buf to support this size without having a buffer overflow on
received data.
With this patch mboot in USB DFU mode now works with dfu-util.
MICROPY_PY_DELATTR_SETATTR can now be enabled without a performance hit for
classes that don't use this feature.
MICROPY_PY_BUILTINS_NOTIMPLEMENTED is a minor addition that improves
compatibility with CPython.
They are now efficient (in runtime performance) and provide a useful
feature that's hard to obtain without them enabled.
See issue #3644 and PR #3826 for background.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
It should be up to the NIC itself to decide if the network interface is
removed upon soft reset. Some NICs can keep the interface up over a soft
reset, which improves usability of the network.
Pins with multiple alt-funcs for the same peripheral (eg USART_CTS_NSS)
need to be split into individual alt-funcs for make-pins.py to work
correctly.
This patch changes the following:
- Split `..._CTS_NSS` into `..._CTS/..._NSS`
- Split `..._RTS_DE` into `..._RTS/..._DE`
- Split `JTDO_SWO` into `JTDO/TRACESWO` for consistency
- Fixed `TRACECK` to `TRACECLK` for consistency
If no block devices are defined by a board then storage support will be
disabled. This means there is no filesystem provided by either the
internal flash or external SPI flash. But the VFS system can still be
enabled and filesystems provided on external devices like an SD card.
Mboot is a custom bootloader for STM32 MCUs. It can provide a USB DFU
interface on either the FS or HS peripherals, as well as a custom I2C
bootloader interface.
These files provide no additional information, all the version and license
information is captured in the relevant files in these subdirectories.
Thanks to @JoeSc for the original patch.
This patch allows to use lwIP as the implementation of the usocket module,
instead of the existing socket-multiplexer that delegates the entire TCP/IP
layer to the NIC itself.
This is disabled by default, and enabled by defining MICROPY_PY_LWIP to 1.
When enabled, the lwIP TCP/IP stack will be included in the build with
default settings for memory usage and performance (see
lwip_inc/lwipopts.h). It is then up to a particular NIC to register itself
with lwIP using the standard lwIP netif API.
Dan Halbert
Damien George
rolandvs
Tobias Badertscher