djsundog/circuitpython
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
5ee1cb2771
circuitpython/ports/stm32/boards/HYDRABUS/mpconfigboard.h

75 lines
2.7 KiB
C
Raw Normal View History

micropython port for HydraBus
2014-06-02 15:43:02 -04:00
#define MICROPY_HW_BOARD_NAME "HydraBus1.0"
Change MCU name config micro
2014-06-26 18:35:53 -04:00
#define MICROPY_HW_MCU_NAME "STM32F4"
micropython port for HydraBus
2014-06-02 15:43:02 -04:00
#define MICROPY_HW_HAS_SWITCH (1)
stmhal/diskio: Introduce MICROPY_HW_HAS_FLASH setting. To allow to reuse stmhal/diskio for ports which don't have flash but have other storage devices.
2016-02-06 07:48:58 -05:00
#define MICROPY_HW_HAS_FLASH (1)
micropython port for HydraBus
2014-06-02 15:43:02 -04:00
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_DAC (1)
stm32/boards: Update all boards to work with new USB configuration.
2018-02-13 02:57:01 -05:00
#define MICROPY_HW_ENABLE_USB (1)
stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD. For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 00:21:26 -04:00
#define MICROPY_HW_ENABLE_SDCARD (1)
micropython port for HydraBus
2014-06-02 15:43:02 -04:00
stmhal: Make HSE PLL parameters configurable per board.
2015-04-18 10:30:04 -04:00
// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
stmhal: Allow to configure UART pins completely via mpconfigboard.h.
2015-05-02 12:31:39 -04:00
// UART config
stmhal: Refactor UART configuration to use pin objects. This follows the pattern of other peripherals (I2C, SPI) to specify the pins using pin objects instead of a pair of GPIO port and pin number. It makes it easier to customise the UART pins for a particular board.
2016-12-04 20:21:45 -05:00
#define MICROPY_HW_UART1_TX (pin_A9)
#define MICROPY_HW_UART1_RX (pin_A10)
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART2_RTS (pin_A1)
#define MICROPY_HW_UART2_CTS (pin_A0)
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
#define MICROPY_HW_UART3_RTS (pin_D12)
#define MICROPY_HW_UART3_CTS (pin_D11)
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
stmhal: Allow to configure UART pins completely via mpconfigboard.h.
2015-05-02 12:31:39 -04:00
all: Replace busses with buses. "buses" is the widely accepted plural form of "bus".
2021-05-20 02:21:47 -04:00
// I2C buses
stmhal: Make I2C busses and their pins configurable in mpconfigboard.h.
2015-04-18 11:12:57 -04:00
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
all: Replace busses with buses. "buses" is the widely accepted plural form of "bus".
2021-05-20 02:21:47 -04:00
// SPI buses
stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx. Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured.
2015-12-12 10:02:02 -05:00
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS (pin_B12)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
#define MICROPY_HW_SPI3_NSS (pin_A4)
#define MICROPY_HW_SPI3_SCK (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)
micropython port for HydraBus
2014-06-02 15:43:02 -04:00
// USRSW/UBTN (Needs Jumper UBTN) is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_A0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// The HydraBus has 1 LED (Needs jumper on ULED)
#define MICROPY_HW_LED1 (pin_A4) // green
#define MICROPY_HW_LED2 (pin_A4) // same as LED1
#define MICROPY_HW_LED3 (pin_A4) // same as LED1
#define MICROPY_HW_LED4 (pin_A4) // same as LED1
stmhal/led: Refactor LED to use mp_hal_pin_output() init function. As part of this patch the MICROPY_HW_LED_OTYPE setting is removed because it is now unused (all boards anyway had this as OUTPUT_PP).
2016-10-17 23:43:05 -04:00
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
micropython port for HydraBus
2014-06-02 15:43:02 -04:00
// SD card detect switch (not used, always on)
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)
stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards. This config option is for the USB OTG pin, pin A10. This is used on some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it shouldn't be used for OTG ID (actually PA10 is multiplexed on this board, but defaults to LED(2)). Partially addresses issue #1059.
2015-01-12 11:13:29 -05:00
// USB config
stm32/boards: Update all boards to work with new USB configuration.
2018-02-13 02:57:01 -05:00
#define MICROPY_HW_USB_FS (1)
stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards. This config option is for the USB OTG pin, pin A10. This is used on some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it shouldn't be used for OTG ID (actually PA10 is multiplexed on this board, but defaults to LED(2)). Partially addresses issue #1059.
2015-01-12 11:13:29 -05:00
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
Reference in New Issue Copy Permalink