circuitpython/stmhal/boards/HYDRABUS/mpconfigboard.h

#define HYDRABUSV10

#define MICROPY_HW_BOARD_NAME       "HydraBus1.0"
#define MICROPY_HW_MCU_NAME         "STM32F4"

#define MICROPY_HW_HAS_SWITCH       (1)
#define MICROPY_HW_HAS_SDCARD       (1)
#define MICROPY_HW_HAS_MMA7660      (0)
#define MICROPY_HW_HAS_LIS3DSH      (0)
#define MICROPY_HW_HAS_LCD          (0)
#define MICROPY_HW_ENABLE_RNG       (1)
#define MICROPY_HW_ENABLE_RTC       (0)
#define MICROPY_HW_ENABLE_TIMER     (1)
#define MICROPY_HW_ENABLE_SERVO     (0)
#define MICROPY_HW_ENABLE_DAC       (1)
#define MICROPY_HW_ENABLE_CAN       (0)

// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)

// UART config
#define MICROPY_HW_UART1_PORT (GPIOA)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 | GPIO_PIN_10)
#define MICROPY_HW_UART2_PORT (GPIOA)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
#define MICROPY_HW_UART2_RTS  (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS  (GPIO_PIN_0)
#define MICROPY_HW_UART3_PORT (GPIOD)
#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 | GPIO_PIN_9)
#define MICROPY_HW_UART3_RTS  (GPIO_PIN_12)
#define MICROPY_HW_UART3_CTS  (GPIO_PIN_11)
#define MICROPY_HW_UART4_PORT (GPIOA)
#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
#define MICROPY_HW_UART6_PORT (GPIOC)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)

// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)

// SPI busses
#define MICROPY_HW_SPI1_NSS  (pin_A4)
#define MICROPY_HW_SPI1_SCK  (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS  (pin_B12)
#define MICROPY_HW_SPI2_SCK  (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
#define MICROPY_HW_SPI3_NSS  (pin_A4)
#define MICROPY_HW_SPI3_SCK  (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)

// USRSW/UBTN (Needs Jumper UBTN) is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN        (pin_A0)
#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED    (1)

// The HydraBus has 1 LED (Needs jumper on ULED)
#define MICROPY_HW_LED1             (pin_A4) // green
#define MICROPY_HW_LED2             (pin_A4) // same as LED1
#define MICROPY_HW_LED3             (pin_A4) // same as LED1
#define MICROPY_HW_LED4             (pin_A4)  // same as LED1
#define MICROPY_HW_LED_OTYPE        (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin)      (pin->gpio->BSRRL = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin)     (pin->gpio->BSRRH = pin->pin_mask)

// SD card detect switch (not used, always on)
#define MICROPY_HW_SDCARD_DETECT_PIN        (pin_A8)
#define MICROPY_HW_SDCARD_DETECT_PULL       (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT    (1)

// USB config
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
micropython port for HydraBus 2014-06-02 15:43:02 -04:00			`#define HYDRABUSV10`

			`#define MICROPY_HW_BOARD_NAME "HydraBus1.0"`
Change MCU name config micro 2014-06-26 18:35:53 -04:00			`#define MICROPY_HW_MCU_NAME "STM32F4"`
micropython port for HydraBus 2014-06-02 15:43:02 -04:00
			`#define MICROPY_HW_HAS_SWITCH (1)`
			`#define MICROPY_HW_HAS_SDCARD (1)`
			`#define MICROPY_HW_HAS_MMA7660 (0)`
			`#define MICROPY_HW_HAS_LIS3DSH (0)`
			`#define MICROPY_HW_HAS_LCD (0)`
			`#define MICROPY_HW_ENABLE_RNG (1)`
			`#define MICROPY_HW_ENABLE_RTC (0)`
			`#define MICROPY_HW_ENABLE_TIMER (1)`
			`#define MICROPY_HW_ENABLE_SERVO (0)`
			`#define MICROPY_HW_ENABLE_DAC (1)`
stmhal: Add config option to disable/enable CAN driver. 2014-10-05 13:05:26 -04:00			`#define MICROPY_HW_ENABLE_CAN (0)`
micropython port for HydraBus 2014-06-02 15:43:02 -04:00
stmhal: Make HSE PLL parameters configurable per board. 2015-04-18 10:30:04 -04:00			`// HSE is 8MHz`
			`#define MICROPY_HW_CLK_PLLM (8)`
			`#define MICROPY_HW_CLK_PLLN (336)`
			`#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)`
			`#define MICROPY_HW_CLK_PLLQ (7)`

stmhal: Allow to configure UART pins completely via mpconfigboard.h. 2015-05-02 12:31:39 -04:00			`// UART config`
			`#define MICROPY_HW_UART1_PORT (GPIOA)`
			`#define MICROPY_HW_UART1_PINS (GPIO_PIN_9 \| GPIO_PIN_10)`
			`#define MICROPY_HW_UART2_PORT (GPIOA)`
			`#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 \| GPIO_PIN_3)`
			`#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)`
			`#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)`
			`#define MICROPY_HW_UART3_PORT (GPIOD)`
			`#define MICROPY_HW_UART3_PINS (GPIO_PIN_8 \| GPIO_PIN_9)`
			`#define MICROPY_HW_UART3_RTS (GPIO_PIN_12)`
			`#define MICROPY_HW_UART3_CTS (GPIO_PIN_11)`
			`#define MICROPY_HW_UART4_PORT (GPIOA)`
			`#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 \| GPIO_PIN_1)`
			`#define MICROPY_HW_UART6_PORT (GPIOC)`
			`#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 \| GPIO_PIN_7)`

stmhal: Make I2C busses and their pins configurable in mpconfigboard.h. 2015-04-18 11:12:57 -04:00			`// I2C busses`
			`#define MICROPY_HW_I2C1_SCL (pin_B6)`
			`#define MICROPY_HW_I2C1_SDA (pin_B7)`
			`#define MICROPY_HW_I2C2_SCL (pin_B10)`
			`#define MICROPY_HW_I2C2_SDA (pin_B11)`

stmhal: For SPI config, use HW_SPIx_SCK instead of HW_ENABLE_SPIx. Previously, SPI was configured by a board defining MICROPY_HW_ENABLE_SPIx to 0 or 1. Now, the board should define MICROPY_HW_SPIx_SCK, MISO, MOSI and NSS. This makes it the same as how I2C is configured. 2015-12-12 10:02:02 -05:00			`// SPI busses`
			`#define MICROPY_HW_SPI1_NSS (pin_A4)`
			`#define MICROPY_HW_SPI1_SCK (pin_A5)`
			`#define MICROPY_HW_SPI1_MISO (pin_A6)`
			`#define MICROPY_HW_SPI1_MOSI (pin_A7)`
			`#define MICROPY_HW_SPI2_NSS (pin_B12)`
			`#define MICROPY_HW_SPI2_SCK (pin_B13)`
			`#define MICROPY_HW_SPI2_MISO (pin_B14)`
			`#define MICROPY_HW_SPI2_MOSI (pin_B15)`
			`#define MICROPY_HW_SPI3_NSS (pin_A4)`
			`#define MICROPY_HW_SPI3_SCK (pin_B3)`
			`#define MICROPY_HW_SPI3_MISO (pin_B4)`
			`#define MICROPY_HW_SPI3_MOSI (pin_B5)`

micropython port for HydraBus 2014-06-02 15:43:02 -04:00			`// USRSW/UBTN (Needs Jumper UBTN) is pulled low. Pressing the button makes the input go high.`
			`#define MICROPY_HW_USRSW_PIN (pin_A0)`
			`#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)`
			`#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)`
			`#define MICROPY_HW_USRSW_PRESSED (1)`

			`// The HydraBus has 1 LED (Needs jumper on ULED)`
			`#define MICROPY_HW_LED1 (pin_A4) // green`
			`#define MICROPY_HW_LED2 (pin_A4) // same as LED1`
			`#define MICROPY_HW_LED3 (pin_A4) // same as LED1`
			`#define MICROPY_HW_LED4 (pin_A4) // same as LED1`
			`#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)`
			`#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)`
			`#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)`

			`// SD card detect switch (not used, always on)`
			`#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)`
			`#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)`
			`#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)`
stmhal: Add MICROPY_HW_USB_OTG_ID_PIN config, set for relevant boards. This config option is for the USB OTG pin, pin A10. This is used on some boards but not others. Eg PYBv3 uses PA10 for LED(2), so it shouldn't be used for OTG ID (actually PA10 is multiplexed on this board, but defaults to LED(2)). Partially addresses issue #1059. 2015-01-12 11:13:29 -05:00
			`// USB config`
			`#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)`