6a31dcd638
Instead of downloading "a" version, these links point to history from where you can download the verson you like.
148 lines
6.6 KiB
Markdown
148 lines
6.6 KiB
Markdown
# MicroPython Port To The Nordic Semiconductor nRF Series
|
|
|
|
This is a port of MicroPython to the Nordic Semiconductor nRF series of chips.
|
|
|
|
## Supported Features
|
|
|
|
* UART
|
|
* SPI
|
|
* LEDs
|
|
* Pins
|
|
* ADC
|
|
* I2C
|
|
* PWM (nRF52 only)
|
|
* Temperature
|
|
* RTC (Real Time Counter. Low-Power counter)
|
|
* BLE support including:
|
|
* Peripheral role on nrf51 targets
|
|
* Central role and Peripheral role on nrf52 targets
|
|
* _REPL over Bluetooth LE_ (optionally using WebBluetooth)
|
|
* ubluepy: Bluetooth LE module for MicroPython
|
|
* 1 non-connectable advertiser while in connection
|
|
|
|
## Tested Hardware
|
|
|
|
* nRF51
|
|
* [micro:bit](http://microbit.org/)
|
|
* PCA10000 (dongle)
|
|
* PCA10001
|
|
* PCA10028
|
|
* PCA10031 (dongle)
|
|
* [WT51822-S4AT](http://www.wireless-tag.com/wireless_module/BLE/WT51822-S4AT.html)
|
|
* nRF52832
|
|
* [PCA10040](http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52%2Fdita%2Fnrf52%2Fdevelopment%2Fnrf52_dev_kit.html)
|
|
* [Adafruit Feather nRF52](https://www.adafruit.com/product/3406)
|
|
* [Thingy:52](http://www.nordicsemi.com/eng/Products/Nordic-Thingy-52)
|
|
* [Arduino Primo](http://www.arduino.org/products/boards/arduino-primo)
|
|
* nRF52840
|
|
* [PCA10056](http://www.nordicsemi.com/eng/Products/nRF52840-Preview-DK)
|
|
|
|
## Compile and Flash
|
|
|
|
Prerequisite steps for building the nrf port:
|
|
|
|
git clone <URL>.git micropython
|
|
cd micropython
|
|
git submodule update --init
|
|
make -C mpy-cross
|
|
|
|
By default, the PCA10040 (nrf52832) is used as compile target. To build and flash issue the following command inside the ports/nrf/ folder:
|
|
|
|
make
|
|
make flash
|
|
|
|
Alternatively the target board could be defined:
|
|
|
|
make BOARD=pca10040
|
|
make flash
|
|
|
|
## Compile and Flash with Bluetooth Stack
|
|
|
|
First prepare the bluetooth folder by downloading Bluetooth LE stacks and headers:
|
|
|
|
./drivers/bluetooth/download_ble_stack.sh
|
|
|
|
If the Bluetooth stacks has been downloaded, compile the target with the following command:
|
|
|
|
make BOARD=pca10040 SD=s132
|
|
|
|
The **make sd** will trigger a flash of the bluetooth stack before that application is flashed. Note that **make sd** will perform a full erase of the chip, which could cause 3rd party bootloaders to also be wiped.
|
|
|
|
make BOARD=pca10040 SD=s132 sd
|
|
|
|
Note: further tuning of features to include in bluetooth or even setting up the device to use REPL over Bluetooth can be configured in the `bluetooth_conf.h`.
|
|
|
|
## Compile with frozen modules
|
|
|
|
Frozen modules are Python modules compiled to bytecode and added to the firmware
|
|
image, as part of MicroPython. They can be imported as usual, using the `import`
|
|
statement. The advantage is that frozen modules use a lot less RAM as the
|
|
bytecode is stored in flash, not in RAM like when importing from a filesystem.
|
|
Also, frozen modules are available even when no filesystem is present to import
|
|
from.
|
|
|
|
To use frozen modules, put them in a directory (e.g. `freeze/`) and supply
|
|
`make` with the given directory. For example:
|
|
|
|
make BOARD=pca10040 FROZEN_MPY_DIR=freeze
|
|
|
|
## Enable MICROPY_FATFS
|
|
As the `oofatfs` module is not having header guards that can exclude the implementation compile time, this port provides a flag to enable it explicitly. The MICROPY_FATFS is by default set to 0 and has to be set to 1 if `oofatfs` files should be compiled. This will be in addition of setting `MICROPY_VFS` and `MICROPY_VFS_FAT` in mpconfigport.h.
|
|
|
|
For example:
|
|
|
|
make BOARD=pca10040 MICROPY_FATFS=1
|
|
|
|
## Target Boards and Make Flags
|
|
|
|
Target Board (BOARD) | Bluetooth Stack (SD) | Bluetooth Support | Flash Util
|
|
---------------------|-------------------------|------------------------|-------------------------------
|
|
microbit | s110 | Peripheral | [PyOCD](#pyocdopenocd-targets)
|
|
pca10000 | s110 | Peripheral | [Segger](#segger-targets)
|
|
pca10001 | s110 | Peripheral | [Segger](#segger-targets)
|
|
pca10028 | s110 | Peripheral | [Segger](#segger-targets)
|
|
pca10031 | s110 | Peripheral | [Segger](#segger-targets)
|
|
wt51822_s4at | s110 | Peripheral | Manual, see [datasheet](https://4tronix.co.uk/picobot2/WT51822-S4AT.pdf) for pinout
|
|
pca10040 | s132 | Peripheral and Central | [Segger](#segger-targets)
|
|
feather52 | s132 | Peripheral and Central | Manual, SWDIO and SWCLK solder points on the bottom side of the board
|
|
arduino_primo | s132 | Peripheral and Central | [PyOCD](#pyocdopenocd-targets)
|
|
pca10056 | s140 | Peripheral and Central | [Segger](#segger-targets)
|
|
|
|
## Segger Targets
|
|
|
|
Install the necessary tools to flash and debug using Segger:
|
|
|
|
[JLink Download](https://www.segger.com/downloads/jlink#)
|
|
|
|
[nrfjprog linux-32bit Download](https://www.nordicsemi.com/eng/nordic/Products/nRF52840/nRF5x-Command-Line-Tools-Linux32/58857)
|
|
|
|
[nrfjprog linux-64bit Download](https://www.nordicsemi.com/eng/nordic/Products/nRF52840/nRF5x-Command-Line-Tools-Linux64/58852)
|
|
|
|
[nrfjprog osx Download](https://www.nordicsemi.com/eng/nordic/Products/nRF52840/nRF5x-Command-Line-Tools-OSX/58855)
|
|
|
|
[nrfjprog win32 Download](https://www.nordicsemi.com/eng/nordic/Products/nRF52840/nRF5x-Command-Line-Tools-Win32/58850)
|
|
|
|
note: On Linux it might be required to link SEGGER's `libjlinkarm.so` inside nrfjprog's folder.
|
|
|
|
## PyOCD/OpenOCD Targets
|
|
|
|
Install the necessary tools to flash and debug using OpenOCD:
|
|
|
|
sudo apt-get install openocd
|
|
sudo pip install pyOCD
|
|
|
|
## Bluetooth LE REPL
|
|
|
|
The port also implements a BLE REPL driver. This feature is disabled by default, as it will deactivate the UART REPL when activated. As some of the nRF devices only have one UART, using the BLE REPL free's the UART instance such that it can be used as a general UART peripheral not bound to REPL.
|
|
|
|
The configuration can be enabled by editing the `bluetooth_conf.h` and set `MICROPY_PY_BLE_NUS` to 1.
|
|
|
|
When enabled you have different options to test it:
|
|
* [NUS Console for Linux](https://github.com/tralamazza/nus_console) (recommended)
|
|
* [WebBluetooth REPL](https://aykevl.nl/apps/nus/) (experimental)
|
|
|
|
Other:
|
|
* nRF UART application for IPhone/Android
|
|
|
|
WebBluetooth mode can also be configured by editing `bluetooth_conf.h` and set `BLUETOOTH_WEBBLUETOOTH_REPL` to 1. This will alternate advertisement between Eddystone URL and regular connectable advertisement. The Eddystone URL will point the phone or PC to download [WebBluetooth REPL](https://aykevl.nl/apps/nus/) (experimental), which subsequently can be used to connect to the Bluetooth REPL from the PC or Phone browser.
|