232 lines
8.1 KiB
Markdown
232 lines
8.1 KiB
Markdown
MicroPython port to the ESP32
|
|
=============================
|
|
|
|
This is a port of MicroPython to the Espressif ESP32 series of
|
|
microcontrollers. It uses the ESP-IDF framework and MicroPython runs as
|
|
a task under FreeRTOS.
|
|
|
|
Supported features include:
|
|
- REPL (Python prompt) over UART0.
|
|
- 16k stack for the MicroPython task and approximately 100k Python heap.
|
|
- Many of MicroPython's features are enabled: unicode, arbitrary-precision
|
|
integers, single-precision floats, complex numbers, frozen bytecode, as
|
|
well as many of the internal modules.
|
|
- Internal filesystem using the flash (currently 2M in size).
|
|
- The machine module with GPIO, UART, SPI, software I2C, ADC, DAC, PWM,
|
|
TouchPad, WDT and Timer.
|
|
- The network module with WLAN (WiFi) support.
|
|
- Bluetooth low-energy (BLE) support via the bluetooth module.
|
|
|
|
Initial development of this ESP32 port was sponsored in part by Microbric Pty Ltd.
|
|
|
|
Setting up ESP-IDF and the build environment
|
|
--------------------------------------------
|
|
|
|
MicroPython on ESP32 requires the Espressif IDF version 4 (IoT development
|
|
framework, aka SDK). The ESP-IDF includes the libraries and RTOS needed to
|
|
manage the ESP32 microcontroller, as well as a way to manage the required
|
|
build environment and toolchains needed to build the firmware.
|
|
|
|
The ESP-IDF changes quickly and MicroPython only supports certain versions.
|
|
Currently MicroPython supports v4.0.2, v4.1.1, v4.2.2, v4.3.2 and v4.4,
|
|
although other IDF v4 versions may also work.
|
|
|
|
To install the ESP-IDF the full instructions can be found at the
|
|
[Espressif Getting Started guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html#installation-step-by-step).
|
|
|
|
If you are on a Windows machine then the [Windows Subsystem for
|
|
Linux](https://msdn.microsoft.com/en-au/commandline/wsl/install_guide) is the
|
|
most efficient way to install the ESP32 toolchain and build the project. If
|
|
you use WSL then follow the Linux instructions rather than the Windows
|
|
instructions.
|
|
|
|
The Espressif instructions will guide you through using the `install.sh`
|
|
(or `install.bat`) script to download the toolchain and set up your environment.
|
|
The steps to take are summarised below.
|
|
|
|
To check out a copy of the IDF use git clone:
|
|
|
|
```bash
|
|
$ git clone -b v4.0.2 --recursive https://github.com/espressif/esp-idf.git
|
|
```
|
|
|
|
You can replace `v4.0.2` with `v4.2.2` or `v4.4` or any other supported version.
|
|
(You don't need a full recursive clone; see the `ci_esp32_setup` function in
|
|
`tools/ci.sh` in this repository for more detailed set-up commands.)
|
|
|
|
If you already have a copy of the IDF then checkout a version compatible with
|
|
MicroPython and update the submodules using:
|
|
|
|
```bash
|
|
$ cd esp-idf
|
|
$ git checkout v4.2
|
|
$ git submodule update --init --recursive
|
|
```
|
|
|
|
After you've cloned and checked out the IDF to the correct version, run the
|
|
`install.sh` script:
|
|
|
|
```bash
|
|
$ cd esp-idf
|
|
$ ./install.sh # (or install.bat on Windows)
|
|
$ source export.sh # (or export.bat on Windows)
|
|
```
|
|
|
|
The `install.sh` step only needs to be done once. You will need to source
|
|
`export.sh` for every new session.
|
|
|
|
**Note:** If you are building MicroPython for the ESP32-S2, ESP32-C3 or ESP32-S3,
|
|
please ensure you are using the following required IDF versions:
|
|
- ESP32-S3 currently requires `v4.4` or later.
|
|
- ESP32-S2 and ESP32-C3 require `v4.3.1` or later.
|
|
|
|
Building the firmware
|
|
---------------------
|
|
|
|
The MicroPython cross-compiler must be built to pre-compile some of the
|
|
built-in scripts to bytecode. This can be done by (from the root of
|
|
this repository):
|
|
|
|
```bash
|
|
$ make -C mpy-cross
|
|
```
|
|
|
|
Then to build MicroPython for the ESP32 run:
|
|
|
|
```bash
|
|
$ cd ports/esp32
|
|
$ make submodules
|
|
$ make
|
|
```
|
|
|
|
This will produce a combined `firmware.bin` image in the `build-GENERIC/`
|
|
subdirectory (this firmware image is made up of: bootloader.bin, partitions.bin
|
|
and micropython.bin).
|
|
|
|
To flash the firmware you must have your ESP32 module in the bootloader
|
|
mode and connected to a serial port on your PC. Refer to the documentation
|
|
for your particular ESP32 module for how to do this.
|
|
You will also need to have user permissions to access the `/dev/ttyUSB0` device.
|
|
On Linux, you can enable this by adding your user to the `dialout` group, and
|
|
rebooting or logging out and in again. (Note: on some distributions this may
|
|
be the `uucp` group, run `ls -la /dev/ttyUSB0` to check.)
|
|
|
|
```bash
|
|
$ sudo adduser <username> dialout
|
|
```
|
|
|
|
If you are installing MicroPython to your module for the first time, or
|
|
after installing any other firmware, you should first erase the flash
|
|
completely:
|
|
|
|
```bash
|
|
$ make erase
|
|
```
|
|
|
|
To flash the MicroPython firmware to your ESP32 use:
|
|
|
|
```bash
|
|
$ make deploy
|
|
```
|
|
|
|
The default ESP32 board build by the above commands is the `GENERIC` one, which
|
|
should work on most ESP32 modules. You can specify a different board by passing
|
|
`BOARD=<board>` to the make commands, for example:
|
|
|
|
```bash
|
|
$ make BOARD=GENERIC_SPIRAM
|
|
```
|
|
|
|
Note: the above "make" commands are thin wrappers for the underlying `idf.py`
|
|
build tool that is part of the ESP-IDF. You can instead use `idf.py` directly,
|
|
for example:
|
|
|
|
```bash
|
|
$ idf.py build
|
|
$ idf.py -D MICROPY_BOARD=GENERIC_SPIRAM build
|
|
$ idf.py flash
|
|
```
|
|
|
|
Getting a Python prompt on the device
|
|
-------------------------------------
|
|
|
|
You can get a prompt via the serial port, via UART0, which is the same UART
|
|
that is used for programming the firmware. The baudrate for the REPL is
|
|
115200 and you can use a command such as:
|
|
|
|
```bash
|
|
$ picocom -b 115200 /dev/ttyUSB0
|
|
```
|
|
|
|
or
|
|
|
|
```bash
|
|
$ miniterm.py /dev/ttyUSB0 115200
|
|
```
|
|
|
|
You can also use `idf.py monitor`.
|
|
|
|
Configuring the WiFi and using the board
|
|
----------------------------------------
|
|
|
|
The ESP32 port is designed to be (almost) equivalent to the ESP8266 in
|
|
terms of the modules and user-facing API. There are some small differences,
|
|
notably that the ESP32 does not automatically connect to the last access
|
|
point when booting up. But for the most part the documentation and tutorials
|
|
for the ESP8266 should apply to the ESP32 (at least for the components that
|
|
are implemented).
|
|
|
|
See http://docs.micropython.org/en/latest/esp8266/esp8266/quickref.html for
|
|
a quick reference, and http://docs.micropython.org/en/latest/esp8266/esp8266/tutorial/intro.html
|
|
for a tutorial.
|
|
|
|
The following function can be used to connect to a WiFi access point (you can
|
|
either pass in your own SSID and password, or change the defaults so you can
|
|
quickly call `wlan_connect()` and it just works):
|
|
```python
|
|
def wlan_connect(ssid='MYSSID', password='MYPASS'):
|
|
import network
|
|
wlan = network.WLAN(network.STA_IF)
|
|
if not wlan.active() or not wlan.isconnected():
|
|
wlan.active(True)
|
|
print('connecting to:', ssid)
|
|
wlan.connect(ssid, password)
|
|
while not wlan.isconnected():
|
|
pass
|
|
print('network config:', wlan.ifconfig())
|
|
```
|
|
|
|
Note that some boards require you to configure the WiFi antenna before using
|
|
the WiFi. On Pycom boards like the LoPy and WiPy 2.0 you need to execute the
|
|
following code to select the internal antenna (best to put this line in your
|
|
boot.py file):
|
|
```python
|
|
import machine
|
|
antenna = machine.Pin(16, machine.Pin.OUT, value=0)
|
|
```
|
|
|
|
Defining a custom ESP32 board
|
|
-----------------------------
|
|
|
|
The default ESP-IDF configuration settings are provided by the `GENERIC`
|
|
board definition in the directory `boards/GENERIC`. For a custom configuration
|
|
you can define your own board directory. Start a new board configuration by
|
|
copying an existing one (like `GENERIC`) and modifying it to suit your board.
|
|
|
|
MicroPython specific configuration values are defined in the board-specific
|
|
`mpconfigboard.h` file, which is included by `mpconfigport.h`. Additional
|
|
settings are put in `mpconfigboard.cmake`, including a list of `sdkconfig`
|
|
files that configure ESP-IDF settings. Some standard `sdkconfig` files are
|
|
provided in the `boards/` directory, like `boards/sdkconfig.ble`. You can
|
|
also define custom ones in your board directory.
|
|
|
|
See existing board definitions for further examples of configuration.
|
|
|
|
Configuration
|
|
Troubleshooting
|
|
---------------
|
|
|
|
* Continuous reboots after programming: Ensure `CONFIG_ESPTOOLPY_FLASHMODE` is
|
|
correct for your board (e.g. ESP-WROOM-32 should be DIO). Then perform a
|
|
`make clean`, rebuild, redeploy.
|