Mike Causer
47b778332a
all: Replace busses with buses.
...
"buses" is the widely accepted plural form of "bus".
2021-05-20 23:22:03 +10:00
Reinhard Feger
032e095620
stm32/boards/NUCLEO_H743ZI: Enable ethernet peripheral.
2020-12-08 15:27:51 +11:00
roland van straten
43b576d88d
stm32/boards/NUCLEO_H743ZI: Add extra pins and peripheral definitions.
...
- Corrected pin assignments and checked with CubeMX.
- Added additional I2C and UARTs.
- Added Ethernet interface definitions with lwIP and SSL support (but
Ethernet is currently unsupported on H7 MCUs so not fully enabled).
2019-12-19 16:54:33 +11:00
iabdalkader
4f78ba3cf4
stm32/boards/NUCLEO_H743ZI: Enable FDCAN on this board.
2019-09-23 17:00:54 +10:00
Damien George
009b1f6559
stm32/boards: Rework all stm32??xx_hal_conf.h files to use common code.
...
This eliminates a lot of duplicated code in these header files.
2019-06-25 14:18:24 +10:00
iabdalkader
746fcea7f8
stm32/boards/NUCLEO_H743ZI: Enable SPI3 on this board.
2019-05-15 16:08:10 +10:00
Damien George
4831e38c7e
stm32/boards/NUCLEO_H743ZI: Add config options to support mboot.
2019-04-08 14:34:37 +10:00
Damien George
9670b26526
stm32: Rename MICROPY_HW_HAS_SDCARD to MICROPY_HW_ENABLE_SDCARD.
...
For consistency with the majority of other MICROPY_HW_ENABLE_xxx macros.
2019-04-01 15:21:26 +11:00
roland
30ed2b3cab
stm32/system_stm32: Introduce configuration defines for PLL3 settings.
...
A board must be able to set the PLL3 values based on the HSE that it uses.
2018-11-01 13:25:47 +11:00
rolandvs
958fa74521
stm32/boards: Ensure USB OTG power is off for NUCLEO_F767ZI.
...
And update the GPIO init for NUCLEO_H743ZI to consistently use the mphal
functions.
2018-05-30 09:51:19 +10:00
iabdalkader
28c9824c51
stm32/boards/NUCLEO_H743ZI: Enable ADC peripheral.
2018-05-01 15:39:03 +10:00
Damien George
c0dd9be606
stm32/boards/NUCLEO_H743ZI: Use priority 0 for SysTick IRQ.
...
This follows how all other boards are configured.
2018-04-27 15:16:45 +10:00
iabdalkader
d870a4e835
stm32/boards/NUCLEO_H743ZI: Enable RNG for this board.
2018-04-23 16:43:16 +10:00
iabdalkader
e1e49adb86
stm32/boards/NUCLEO_H743ZI: Enable DAC peripheral.
2018-04-10 14:21:26 +10:00
iabdalkader
cf1d6df05a
stm32/boards/NUCLEO_H743ZI: Enable SD card support.
2018-03-28 13:25:00 +11:00
Damien George
1efe6a0316
stm32/boards/NUCLEO_H743ZI: Update to build with new linker management.
2018-03-28 13:20:48 +11:00
iabdalkader
7b0a020a02
stm32/boards/NUCLEO_H743ZI: Disable uSD transceiver.
...
There's no uSD Transceiver on this NUCLEO board.
2018-03-20 23:26:03 +11:00
iabdalkader
1e0a67f290
stm32/boards/NUCLEO_H743ZI: Enable hardware I2C support.
2018-03-20 23:25:43 +11:00
iabdalkader
fabfacf3d7
stm32/boards: Add new NUCLEO_H743ZI board configuration files.
...
USB serial and mass storage works, and the REPL is also available via the
UART through the on-board ST-LINK.
2018-03-09 15:08:11 +11:00
