This changes lots of files to unify `board.h` across ports. It adds
`board_deinit` when CIRCUITPY_ALARM is set. `main.c` uses it to
deinit the board before deep sleeping (even when pretending.)
Deep sleep is now a two step process for the port. First, the
port should prepare to deep sleep based on the given alarms. It
should set alarms for both deep and pretend sleep. In particular,
the pretend versions should be set immediately so that we don't
miss an alarm as we shutdown. These alarms should also wake from
`port_idle_until_interrupt` which is used when pretending to deep
sleep.
Second, when real deep sleeping, `alarm_enter_deep_sleep` is called.
The port should set any alarms it didn't during prepare based on
data it saved internally during prepare.
ESP32-S2 sleep is a bit reorganized to locate more logic with
TimeAlarm. This will help it scale to more alarm types.
Fixes#3786
In time, we should transition interrupt driven background tasks out of the
overall run_background_tasks into distinct background callbacks,
so that the number of checks that occur with each tick is reduced.
Check to see if the current exception is a Watchdog exception, if it's
enabled. This ensures we break out of the current sleep() if a watchdog
timeout hits.
Signed-off-by: Sean Cross <sean@xobs.io>
Introduces a way to place CircuitPython code and data into
tightly coupled memory (TCM) which is accessible by the CPU in a
single cycle. It also frees up room in the corresponding cache for
intermittent data. Loading from external flash is slow!
The data cache is also now enabled.
Adds support for the iMX RT 1021 chip. Adds three new boards:
* iMX RT 1020 EVK
* iMX RT 1060 EVK
* Teensy 4.0
Related to #2492, #2472 and #2477. Fixes#2475.
This improves performance of running python code by 34%, based
on the "pystone" benchmark on metro m4 express at 5000 passes
(1127.65 -> 1521.6 passes/second).
In addition, by instrumenting the tick function and monitoring on an
oscilloscope, the time actually spent in run_background_tasks() on
the metro m4 decreases from average 43% to 0.5%. (however, there's
some additional overhead that is moved around and not accounted for
in that "0.5%" figure, each time supervisor_run_background_tasks_if_tick
is called but no tick has occurred)
On the CPB, it increases pystone from 633 to 769, a smaller percentage
increase of 21%. I did not measure the time actually spent in
run_background_tasks() on CPB.
Testing performed: on metro m4 and cpb, run pystone adapted from python3.4
(change time.time to time.monotonic for sub-second resolution)
Besides running a 5000 pass test, I also ran a 50-pass test while
scoping how long an output pin was set. Average: 34.59ms or 1445/s on m4,
67.61ms or 739/s on cbp, both matching the other pystone result reasonably
well.
import pystone
import board
import digitalio
import time
d = digitalio.DigitalInOut(board.D13)
d.direction = digitalio.Direction.OUTPUT
while True:
d.value = 0
time.sleep(.01)
d.value = 1
pystone.main(50)
This code is shared by most parts, except where not all the #ifdefs
inside the tick function were present in all ports. This mostly would
have broken gamepad tick support on non-samd ports.
The "ms32" and "ms64" variants of the tick functions are introduced
because there is no 64-bit atomic read. Disabling interrupts avoids
a low probability bug where milliseconds could be off by ~49.5 days
once every ~49.5 days (2^32 ms).
Avoiding disabling interrupts when only the low 32 bits are needed is a minor
optimization.
Testing performed: on metro m4 express, USB still works and
time.monotonic_ns() still counts up
Dan Halbert
Scott Shawcroft
Dan Halbert
Jeff Epler
DavePutz
Diego Elio Pettenò
Sean Cross