All user interface (LED, button) code has been moved to ui.c, and the
interface to this code with the rest of the system now goes through calls
to mboot_state_change(). This state-change function can be overridden by a
board to fully customise the user interface behaviour.
Signed-off-by: Damien George <damien@micropython.org>
Tested on PYBV10 and PYBD_SF6, with MBOOT_FSLOAD enabled and programming
new firmware from a .dfu.gz file stored on the SD card.
Signed-off-by: Damien George <damien@micropython.org>
If enabled via MBOOT_ADDRESS_SPACE_64BIT (it's disabled by default) then
read addresses will be 64-bit.
Signed-off-by: Damien George <damien@micropython.org>
Even if MBOOT_FSLOAD is disabled, mboot should still check for 0x70ad0080
so it can immediately return to the application if this feature is not
enabled. Otherwise mboot will get stuck in DFU mode.
Signed-off-by: Damien George <damien@micropython.org>
If MBOOT_BOARD_ENTRY_INIT is defined by a board then that function must now
make sure system clocks are configured, eg by calling mboot_entry_init().
Signed-off-by: Damien George <damien@micropython.org>
If a board wants to customise the clocks it can define the following:
MBOOT_CLK_PLLM
MBOOT_CLK_PLLN
MBOOT_CLK_PLLP
MBOOT_CLK_PLLQ
MBOOT_CLK_PLLR (only needed on STM32H7)
MBOOT_FLASH_LATENCY
MBOOT_CLK_AHB_DIV
MBOOT_CLK_APB1_DIV
MBOOT_CLK_APB2_DIV
MBOOT_CLK_APB3_DIV (only needed on STM32H7)
MBOOT_CLK_APB4_DIV (only needed on STM32H7)
Signed-off-by: Damien George <damien@micropython.org>
PLL3-Q is more reliable than PLL1-Q for the USB clock source when entering
mboot from various reset states (eg power on vs MCU reset). (It was found
that if the main application used PLL3-Q then sometimes the USB clock
source would stay stuck on PLL3-Q and not switch to PLL1-Q after a reset.)
Other related changes:
- SystemCoreClockUpdate() should be called on H7 because the calculation
can be involved in some cases.
- __set_PRIMASK(0) should be called because on H7 the built-in ST DFU
bootloader exits with IRQs disabled.
Signed-off-by: Damien George <damien@micropython.org>
So that a board can access other HAL_RCC functions if it needs them (this
was not possible previously by just adding hal_rcc.c to the src list for a
board because it would clash with the custom HAL_RCC_GetHCLKFreq function).
Signed-off-by: Damien George <damien@micropython.org>
Leaving the bootloader from an IRQ (eg USB or I2C IRQ) will not work if
MBOOT_LEAVE_BOOTLOADER_VIA_RESET is disabled, ie if mboot jumps directly to
the application. This is because the CPU will still be in IRQ state when
the application starts and IRQs of lower priority will be blocked.
Fix this by setting a flag when the bootloader should finish, and exit the
bootloader always from the main (top level) thread.
This also improves the USB behaviour of mboot: it no longer abruptly
disconnects when the manifest command is sent.
Signed-off-by: Damien George <damien@micropython.org>
A board can now customise mboot with:
- MBOOT_LED1, MBOOT_LED2, MBOOT_LED3, MBOOT_LED4: if it needs to have
different LEDs for mboot compared to the application
- MBOOT_BOARD_LED_INIT: if it needs a fully customised LED init function
- MBOOT_BOARD_LED_STATE: if it needs a fully customised LED state-setting
function
- MBOOT_BOARD_GET_RESET_MODE: if it needs a fully customised function to
get the reset mode
With full customisation, the only requirement is a single LED to show the
status of the bootloader (idle, erasing, flashing, etc), which can be
configured to do nothing if needed.
Signed-off-by: Damien George <damien@micropython.org>
It is enabled by default to get the standard behaviour of doing a reset
after it is finished, but can be disabled by a board to jump straight to
the application (likely the board needs to use MBOOT_BOARD_CLEANUP to make
this work).
The application is passed a reset mode of BOARDCTRL_RESET_MODE_BOOTLOADER
if the bootloader was active and entered via a jump.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define MBOOT_TEXT0_ADDR to place mboot at a location other
than 0x08000000. This can be useful if, for example, there is already a
different bootloader on the device.
Signed-off-by: Damien George <damien@micropython.org>
And use the same boardctrl.h header for both the application and mboot so
these constants are consistent.
Signed-off-by: Damien George <damien@micropython.org>
This new element takes the form: (ELEM_TYPE_STATUS, 4, <address>). If this
element is present in the mboot command then mboot will store to the given
address the result of the filesystem firmware update process. The address
can for example be an RTC backup register.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
Polling mode will cause failures with the mass-erase command due to USB
timeouts, because the USB IRQs are not being serviced. Swiching from
polling to IRQ mode fixes this because the USB IRQs can be serviced between
page erases.
Note that when the flash is being programmed or erased the MCU is halted
and cannot respond to USB IRQs, because mboot runs from flash, as opposed
to the built-in bootloader which is in system ROM. But the maximum delay
in responding to an IRQ is the time taken to erase a single page, about
100ms for large pages, and that is short enough that the USB does not
timeout on the host side.
Recent tests have shown that in the current mboot code IRQ mode is pretty
much the same speed as polling mode (within timing error), code size is
slightly reduced in IRQ mode, and IRQ mode idles at about half of the power
consumption as polling mode.
This is treated more like a "delay before continuing" in the spec and
official tools and does not appear to be really needed. In particular,
downloading firmware is much slower with non-zero timeouts because the host
must pause by the timeout between sending each DFU_GETSTATUS to poll for
download/erase complete.
The implementation internally uses sector erase to wipe everything except
the sector(s) that mboot lives in (by erasing starting from
APPLICATION_ADDR).
The erase command can take some time (eg an STM32F765 with 2MB of flash
takes 8 to 10 seconds). This time is normally enough to make pydfu.py fail
with a timeout. The DFU standard includes a mechanism for the DFU device
to request a longer timeout as part of the get-status response just before
starting an operation. This timeout functionality has been implemented
here.
By passing through the I2C instance to the application callbacks, the
application can implement multiple I2C slave devices on different
peripherals (eg I2C1 and I2C2).
This commit also adds a proper rw argument to i2c_slave_process_addr_match
for F7/H7/WB MCUs, and enables the i2c_slave_process_tx_end callback.
Mboot is also updated for these changes.
Signed-off-by: Damien George <damien@micropython.org>
Commit 8675858465 switched to using the CMSIS
provided SystemInit function which sets VTOR to 0x00000000 (previously it
was 0x08000000). A VTOR of 0x00000000 will be correct on some MCUs but not
on others where the built-in bootloader is remapped to this address, via
__HAL_SYSCFG_REMAPMEMORY_SYSTEMFLASH().
To make sure mboot has the correct vector table, this commit explicitly
sets VTOR to the correct value of 0x08000000.
Signed-off-by: Damien George <damien@micropython.org>
There's no need to duplicate this functionality in mboot, the code provided
in stm32lib/CMSIS does the same thing and makes it easier to support other
MCU series.
Signed-off-by: Damien George <damien@micropython.org>
The flash functions in ports/stm32/flash.c are almost identical to those in
ports/stm32/mboot/main.c, so remove the duplicated code in mboot and use
instead the main stm32 code. This also allows supporting other MCU series.
Signed-off-by: Damien George <damien@micropython.org>
In mboot, the ability to override the USB vendor/product id's was added
back in 5688c9ba09. However, when the main
firmware is turned into a DFU file the default VID/PID are used there.
pydfu.py doesn't care about this but dfu-util does and prevents its use
when the VID/PID don't match.
This commit exposes BOOTLOADER_DFU_USB_VID/PID as make variables, for use
on either command line or mpconfigboard.mk, to set VID/PID in both mboot
and DFU files.
The "led" argument is always a pointer to the GPIO port, or'd with the pin
that the LED is on, so testing that it is "1" is unnecessary. The type of
"led" is also changed to uint32_t so it can properly hold a 32-bit pointer.
Updating the LED0 state from systick handler ensures LED0 is always
consistent with its flash rate regardless of other processing going on in
either interrupts or main. This improves the visible stability of the
bootloader, rather than LED0 flashing somewhat randomly at times.
This commit also changes the LED0 flash rate depending on the current state
of DFU, giving slightly more visual feedback on what the device is doing.
Mboot currently requires at least three LEDs to display each of the four
states. However, since there are only four possible states, the states can
be displayed via binary counting on only 2 LEDs (if only 2 are available).
The existing patterns are still used for 3 or 4 LEDs.
