Fixes are:
- Reset the module first before changing GPIO1 direction.
- Skip spurious bytes received after reset.
- Use HCI UART ID and baudrate when reinitializing UART.
- Disable all printf output which causes unit-tests to fail.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is a host driver for ESP32 chips running the esp-hosted firmware,
which turns ESP32s into a WLAN/BT co-processor.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This commit allows other ports to reuse the CYW43 HCI driver, by replacing
all Bluetooth UART and control named pins with defines in config files and
using `mpbthci` abstract functions (i.e. `mp_bluetooth_hci_*`) instead of
the STM32 specific UART functions.
Note: the function `cywbt_wait_cts_low` does not need to switch the CTS
pin from alternate function to GPIO to read it. At least on stm32, mimxrt
it's possible to just read the pin input. For example, see the STM32F7
RM0410 section 6.3.11, and the `SION` for IMXRT. So this function can
also be available for other ports if the pin mode switching is removed.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The QSPI driver provides the interface for using an on-board QSPI flash for
the filesystem. It provides the same methods as the driver for the
internal flash and uses the same name. Therefore, only one of the drivers
for internal flash, SPI flash and QSPI flash must be enabled at a time.
Signed-off-by: robert-hh <robert@hammelrath.com>
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes the signatures of QSPI write_cmd_data, write_cmd_addr_data and
read_cmd_qaddr_qdata so they return an error code. The softqspi and stm32
hardware qspi driver are updated to follow this new signature. Also the
spiflash driver is updated to use these new return values.
Signed-off-by: Damien George <damien@micropython.org>
Before this patch, WiFi connection was blocking, and could raise exceptions
if the connection failed for any reason (including timeouts). This doesn't
match the behavior of other WiFi modules, which connect asynchronously, and
requires handling of exceptions on connect. This change makes `connect()`
work asynchronously by scheduling code to poll connection status, and
handle reconnects (if needed), and return immediately without blocking.
Instead of being an explicit field, it's now a slot like all the other
methods.
This is a marginal code size improvement because most types have a make_new
(100/138 on PYBV11), however it improves consistency in how types are
declared, removing the special case for make_new.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Changes in this commit:
- Manifest include's now use the directory path where possible (no longer
necessary to include the manifest.py file explicitly).
- Add manifest.py for all drivers and components that are referenced by
port/board manifests.
- Replace all uses of freeze() with package()/module(), except for port and
board modules.
- Use opt=3 everywhere, for consistency and to reduce code size.
- Use require() instead of include() for all micropython-lib references.
- Remove support for optional board-level manifest.py in mimxrt port, to
make it behave the same as other ports (the board must set
FROZEN_MANIFEST to a custom manifest.py, which can optionally include the
default, port-level manifest).
- Also reinstates modules that were accidentally removed from the esp8266
512k build in fbe9417b90.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
Fixes:
- Should read `definitions` rather than `defintions`.
- Should read `resolution` rather than `resoultion`.
- Should read `inefficient` rather than `inefficent`.
- Should read `closed` rather than `closded`.
Signed-off-by: Tim Gates <tim.gates@iress.com>
1. Add -Wno-array-bounds to avoid false positive on gcc 12.1; see related
issue #8685.
2. Remove always-true not-NULL-check (Msg.Rsp.Args.Common.Bssid is an array
not a pointer).
3. Fix pointer-to-freed-stack in wlan_set_security.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Originally in drivers/ninaw10/nina_wifi_bsp.c but that isn't a QSTR source.
Also remove outdated commment about root pointers in mpconfigport.h.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This uses MP_REGISTER_ROOT_POINTER() to register mp_wifi_spi, mp_wifi_timer
and mp_wifi_sockpoll_list and removes the same from all mpconfigport.h.
Signed-off-by: David Lechner <david@pybricks.com>
For v2 cards that are standard capacity the read/write/erase commands take
byte address values. Use the result of CMD58 to distinguish SDSC from
SDHC/SDXC.
Signed-off-by: Damien George <damien@micropython.org>
For CSD v1.0 the computed size is in bytes, so convert it to number of
512-byte blocks, and then ioctl(4) will return the correct value.
Also implement ioctl(5) to return the block size, which is always 512.
Signed-off-by: Damien George <damien@micropython.org>
This codec is assembled for the MIMXRT1xxx_DEV boards and available for
WM8960 breakout boards as well.
The driver itself has been tested as working with the MIMXRT boards and a
Sparkfun WM6890 breakout board. It implements the initialization, basic
methods and some enhanced methods like 3D, ALC, soft-mute and deemphasis.
