PicoDVI in CP support 640x480 and 800x480 on Feather DVI, Pico and
Pico W. 1 and 2 bit grayscale are full resolution. 8 and 16 bit
color are half resolution.
Memory layout is modified to give the top most 4k of ram to the
second core. Its MPU is used to prevent flash access after startup.
The port saved word is moved to a watchdog scratch register so that
it doesn't get overwritten by other things in RAM.
Right align status bar and scroll area. This normally gives a few
pixels of padding on the left hand side and improves the odds it is
readable in a case. Fixes#7562
Fixes c stack checking. The length was correct but the top was being
set to the current stack pointer instead of the correct top.
Fixes#7643
This makes Bitmap subscr raise IndexError instead of ValueError
when the index arguments are wrong.
- define CIRCUITPY_BUILD_EXTENSIONS to predefined values
- set CIRCUITPY_BUILD_EXTENSIONS in port and board config
- reuse the support matrix "get_settings_from_makefile" to get it
- move the existing port and board specific values
- remove the C3 specific board values because it's not the default
- update build_release_files.py to use get_settings_from_makefile
.. and enable it on atmel-samd and raspberrypi. On trinket_m0 this saves
96 net bytes of flash. There are 216 bytes actually saved by reducing
the flash storage size of the property descriptors, but added code in
several paths takes back over half of the 'raw savings'.
By organizing the "get-only" and "get-set" (but no delete) properties
each in a different section, we can represent then more efficiently.
Testing performed: that a get-only property can still be gotten but
can't be set or deleted; that a get-set property can sill be gotten or
set but can't be deleted. Tested on pygamer.
Because this requires linker file support, I only enabled it on two of
the ports.
1. Check for correct error values from dma_claim_unused_channel.
2. Introduce a .stereo flag for simplicity.
3. Clarify PWM carrier frequency choice.
4. Start introducing quiescent audio value. Still need to ramp up/down.
5. Redo audio stop logic a bit.
6. Fix (unrelated) displayio dependency things.
There is still an interference problem between other DMA users and audio. Still debugging this.
This allows more options to be overridden to 0 in an mpconfigboard.mk.
Improved:
* FRAMEBUFFERIO, FULL_BUILD, BITOPS, PWMIO, RGBMATRIX, OTARYIO, PULSEIO, WATCHDOG
Still problematic (pull requests welcome):
* RP2PIO & NEOPIXEL_WRITE, possibly only if a status neopixel is defined
* BITBANGIO, possibly only if BUSIO is enabled
* RTC
Incidentally, with RP2PIO & NEOPIXEL_WRITE, BITBANGIO, and RTC re-enabled I get
```
323956 bytes used, 720524 bytes free in flash firmware space out of 1044480 bytes (1020.0kB).
12072 bytes used, 250072 bytes free in ram for stack and heap out of 262144 bytes (256.0kB).
```
Closes#4515
This switches stage2 to C and uses Jinja to change the C code based
on flash settings from https://github.com/adafruit/nvm.toml. It
produces the fastest settings for the given set of external flashes.
Flash size is no longer hard coded so switching flashes with similar
capabilities but different sizes should *just work*.
This PR also places "ITCM" code in RAM to save the XIP cache for
code execution. Further optimization is possible. A blink code.py
still requires a number of flash fetches every blink.
Fixes#4041
The rp2040 is _very_ marginal for mp3 playback, and currently sometimes triggers a bug that gives garbled audio output. However, it does work for some limited situations.
Any two consecutive pins can be used for an IncrementalEncoder
Testing performed: Put a synthesized (few hundred counts per second) quadrature signal into GP2/3 and read the encoder out. Performed filesystem operations at the same time to stress test it.
The reasons for not using common_hal_rp2pio_statemachine_readinto are commented on.
This adds I2SOut and PDMIn support via PIO.
StateMachines can now:
* read and read while writing
* transfer in 1, 2 or 4 byte increments
* init pins based on expected defaults automatically
* be stopped and restarted
* rxfifo can be cleared and rxstalls detected (good for tracking when
the reading code isn't keeping up)
Fixes#4162
