This patch makes pllvalues.py generate two tables: one for when HSI is used
and one for when HSE is used. The correct table is then selected at
compile time via the existing MICROPY_HW_CLK_USE_HSI.
When building with link time optimization enabled it is possible both
gc_collect() and gc_collect_regs_and_stack() get inlined into gc_alloc()
which can result in the regs variable being pushed on the stack earlier
than some of the registers. Depending on the calling convention, those
registers might however contain pointers to blocks which have just been
allocated in the caller of gc_alloc(). Then those pointers end up higher on
the stack than regs, aren't marked by gc_collect_root() and hence get
sweeped, even though they're still in use.
As reported in #4652 this happened for in 32-bit msvc release builds:
mp_lexer_new() does two consecutive allocations and the latter triggered a
gc_collect() which would sweep the memory of the first allocation again.
The machine.WDT() now accepts the "timeout" keyword argument to select the
WDT interval. And the WDT is changed to panic mode which means it will
reset the device if the interval expires (instead of just printing an error
message).
On the STM32F722 (at least, but STM32F767 is not affected) the CK48MSEL bit
must be deselected before PLLSAION is turned off, or else the 48MHz
peripherals (RNG, SDMMC, USB) may get stuck without a clock source.
In such "lock up" cases it seems that these peripherals are still being
clocked from the PLLSAI even though the CK48MSEL bit is turned off. A hard
reset does not get them out of this stuck state. Enabling the PLLSAI and
then disabling it does get them out. A test case to see this is:
import machine, pyb
for i in range(100):
machine.freq(122_000000)
machine.freq(120_000000)
print(i, [pyb.rng() for _ in range(4)])
On occasion the RNG will just return 0's, but will get fixed again on the
next loop (when PLLSAI is enabled by the change to a SYSCLK of 122MHz).
Fixes issue #4696.
The stm32 and nrf ports already had the behaviour that they would first
check if the script exists before executing it, and this patch makes all
other ports work the same way. This helps when developing apps because
it's hard to tell (when unconditionally trying to execute the scripts) if
the resulting OSError at boot up comes from missing boot.py or main.py, or
from some other error. And it's not really an error if these scripts don't
exist.
This patch makes the DAC driver simpler and removes the need for the ST
HAL. As part of it, new helper functions are added to the DMA driver,
which also use direct register access instead of the ST HAL.
Main changes to the DAC interface are:
- The DAC uPy object is no longer allocated dynamically on the heap,
rather it's statically allocated and the same object is retrieved for
subsequent uses of pyb.DAC(<id>). This allows to access the DAC objects
without resetting the DAC peripheral. It also means that the DAC is only
reset if explicitly passed initialisation parameters, like "bits" or
"buffering".
- The DAC.noise() and DAC.triangle() methods now output a signal which is
full scale (previously it was a fraction of the full output voltage).
- The DAC.write_timed() method is fixed so that it continues in the
background when another peripheral (eg SPI) uses the DMA (previously the
DAC would stop if another peripheral finished with the DMA and shut the
DMA peripheral off completely).
Based on the above, the following backwards incompatibilities are
introduced:
- pyb.DAC(id) will now only reset the DAC the first time it is called,
whereas previously each call to create a DAC object would reset the DAC.
To get the old behaviour pass the bits parameter like: pyb.DAC(id, bits).
- DAC.noise() and DAC.triangle() are now full scale. To get previous
behaviour (to change the amplitude and offset) write to the DAC_CR (MAMP
bits) and DAC_DHR12Rx registers manually.
If MICROPY_HW_RTC_USE_BYPASS is enabled the RTC startup goes as follows:
- RTC is started with LSE in bypass mode to begin with
- if that fails to start (after a given timeout) then LSE is reconfigured
in non-bypass
- if that fails to start then RTC is switched to LSI
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
These macros are unused, and they can conflict with other entities by the
same name. If needed they can be provided as static inline functions, or
just functions.
Fixes issue #4559.
Adds support for hardware i2c to the zephyr port. Similar to other ports
such as stm32 and nrf, we only implement the i2c protocol functions
(readfrom and writeto) and defer memory operations (readfrom_mem,
readfrom_mem_into, and writeto_mem) to the software i2c implementation.
This may need to change in the future because zephyr is considering
deprecating its i2c_transfer function in favor of i2c_write_read; in this
case we would probably want to implement the memory operations directly
using i2c_write_read.
Tested with the accelerometer on frdm_k64f and bbc_microbit boards.
For gpio_hold_en() to work properly (not draw additional current) pull
up/down must be disabled when hold is enabled. This patch makes sure this
is the case by reworking the pull constants to be a bit mask.
Adding section about on how to disable use of the linker flag
-flto, by setting the LTO=0 argument to Make. Also, added a
note on recommended toolchains to use that works well with
LTO enabled.
Removing linker script for nrf52840 s140 v6.0.0 as pca10056
target board now points to the new v6.1.1. Also, removing the
entry from the download_ble_stack.sh script.
Removing linker script for nrf52832 s132 v6.0.0 as all target
boards now points to the new v6.1.1. Also, removing the entry
from the download_ble_stack.sh script.
Previously specifying None as the pull value would leave the pull up/down
state unchanged. This change makes it so -1 leaves the state unchanged and
None makes the pin float, as per the docs.
In this port JavaScript is the underlying "machine" and MicroPython is
transmuted into JavaScript by Emscripten. MicroPython can then run under
Node.js or in the browser.
Functions in these files may be needed when certain features are enabled
(eg dual core mode), even if the linker does not give a warning or error
about unresolved symbols.
During make, makemoduledefs.py parses the current builds c files for
MP_REGISTER_MODULE(module_name, obj_module, enabled_define)
These are used to generate a header with the required entries for
"mp_rom_map_elem_t mp_builtin_module_table[]" in py/objmodule.c
To use HSI instead of HSE define MICROPY_HW_CLK_USE_HSI as 1 in the board
configuration file. The default is to use HSE.
HSI has been made the default for the NUCLEO_F401RE board to serve as an
example, and because early revisions of this board need a hardware
modification to get HSE working.
This demonstrates how to use external QSPI flash in XIP (execute in place)
mode. The default configuration has all extmod/ code placed into external
QSPI flash, but other code can easily be put there by modifying the custom
f769_qspi.ld script.
A board can now use the make variables TEXT0_SECTIONS and TEXT1_SECTIONS to
specify the linker sections that should go in its firmware. Defaults are
provided which give the existing behaviour.
esp_wifi_connect will return ESP_OK for the normal path of execution which
just means the reconnect is started, not that it is actually reconnected.
In such a case wifi.isconnected() should return False until the
reconnection is complete. After reconnect a GOT_IP event is called and it
will change wifi_sta_connected back to True.
This patch makes sure that the char_data.props is first
assigned a value before other flags are OR'd in.
Resolves compilation warning on possible unitialized variable.
This patch makes sure that advertisment data is located in
persistent static RAM memory throughout the advertisment.
Also, setting m_adv_handle to predifined
BLE_GAP_ADV_SET_HANDLE_NOT_SET value to indicate first time
usage of the handle. Upon first advertisment configuration
this will be populated with a handle value returned by the
stack (s132/s140).
After new layout of nordicsemi.com the direct links to
command line tools (nrfjprog) has changed to become dynamic.
This patch removes the old direct links to each specific OS
variant and is replaced with one single link to the download
landing page instead.
Currently all usages of mp_hal_pin_config_alt_static() set the pin speed to
"high" (50Mhz). The SDRAM interface typically runs much faster than this
so should be set to the maximum pin speed.
This commit adds mp_hal_pin_config_alt_static_speed() which allows setting
the pin speed along with the other alternate function details.
A few RTC constants weren't being parsed properly due to whitespace
differences, and this patch makes certain whitespace optional. Changes
made:
- allow for no space between /*!< and EXTI, eg for:
__IO uint32_t IMR; /*!<EXTI Interrupt mask register, Address offset: 0x00 */
- allow for no space between semicolon and start of comment, eg for:
__IO uint32_t ALRMASSR;/*!< RTC alarm A sub second register, Address offset: 0x44 */
As mentioned in #4450, `websocket` was experimental with a single intended
user, `webrepl`. Therefore, we'll make this change without a weak
link `websocket` -> `uwebsocket`.
If opening of /dev/mem has failed an `OSError` is appropriately raised, but
the next time `mem8/16/32` is accessed the invalid file descriptor is used
and the program gets a SIGSEGV.
Replaces "PYB: soft reboot" with "MPY: soft reboot", etc.
Having a consistent prefix across ports reduces the difference between
ports, which is a general goal. And this change won't break pyboard.py
because that tool only looks for "soft reboot".
Adds support for 3 Cortex-M boards, selectable via "BOARD" in the Makefile:
- microbit, Cortex-M0 via nRF51822
- netduino2, Cortex-M3 via STM32F205
- mps2-an385, Cortex-M3 via FPGA
netduino2 is the default board because it's supported by older qemu
versions (down to at least 2.5.0).
Instead of checking each callback (currently storage and dma) explicitly
for each SysTick IRQ, use a simple circular function table indexed by the
lower bits of the millisecond tick counter. This allows callbacks to be
easily enabled/disabled at runtime, and scales well to a large number of
callbacks.
