Commit Graph

14 Commits

Author SHA1 Message Date
Scott Shawcroft cebcec5e63 Check for floating pins by pulling them low briefly before testing their values. 2018-03-26 16:32:16 -07:00
Scott Shawcroft 25ba8ee489 Add an s because grammar. 2018-03-26 15:21:08 -07:00
Scott Shawcroft 37538fc0e7 Fix I2C init hang when the SCL pin is pulled low.
We added a check to make sure the pins are in a high state before
initing the bus. This leads to a friendly error message when someone
forgets to add the pull up resistors to their circuit.
2018-03-26 15:13:52 -07:00
Jeff Epler dddfad6594 UART: Fix maybe-uninitialized diagnostic
The following error occurs when building with gcc 5.4.1 (debian stretch):

common-hal/busio/UART.c:104:83: error: 'sercom_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
                   sercom_insts[rx->sercom[j].index]->USART.CTRLA.bit.ENABLE == 0) ||

It may be related to the addition of rx-only UARTs; gcc is unable
to infer the intended relationship between have_tx and sercom_index
being set (I am still not entirely confident of it myself)
2018-03-19 20:40:04 -05:00
Scott Shawcroft 88aa0e2660 Remove SERCOM pointers from pin data structure because index is
enough.

This saves 380 bytes on the Arduino Zero build. (More pins ==
more savings.)
2018-03-14 11:14:32 -07:00
Scott Shawcroft e7fc0b6aa7 Use DMA for long SPI transactions including those to the SPI Flash.
QSPI is not currently working so its commented out.

This is progress on #652.
2018-03-09 12:45:46 -08:00
Bryan Siepert 942b7ffbe0 fixes hardware dotstar support for 3.0 and addresses issue #514 2018-03-08 20:39:47 -08:00
Dan Halbert 9b4477e1dc Implement UART for 3.0 + related fixes.
1. UART: ported to ASF4. Allow rx-only and tx-only. Add .baudrate r/w property.

2. Make NeoPixel timing deterministic by turning off caches during NeoPixel writes.
3. Incorporate asf4 updates:
  a. async USART driver
  b. bringing Atmel START configuration closer to what we use
  c. Clock initialization order now specified by CIRCUITPY_GCLK_INIT_1ST and _LAST.
4. supervisor/port.c: Move commented-out clock-test pin setting to correct location.
2018-02-21 17:18:49 -05:00
Dan Halbert e550b024c5 atmel-samd: Correct computation of SPI baud rate.
all: Add .frequency read-only property for busio.SPI to return actual frequency.

Fix esp8266/posix_helpers.c, which was not up to date for the new
long-lived/short-lived heap allocation scheme.
2018-01-30 12:08:41 -05:00
Dan Halbert 065e82015f merge from 2.2.0 + fix up board defs 2018-01-02 21:25:41 -05:00
Dan Halbert 72c911be97 Support SPI flash chips for CIRCUITPY, using non-DMA SPI for now. 2017-11-27 21:00:24 -05:00
Dan Halbert 312444bbd2 non-DMA SPI working; adding this now for testing; will continue with DMA
Also, fixed pin mappings for rev B Metro M4:
swap PA12 and PA13 on SPI 2x3 header
swap A3 and A5

Comment out all frozen modules in CPX again to make room while waiting
for SPI flash.
2017-11-16 19:09:35 -05:00
Dan Halbert 7292984204 Implement busio.I2c.
* Added asf4_conf/samd*/hpl_sercom_config.h
* Adjusted clocks in peripheral_clk_config.h.
* Put some frozen libs back in CPX for testing.
* Implement common-hal I2C
* Add samd*_peripherals.h in parallel with samd*_pins.h for common
  functions and data.
* Store SERCOM index in pins table for convenience.
* Canonicalize some #include guard names in various .h files.

simpler reset of SERCOMs; remove unused routine
2017-11-07 09:59:54 -08:00
Scott Shawcroft 73c15dcf8b Merge commit 'f869d6b2e339c04469c6c9ea3fb2fabd7bbb2d8c' into nrf2_merge
This is prep for merging in the NRF5 pull request.
2017-10-24 22:31:16 -07:00