- Add board.md files for MIMXRT1060_EVK and MIMXRT1064_EVK warning about
their experimental state.
- Add separate deploy_teensy.md and deploy_mimxrt.md files.
The ARCH MIX board exposes the Ethernet Pins at it's connectors. Therefore
the software is configured for using a LAN8720 PHY device. Breakout boards
with the LAN8720 are easily available.
This commit adds I2S protocol support for the rp2 port:
- I2S API is consistent with STM32 and ESP32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- DMA IRQs are managed on an I2S object basis, allowing other
RP2 entities to use DMA IRQs when I2S is not being used
- MicroPython documentation
- tested on Raspberry Pi Pico development board
- build metric changes for this commit: text(+4552), data(0), bss(+8)
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
Eliminate noise data from being sent to the I2S peripheral when the
transmitted sample stream is stopped.
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
Now that there are feature levels, and that this port uses
MICROPY_CONFIG_ROM_LEVEL_MINIMUM, it's easy to see what optional features
can be disabled. And this commit disables them.
Signed-off-by: Damien George <damien@micropython.org>
Word-size specific configuration is now done automatically, so it no longer
requires this to match the ARM configuration.
Also it's less common to have 32-bit compilation support installed, so this
will make it work "out of the box" for more people.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This makes it possible for cooperative multitasking systems to keep running
event loops during garbage collector operations.
For example, this can be used to ensure that a motor control loop runs
approximately each 5 ms. Without this hook, the loop time can jump to
about 15 ms.
Addresses #3475.
Signed-off-by: Laurens Valk <laurens@pybricks.com>
This is an stm32-specific feature that's accessed via the pyb module, so
not something that will be widely enabled.
Signed-off-by: Damien George <damien@micropython.org>
This commit is a no-op change. Future improvements can come from making
individual boards use CORE or BASIC.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Some of these will later be moved to CORE or BASIC, but EXTRA is a good
starting point based on what stm32 uses.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prior to this commit IRQs on STM32F4 could be lost because SR is cleared by
reading SR then reading DR. For example, if both RXNE and IDLE IRQs were
active upon entry to the IRQ handler, then IDLE is lost because the code
that handles RXNE comes first and accidentally clears SR (by reading SR
then DR to get the incoming character).
This commit fixes this problem by making the IRQ handler more atomic in the
following operations:
- get current IRQ status flags
- deal with RX character
- clear remaining status flags
- call user handler
On the STM32F4 it's very hard to get this right because the only way to
clear IRQ status flags is to read SR then DR, but the read of DR may read
some data which should remain in the register until the user wants to read
it. And it won't work to cache the read because RTS/CTS flow control will
then not work. So instead the new code disables interrupts if the DR is
full and waits for the user to read it before reenabling the interrupts.
Fixes issue mentioned in #4599 and #6082.
Signed-off-by: Damien George <damien@micropython.org>
Following on from ba940250a5, the change here
makes output about 15 times faster (now up to about 550 kbytes/sec).
tinyusb_cdcacm_write_queue will return the number of bytes written, so
there's no need to use tud_cdc_n_write_available.
Signed-off-by: Damien George <damien@micropython.org>
This will be used by https://micropython.org/download/ to generate the
full listing of boards and firmware files.
Optionally supports a board.md for additional customisation of the
download page, as well as deploy.md for flashing instructions.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
We're using the MicroPython fork of NimBLE, which on the
`micropython_1_4_0` branch re-adds support for 64-bit targets and fixes
initialisation of g_msys_pool_list.
Also updates modbluetooth_nimble.c to suit v1.4.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
There is no release of IDF v4.4 yet but master is now on v5.0-dev so a
specific commit must be chosen to stick to v4.4.
Signed-off-by: Damien George <damien@micropython.org>
By moving code to ITCM, like vm, gc, parse, runtime. The change affects
mostly the execution speed of MicroPython code. The speed is increased by
up to a factor of 6, especially for MCU with small cache.
Prior to this commit mp_hal_ticks_cpu() was not started properly. It only
started when the code was executed with a debugger attached, except for the
Teensy (i.MXRT1062) boards. As an additional fix, the CYYCNT timer is now
started at boot time.
Also rename mp_hal_ticks_cpu_init() to mp_hal_ticks_cpu_enable().
