Add address_little_endian for epaper displays with little endian
(low byte first) addresses.
Also clears allocated display and display bus memory so it has a
known state. The acep member wasn't always set so it varied
accidentally.
Fixes#7560. May fix#7778. Fixes#5119.
This 2-in-1 PR started with the goal of support the Bangle.js 2
smartwatch with *no USB*.
* Adds "secure" DFU build support with a committed private key.
* Adds 3-bit color support with one dummy bit for the JDI memory display
* Allows nrf boards to have a board_background_task() run in RUN_BACKGROUND_TASK.
This is needed because the Bangle.js 2 uses the watchdog to reset.
* Renamed port_background_task() to port_background_tick() to indicate it
runs on tick, not RUN_BACKGROUND_TASK.
* Marks serial connected when the display terminal is inited. This means
that safe mode messages show up on the display.
ACep, 7-color epaper displays also pack 3 bits in 4. So, I added that
support as well.
* Adds 3-bit ACeP color support for 7-color e-paper displays. (Not
watch related but similar due to color depth.)
* Allows a refresh sequence instead of a single int command. The 7" ACeP
display requires a data byte for refresh.
* Adds optional delay after resetting the display. The ACeP displays
need this. (Probably to load LUTs from flash.)
* Adds a cleaning phase for ACeP displays before the real refresh.
For both:
* Add dither support to Palette.
* Palette no longer converts colors when set. Instead, it caches
converted colors at each index.
* ColorConverter now caches the last converted color. It should make
conversions faster for repeated colors (not dithering.)
This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
This also improves Palette so it stores the original RGB888 colors.
Lastly, it adds I2CDisplay as a display bus to talk over I2C. Particularly
useful for the SSD1306.
Fixes#1828. Fixes#1956
This fixes the bug that bitmap changes do not cause screen updates
and optimizes the refresh when the bitmap is simply shown on the
screen. If the bitmap is used in tiles, then changing it will
cause all TileGrids using it to do a full refresh.
Fixes#1981
Different operations to the display tree have different costs. Be
aware of these costs when optimizing your code.
* Changing tiles indices in a TileGrid will update an area
covering them all.
* Changing a palette will refresh every object that references it.
* Moving a TileGrid will update both where it was and where it moved to.
* Adding something to a Group will refresh each individual area it
covers.
* Removing things from a Group will refresh one area that covers all
previous locations. (Not separate areas like add.)
* Setting a new top level Group will refresh the entire display.
Only TileGrid moves are optimized for overlap. All other overlaps
cause sending of duplicate pixels.
This also adds flip_x, flip_y and transpose_xy to TileGrid. They
change the direction of the pixels but not the location.
Fixes#1169. Fixes#1705. Fixes#1923.
foamyguy
Scott Shawcroft
Timon
gamblor21
Jeff Epler
Tsutomu IKEGAMI
Kevin Matocha
microDev
Dan Halbert
Diego Elio Pettenò
Scott Shawcroft
Matthew Newberg