This also removes the need to pin share because we don't use the
status LED while user code is running.
The status flashes fallback to the HW_STATUS LED if no RGB LED is
present. Each status has a unique blink pattern as well.
One caveat is the REPL state. In order to not pin share, we set the
RGB color once. PWM and single color will be shutoff immediately but
DotStars and NeoPixels will hold the color until the user overrides
it.
Fixes#4133
In #4683, tannewt noticed that uncrustify was not running on some
file in common-hal.
I investigated and found that it was not being run on a bunch of paths.
Rather than make incremental changes, I rewrote list_files to work
bsaed on regular expressions; these regular expressions are created from
the same git-style glob patterns.
I spot-checked some specific filenames after this change, and all looks good:
```
$ python3 tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
tools/codeformat.py -v --dry-run tests/basics/int_small.py ports/raspberrypi/common-hal/pulseio/PulseIn.c extmod/virtpin.c tests/thread/thread_exit1.py ports/raspberrypi/background.h extmod/re1.5/recursiveloop.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup extmod/virtpin.c ports/raspberrypi/background.h ports/raspberrypi/common-hal/pulseio/PulseIn.c
black --fast --line-length=99 -v tests/thread/thread_exit1.py
```
recursiveloop and int_small are excluded, while PulseIn, virtpin,
and background are included.
Testing running from a subdirectory (not _specifically_ supported though):
```
(cd ports && python3 ../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c)
../tools/codeformat.py -v --dry-run raspberrypi/common-hal/pulseio/PulseIn.c ../extmod/virtpin.c
uncrustify -c /home/jepler/src/circuitpython/tools/uncrustify.cfg -lC --no-backup ../extmod/virtpin.c raspberrypi/common-hal/pulseio/PulseIn.
```
As a side-effect, a bunch more files are re-formatted now. :-P
After this change, the following program works for me on the MIMXRT1010-EVK:
```python
import pwmio
import board
p = pwmio.PWMOut(board.D13, frequency=1_000_000, variable_frequency=True)
p.duty_cycle = 32868
while True:
pass
```
Querying and varying the duty_cycle and frequency work as well.
The lowest frequency obtainable is about 2kHz; there is an additional
divider which would allow lower PWM frequencies (I think 1kHz is important
for servos?)
Something odd happens with very low duty cycles, such as
```python
>>> p.frequency = 2000
>>> p.duty_cycle = 2
```
instead of a symmetrical waveform, it's asymmetrical. With `duty_cycle=4`,
the effect disappears. The reason for this is probably hidden in the
datasheet, but could affect servos or other things that count pulse
widths.
Set the betweenTransferDelay to the SCK low-time, to avoid long pauses
between bytes (transfers) while preventing the last SCK cycle in a byte
from being a runt pulse.
Compared to an earlier revision of this change, which just set the delays
all to zero, this doesn't break using an AirLift, which was sensitive
to the runt pulses (the simple loopback-wire test didn't detect the problem)
without this, the baud rate could be wrong; in my testing, it was
low by a factor of 2 when requesating baudrate=1_000_000 (1MHz).
When passing the baudrate in to LPSPI_MasterInit, the setting is made
automatically, but LPSPI_MAster_SetBaudRate just returns it via the
out-parameter tcrPrescaleValue.
There are DNP resistors on the MIMXRT1010-EVK board (see SCH-45852)
that lead to these pins on the arduino-style header not being connected
through. In theory someone could populate them, but as it the presence
of these names in the pins module caused problems when they didn't work
as expected.
Closes#3012
Scott Shawcroft
Kattni Rembor
Dan Halbert
Jeff Epler
Jeff Epler
Jeff Epler
gamblor21
Mark
microDev
James Bowman
Philip Jander
BiffoBear
Dan Halbert