f7303e6bd0
Merge pull request #2754 from maholli/non-standard-nvm
...
Add non-standard nvm to QSPI for external flash support
2020-05-12 11:56:33 -07:00
62bdfb74e3
removed lib from catwan_usbstick - updated transalations overflowed
2020-05-12 16:40:23 +10:00
5e5461e77e
removed countio from catwan_usbstick build
2020-05-12 16:32:35 +10:00
ee2cb703c8
merged master
2020-05-12 14:41:28 +10:00
ffaeeda749
nrf: simmel: decrease flash filesystem size
...
The flash filesystem must be reduced in order to allow the current
build to fit.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-12 09:31:51 +08:00
f7fcd43516
nrf: simmel: disable SPIM3
...
Disable the SPIM3 controller to avoid needing to dedicate 8 kB to
the SPIM3 block.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-12 09:31:51 +08:00
370fc7293a
nrf: support disabling SPIM3
...
SPIM3 is faster than all other SPI blocks, and is capable of generating
a 32 MHz clock. However, it cannot be used at the same time as the BLE
radio without dedicating an additional 8 kB of RAM to it.
Therefore, some boards may want to disable this. Support pre-defining
NRFX_SPIM3_ENABLED on the command line to disable it on some bords.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-12 09:31:51 +08:00
79c055f958
nrf: simmel: enable aesio
...
This adds AES support to simmel.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-12 09:31:51 +08:00
235098efb8
nrf: simmel: correct CSn pin
...
The CSn pin is pin 6 on bank 1, not bank 0.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-12 09:31:51 +08:00
62b835ad76
Merge pull request #2833 from xiongyihui/pitaya-go
...
add nRF52840 based Makerdiary Pitaya Go
2020-05-11 16:34:27 -07:00
4937d5f1ca
Merge pull request #2866 from hierophect/stm32-lsetimeout
...
STM32: Fix LSE hang at startup
2020-05-11 16:23:09 -07:00
55f78bfb70
Merge pull request #2878 from WarriorOfWire/ujson-stream-protocol
...
ujson: work with mp stream protocol for fast & easy read
2020-05-11 15:40:27 -07:00
801d9655e5
Merge pull request #2881 from DavePutz/Issue2872
...
Added call to rtc_reset() to fix Issue #2872
2020-05-11 15:30:32 -07:00
94949fb46f
Add recovery domain write access, adjust stack
2020-05-11 18:02:40 -04:00
61450cbd56
Add Teensy 4.1 board definition
2020-05-11 13:58:58 -07:00
248704b262
Merge remote-tracking branch 'upstream/master' into stm32-lsetimeout
2020-05-11 14:18:37 -04:00
407938bf3a
Added a check for platforms supporting RTC before calling rtc_reset()
...
Added an #if CIRCUITPY_RTC check for platforms supporting RTC
2020-05-11 12:03:44 -05:00
2ddfab315c
Added call to rtc_reset() in rtc_init()
...
Fix for issue #2872 . The rtc_time_source had not been initialized; causing a time.time() call to fail.
2020-05-11 11:31:18 -05:00
eb3d5fa453
ujson: do not eat trailing whitespace
...
Ujson should only worry about whitespace before JSON. This becomes apparent when you are using MP stream protocol to read directly from input buffers.
When you attempt to read(1) on a UART (and possibly other protocols) you have to wait for either the byte or the timeout.
Fixes:
- Waiting for a timeout after you have completed reading a correct and complete JSON off the input.
- Raising an OSError after reading a correct and complete JSON off the input.
- Eating more data than semantically owned off the input buffer.
- Blocking to start parsing JSON until the entire JSON body has been loaded into a potentially large, contiguous Python object.
Code you would write before:
```
line = board_busio_uart_port.read_line()
json_dict = json.loads(line)
```
or reaching for fixed buffers and swapping them around in Python.
Code that did not work before that does now:
```
json_dict = json.load(board_busio_uart_port)
```
- This removes the need for intermediate copies of data when reading JSON from micropython stream protocol inputs.
- It also increases total application speed by parsing JSON concurrently with receiving on boards that read from UART via DMA.
- It simplifies code that users write while improving their apps.
2020-05-10 20:45:42 -07:00
206d0e598a
Add vectorio: for drawing shapes
...
vectorio builds on m4 express feather
Concrete shapes are composed into a VectorShape which is put into a displayio Group for display.
VectorShape provides transpose and x/y positioning for shape implementations.
Included Shapes:
* Circle
- A radius; Circle is positioned at its axis in the VectorShape.
- You can freely modify the radius to grow and shrink the circle in-place.
* Polygon
- An ordered list of points.
- Beteween each successive point an edge is inferred. A final edge closing the shape is inferred between the last
point and the first point.
- You can modify the points in a Polygon. The points' coordinate system is relative to (0, 0) so if you'd like a
top-center justified 10x20 rectangle you can do points [(-5, 0), (5, 0), (5, 20), (0, 20)] and your VectorShape
x and y properties will position the rectangle relative to its top center point
* Rectangle
A width and a height.
2020-05-09 15:38:22 -07:00
e6df8e0989
Merge branch 'master' into non-standard-nvm
2020-05-09 12:22:50 -07:00
8d00d99ca0
Shrink hallowing_m0_express to fit ko build
2020-05-08 22:51:21 -04:00
5249a7b02c
Add timeout and adjustment to LSI
2020-05-08 12:36:39 -04:00
182ae10080
Fix build after #2831 (stm32f4xx rgbmatrix) broke it
2020-05-07 18:32:50 -05:00
c3b3eb4c21
Merge pull request #2831 from jepler/rgbmatrix-stm
...
stm: enable RGBMatrix
2020-05-06 08:35:25 -07:00
4519ddebeb
Merge pull request #2841 from hierophect/mimxrt-spi-oneway
...
mimxrt10xx: add one-directional SPI
2020-05-06 08:32:21 -07:00
7f1be814c8
changed build variables as per advice
2020-05-06 09:04:15 +10:00
a1330747e8
text fixes, postpone warning disable
2020-05-05 12:46:30 -04:00
c311b5c002
Merge pull request #2842 from hierophect/stm32-h7-displayio
...
STM32: Add displayio to F7/H7
2020-05-05 12:37:08 -04:00
f63ee9fb9b
excluded countio from other smaller boards
2020-05-05 16:15:57 +10:00
d5c24b99b8
hallowing m0 - exclude countio
2020-05-05 16:04:28 +10:00
bfa5cd9c13
refactor countio based on feedback
2020-05-05 15:23:38 +10:00
b7836aeac6
address review comments
2020-05-04 19:51:08 -04:00
bae7a5e433
make translate again
2020-05-04 17:26:59 -04:00
602eabe668
Squeeze hallowing_m0_express build slightly
...
ko build is a little too big.
2020-05-04 17:18:53 -04:00
c377d4bea7
Merge branch 'master' into non-standard-nvm
2020-05-04 16:08:45 -04:00
d6c6f9f4f0
add PacketBuffer .incoming_ and .outgoing_packet_length
2020-05-04 15:59:45 -04:00
4d7e341e44
Merge pull request #2844 from xobs/add-nrf-pca10100
...
nrf: add pca10100
2020-05-04 10:51:01 -04:00
b128399d1e
nrf: simmel: enable CIRCUITPY_USB_HID
...
Simmel had USB HID disabled in order to save space. However, the board
configuration did not set USB_DEVICES, causing it to inherit the default
device bouquet of MSC,CDC,MIDI,HID. This in turn caused HID to be included
in the USB Configuration Descriptor.
For some reason, this was not a problem in an earlier version of tinyusb or
circuitpython. However, in the most recent version this has rightfully
caused asserts to appear during configuration.
Re-enable USB_HID for now, as it doesn't add too much in terms of space.
We may disable it again later on if we become pressed for space.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-04 15:37:53 +08:00
cb4fc894d7
nrf: add pca10100
...
This is the nRF52833-DK board.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-05-04 15:07:49 +08:00
61b0994631
Fix flag typo
2020-05-01 14:46:06 -04:00
bc581fbdfb
Add-unidirectional-SPI
2020-05-01 13:15:38 -04:00
7dd3ddc06b
use Nordic's VID which seems to be allowed
...
https://devzone.nordicsemi.com/f/nordic-q-a/50638/usb-pid-for-nrf52840
2020-05-01 06:10:43 +00:00
a863b0a349
Fix openmv_h7 build
2020-04-30 13:46:12 -07:00
1ca90572f1
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-04-30 13:25:31 -07:00
10c5bf666e
Merge pull request #2836 from hierophect/stm32-openmv-pid
...
STM32: Add correct PID for the OpenMV
2020-04-30 16:07:34 -04:00
06b62721b3
Increase H7 filesystem size
2020-04-30 15:49:17 -04:00
74a2d0944a
Merge pull request #2834 from Teknikio/fix/bluebird_pinout
...
Update teknikio bluebird pin assignments
2020-04-30 11:50:02 -07:00
435aa3d055
Add correct PID for the OpenMV
2020-04-30 14:49:47 -04:00
4f71bd295d
Make PulseIO optional within DisplayIO
2020-04-30 14:47:50 -04:00
f44e1d6a8d
Merge pull request #2828 from simmel-project/add-simmel
...
WIP: add simmel board
2020-04-30 11:40:34 -07:00
89ff5589c4
Add the OpenMV-H7 R1 board
2020-04-30 12:39:20 -04:00
e5be728c1c
stm: enable protomatter
...
Testing performed: on stm32f405 feather, all pins change in plausible ways
on a logic probe. Didn't actually drive a display yet.
2020-04-30 08:58:58 -05:00
36a71560c2
update teknikio bluebird pin assignments
2020-04-30 09:58:27 -04:00
4393a88fb6
add nRF52840 based Makerdiary Pitaya Go
2020-04-30 07:38:20 +00:00
241d7e2ae6
change many ifndefs to ?=
2020-04-29 23:31:34 -04:00
f3078511a6
further cleanup and bug fixing
2020-04-29 23:18:08 -04:00
6aac9233db
nrf: bluetooth: add s147 v7.0.1 softdevice hexfile
...
This was not added as part of the initial v7.0.1 patchset because
.hex files are in this project's .gitignore, and so git ignored it.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-30 10:43:46 +08:00
180f5c6a94
Merge remote-tracking branch 'adafruit/master' into ringbuf-fixes
2020-04-29 22:11:22 -04:00
3d62f87e29
back to '.packet_size' for compatiblity
2020-04-29 22:10:56 -04:00
84cee1ab8d
rename and improve PacketBuffer packet length property
2020-04-29 17:49:31 -04:00
3799c34564
Disable bitbangio on CPX Crickit so we have room for lower_power.
...
Enable pixelbuf in its place because we'll need it soon.
2020-04-29 13:57:09 -07:00
a30ff70b4e
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-04-29 10:51:21 -07:00
1d0781bf12
nrf: add simmel board
...
This adds support for Simmel, an nRF52833-based bluetooth tracking
board designed to aid in pandemic tracing.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-29 11:40:00 +08:00
2d7cf4b792
Merge pull request #2819 from hierophect/stm32-readme
...
STM32: Add port readme, make flash
2020-04-28 12:32:03 -07:00
b2de5a9df9
fixing my goofy gcc-arm local stuff
2020-04-28 12:24:10 -07:00
6c4decd4e2
decoupling chip specific functions from EXTERNAL_FLASH_QSPI_SINGLE
2020-04-28 11:51:07 -07:00
baad9c11df
Merge branch 'master' into non-standard-nvm_cleanup
2020-04-28 11:42:58 -07:00
b9e494b85a
add submodule to TG-Watch02A
2020-04-28 00:03:02 -04:00
b7804f450b
Fix stm32746g_discovery
...
Also, rename it so that matches the other board names.
2020-04-27 20:34:42 -07:00
e45de39998
Fix nucleo_f746zg build
2020-04-27 20:28:05 -07:00
76b466a38a
add submodule to TG-Watch02A
2020-04-27 22:49:30 -04:00
2a0e176a77
Add readme and dfu-flashing
2020-04-27 20:51:47 -04:00
de42e4af02
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-04-27 17:43:32 -07:00
40a1f3edbc
Merge pull request #2811 from jepler/update-ulab
...
ulab: actually update the submodule
2020-04-27 17:41:43 -07:00
755d404edf
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-04-27 16:45:10 -07:00
faa50df05f
Merge pull request #2817 from jepler/stm-linker-scripts
...
Standardize on FLASH_FIRMWARE section name in linker scripts
2020-04-27 18:43:26 -04:00
7f0f0b30d3
linker scripts: Re-align at ":"
...
With "git show -b" you can verify that this is a whitespace only change
because the diff will be empty.
2020-04-27 17:17:42 -05:00
86943ca8a1
Merge remote-tracking branch 'adafruit/master'
2020-04-27 13:51:51 -07:00
7eff89e9f9
linker scripts: Re-align at ":"
...
With "git show -b" you can verify that this is a whitespace only change
because the diff will be empty.
2020-04-27 12:47:52 -05:00
d9e4155815
Merge branch 'master' into stm32f7_os
2020-04-27 12:58:15 -04:00
31d8e46063
Enables os on STM32F7
...
os.uname() works
os.urandom() doesn't work yet, will enable in another PR
2020-04-27 18:18:43 +02:00
f9096d83ac
Enables PulseIO on STM32F7
...
Tested on nucleo_f746zg
2020-04-27 17:55:07 +02:00
6f6dc835d2
litex: Use FLASH_FIRMWARE instead of FLASH in linker scripts
...
for compatibility with the build_memory_info script
2020-04-27 09:12:45 -05:00
808b456927
mimxrt10xx: Use FLASH_FIRMWARE instead of FLASH_TEXT in linker scripts
...
for compatibility with the build_memory_info script
This change was scripted:
git grep -l FLASH_TEXT | xargs sed -i s/FLASH_TEXT/FLASH_FIRMWARE/
2020-04-27 08:07:47 -05:00
aff42defda
stm: Use FLASH_FIRMWARE instead of FLASH_TEXT in linker scripts
...
for compatibility with the build_memory_info script
This change was scripted:
git grep -l FLASH_TEXT | xargs sed -i s/FLASH_TEXT/FLASH_FIRMWARE/
2020-04-27 08:07:28 -05:00
485f667141
ulab: disable on espruino pico
...
this non-"express" board is nearly full. Right now it's actually possible
just to disable the "compare" module, but as this leaves it packed
pretty full I prefer to fully disable it in order to avoid the topic
returning again soon.
2020-04-27 07:47:05 -05:00
9e4b94f466
Merge pull request #2805 from tannewt/update_tinyusb
...
Update tinyusb
2020-04-26 20:55:36 -07:00
652a5de242
Merge pull request #2809 from k0d/stm32f767xx_fix
...
Adds missing declarations in periph.h for stm32f767xx
2020-04-25 14:16:34 -04:00
8814dd038e
Adds missing declarations in periph.h for stm32f767xx
2020-04-25 19:50:48 +02:00
67c053e9c4
Add USB include for LiteX
2020-04-24 17:24:05 -07:00
5c7f6e6211
Remove empty #if and add missing includes.
2020-04-24 11:48:55 -07:00
91fbbcab19
adds support for the stm32f746g_disco board
2020-04-24 16:43:39 +02:00
5a22a5d016
Merge pull request #2598 from hierophect/stm32-docfix
...
Add stm to docs matrix
2020-04-24 10:07:15 -04:00
982a755eae
Merge pull request #2801 from simmel-project/nrf-s140-7.0.1
...
Add NRF S140 7.0.1
2020-04-23 21:59:51 -04:00
bd0df9e3bc
Minor redundancy fix
2020-04-23 17:43:35 -04:00
c6c77726e7
Merge remote-tracking branch 'upstream/master' into stm32-docfix
2020-04-23 13:39:48 -04:00
8791ca6af3
implement requested changes
2020-04-23 13:33:41 -04:00
ead7c6c887
Merge pull request #2785 from k0d/ports_nucleo_f746zg
...
STM32: adds support for stm32f746xx MCU and the nucleo_f746zg board
2020-04-23 12:32:44 -04:00
83cc9783cc
STM32: adds support for stm32f746xx MCU and the nucleo_f746zg board
2020-04-23 10:48:27 +02:00
f13de32208
Add HSE_VALUE for STM feather.
2020-04-22 14:37:24 -07:00
d0a2106547
Remove old build flags, add fixes for shared_matrix
2020-04-22 16:06:08 -04:00
b277944cf0
Fix STM so it matches the correct RTC fields.
2020-04-22 11:10:51 -07:00
689dd61379
nrf: nrf52833: use s140 v7.0.1
...
Previously, we were using v6.1.1 which worked, but was unsupported.
v7.0.1 is the first version of s140 that supports the nRF52833.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-22 13:34:11 +08:00
09bef7b0e1
nrf: bluetooth: add s140 v7.0.1
...
This is the first version with official support for nRF52833.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-22 13:33:39 +08:00
2f86e31501
fix calculation of nrf firmware size
2020-04-22 00:52:54 -04:00
fbc8719fad
ringbuf tested
2020-04-21 22:40:12 -04:00
77cd93ac2d
merge from adafruit
2020-04-21 17:47:51 -04:00
38ec3bc574
further ringbuf cleanup
2020-04-21 17:38:20 -04:00
dcb0e50f04
Fix USB midi and hid disable.
2020-04-21 14:15:44 -07:00
5cc8a3ec82
Add back fake us delay.
2020-04-21 14:14:49 -07:00
17d038830d
Use our own flag for board crystal config.
2020-04-21 14:14:30 -07:00
c04e6d6f52
nrf: bleio: parameterize softradio configuration
...
Allow for setting various softradio memory settings as part of a
board in order to support lower-memory configurations. If a
parameter is unspecified then the previously-defined value is used.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 12:29:59 +08:00
3537ad4059
nrf: mpconfigport: support configuration of various sizes
...
Conditionally set variables such as the softdevice RAM size, bootloader
size, and the spi m3 buffer size. This allows ports to adjust these
values to suit their needs.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 12:29:58 +08:00
33720af0c6
nrf: mpconfigport: subtract config size from firmware size
...
The BLE Config area needs to be subtracted from the size of the firmware.
THis is because the firmware is counted by walking backwards from the end
of memory, and the BLE config area is placed lower in memory than the
firmware. Subtracting the BLE config size ensures the internal flash
filesystem doesn't try to use the firmware as storage.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 12:29:57 +08:00
3ed5b87b8f
nrf: add support for nrf52833
...
This adds preliminary support for the nRF52833, which is a variant of
the nRF52840 with half the RAM, half the flash, and fewer peripherals.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 12:29:56 +08:00
4ad1cbeea3
nrf: make rgbmatrix and framebufferio optional
...
Ports can set CIRCUITPY_RGBMATRIX and CIRCUITPY_FRAMEBUFFERIO to 0
in their .mk file in order to prevent these from being built. This
is necessary for resource-constrained devices.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 10:44:21 +08:00
066f486b28
nrf: supervisor: support building without BUSIO
...
Only initialize i2c, spi, and uart if building with BUSIO.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 10:44:20 +08:00
ac9d336f40
nrf: make neopixel support optional
...
Add a conditional around the call to neopixel_write(), allowing us
to build for nrf without neopixel support.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-21 09:56:27 +08:00
bebf27e733
Merge remote-tracking branch 'adafruit/master' into lower_power
...
This isn't perfect and needs a bit more testing.
2020-04-20 18:25:13 -07:00
a4d86b96fd
Merge pull request #2777 from pewpew-game/master
...
Fix RGB/BGR colors in Stage
2020-04-20 15:25:29 -07:00
506f340c7d
STM32: f767: Fixes linker settings.
2020-04-20 19:15:18 +02:00
5fcc6d6286
RGBMatrix: finish renaming from Protomatter
...
This gets all the purely internal references. Some uses of
protomatter/Protomatter/PROTOMATTER remain, as they are references
to symbols in the Protomatter C library itself.
2020-04-17 18:44:07 -05:00
3d6258f63d
Rename Protomatter -> RGBMatrix
...
This is a quick rename, it changes the user-facing names but not the
internal names of things.
2020-04-17 18:43:57 -05:00
a32337718d
Rename _protomatter -> protomatter
...
I originally believed that there would be a wrapper library around it,
like with _pixelbuf; but this proves not to be the case, as there's
too little for the library to do.
2020-04-17 18:43:57 -05:00
7e3d4c61b5
Update TinyUSB and add interrupt hooks.
2020-04-17 14:16:49 -07:00
1a71c8c515
Merge pull request #2735 from hierophect/stm32x7-setup
...
STM32: Add F7 and H7 Support
2020-04-17 13:02:09 -04:00
43022d8294
Add copyrights to pewpew m4 and ugame board.c
2020-04-17 09:50:11 +02:00
9e49fc13f4
startup file crash fix, H7 bin fix
2020-04-16 17:33:48 -04:00
5b0d9bdeb0
Update copyright to bump the CI
2020-04-16 14:21:26 -07:00
b3552efc76
Remove accidental file
2020-04-16 11:28:01 -07:00
61f777c9c6
litex: enable binascii and ujson modules
...
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-16 10:02:08 +08:00
bb527ac9ea
litex: disable minimal build
...
Manually specify available modules and disable any modules
that are currently unsupported on the litex target.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-16 09:26:08 +08:00
db3933429a
litex: add os module
...
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-16 09:26:08 +08:00
6885ffc9af
litex: mphalport: add fake mp_hal_delay_us
...
Add a mp_hal_delay_us, which is required by some of the modules,
that simply calls mp_hal_delay_ms / 1000.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-16 09:26:08 +08:00
f39ca6052e
Fix RGB/BGR colors in Stage
...
This makes the colors used by the stage library compatible with those
used by the displayio library.
2020-04-15 23:41:38 +02:00
00b2e6a1db
Fix korea translation error, minor submodule change
2020-04-15 13:11:14 -04:00
54abfc2e8b
translations-merge
2020-04-15 10:29:05 -04:00
6427994b14
Implement requested changes
2020-04-15 10:22:51 -04:00
b580b34cbf
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-04-14 17:14:44 -07:00
7dfcae6067
Tweaks from jepler
2020-04-14 17:09:48 -07:00
23bced26da
samd: actually disable protomatter timer
...
Just setting the timer handler to NO_INTERRUPT doesn't stop the
interrupt from occurring.
2020-04-14 18:24:58 -05:00
759fdffda5
Update ports/atmel-samd/boards/pyportal_titano/board.c
...
Co-Authored-By: Scott Shawcroft <scott@tannewt.org>
2020-04-14 18:24:58 -05:00
1d8a073c05
nrf: protomatter port
2020-04-14 18:24:58 -05:00
09dc46a984
Add Protomatter and FramebufferDisplay
2020-04-14 18:24:54 -05:00
a51d4f7a45
pycubed: add trailing newline to file
...
POSIX specifies that text files end in a trailing newline
2020-04-14 18:24:54 -05:00
db01f88cc3
enable MICROPY_PY_REVERSE_SPECIAL_METHODS where ulab is enabled
2020-04-13 19:58:52 -05:00
83a55f65a4
Implement cache-based reads
2020-04-13 15:14:38 -04:00
426d2afe28
Fix pin mapping for the H7 Nucleo
2020-04-13 14:36:49 -04:00
6227e63cc5
Merge remote-tracking branch 'upstream/master' into stm32x7-setup
2020-04-13 12:03:56 -04:00
5ac38c95cc
Various requested fixes
2020-04-13 12:03:05 -04:00
cac4fb0318
Merge branch 'master' into nfc_copy
2020-04-09 17:05:11 -05:00
49771b4d7f
Update to v1.3
2020-04-09 14:27:51 -05:00
92a0621e59
Add busio support, cleanup
2020-04-09 13:43:19 -04:00
01941c027b
Fix up STM
...
Enable the Alarm IRQ earlier and correct bit clearing.
2020-04-08 14:41:57 -07:00
d0a25ca9ac
Tweaks based on dhalberts feedback
2020-04-08 10:49:46 -07:00
181ecf4a9b
fixing my goofy CROSS_COMPILE fix
2020-04-07 21:54:46 -07:00
a53a26be70
missed a debug flag
2020-04-07 18:24:53 -07:00
826837186c
adds standard (non-queued) SPI support to QSPI for external flash
2020-04-07 18:17:25 -07:00
6544bf52fb
Enable SNVS interrupt
...
The iMX RT has a separate wake up controller, the GPC, that replaces
the NVIC when asleep. It adds the ability to only wake up on certain
interrupts. It seems that it requires at least one enabled interrupt
in the NVIC to turn on it's wake up circuitry. It doesn't need to
be the same interrupt as the wake up signal. For example, the RTC
in the SNVS can wake us up if a USB interrupt is enabled. Before
then it won't work. So, we enable the SNVS interrupt on start up
so it can wake us up.
2020-04-07 17:15:18 -07:00
aae0ce6bad
Fix autoreload and ticks on IMX RT
2020-04-07 14:16:07 -07:00
a8dfba235c
Fix alarm so that it is correctly set.
2020-04-07 13:07:29 -07:00
c0ba2a839f
Updates based on feedback from jepler
2020-04-06 16:03:31 -07:00
08f369ea96
mimxrt1011: Only re-init SPI when it's actually needed
...
If some crazy code (*cough* FourWire) decides to reconfigure the bus
before every transfer, it might get a bit slow...
2020-04-06 22:10:12 +02:00
e99cf6e441
Rework sleep timing
...
It didn't account for background task time and could end up
sleeping for way longer than it should because the RTC compare time
had already passed.
2020-04-03 18:07:56 -07:00
7e69d30c02
Fix nRF PulseIn
2020-04-03 14:22:56 -07:00
9761672d42
Linker file restructure, TCM and MPU additions
2020-04-03 16:33:18 -04:00
46af4bdd0e
Fix SAMD21 PulseIn
2020-04-02 17:35:52 -07:00
47a5d83267
Implement F7 Nucleo
2020-04-02 11:47:16 -04:00
9845a064ad
ports: fomu: move more functions into ram for stability
...
The SPI flash on current Fomu firmware is slow. Circuitpython runs
XIP from SPI flash, and so execution time can also be slow. Ordinarily
this isn't a problem, however certain operations are time-sensitive.
In particular, USB function needs to be handled quickly in order to
prevent the host from re-enumerating the device.
Place several critical TinyUSB structures into RAM, as well as several
hot functions that are frequently called. This reduces execution time
at the expense of system memory, and greatly improves system stability.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-04-02 11:21:22 +08:00
2f764ded63
merge and docs
2020-04-01 13:52:53 -04:00
a89928c13c
Implement requested changes
2020-04-01 13:02:05 -04:00
77562a2acd
Update the supported ports
2020-03-31 18:27:55 -07:00
75b7f583d2
Update LiteX APIs for new tick
2020-03-31 17:52:23 -07:00
1071924701
Fix thunderpack build
2020-03-31 17:05:37 -07:00
317b96e93a
Fix iMX builds
2020-03-31 17:00:30 -07:00
8fe512c7e9
Merge remote-tracking branch 'adafruit/master' into lower_power
2020-03-31 15:13:58 -07:00
4b063aeb29
Hack up STM32 PulseIn so it builds
2020-03-31 15:12:11 -07:00
f47b964c5f
Merge pull request #2726 from xobs/fomu-circuitpython
...
ports: litex: add port and fomu board
2020-03-31 13:51:09 -07:00
cbe9512691
Merge pull request #2741 from tannewt/fix_packetbuffer_server
...
Fix PacketBuffer server support
2020-03-31 13:39:34 -07:00
c69f7f8657
ports: litex: use dfu.py instead of dfu-suffix.py
...
dfu.py now generates proper dfu suffixes without the nonstandard prefix.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-03-31 13:04:59 +08:00
34ea140783
ports: fomu: build dfu as part of Makefile
...
Now that we have a replacement for `dfu-suffix`, construct a dfu
image rather than a UF2 image.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-03-31 11:42:55 +08:00
065441e58c
ports: litex: enable itcm region for fomu
...
This adds a new command line flag -DFOMU to indicate we're building
for a Fomu board.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-03-31 09:40:38 +08:00
786e79ebc9
ports: litex: add port and fomu board
...
This adds support for Litex, along with support for the Fomu FPGA board.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-03-31 09:40:38 +08:00
e8cffcf978
Merge pull request #2740 from arturo182/mimxrt10xx_neopixel
...
mimxrt10xx: Fix neopixel_write
2020-03-30 17:49:14 -07:00
13022be299
mimxrt10xx: Fix neopixel_write
2020-03-31 01:05:03 +02:00
7cfa8e1a68
board_vina_m0:pins.c: PGM_LED is on PA28 not PA15.
2020-03-29 18:59:00 -04:00
e2be069686
Support cached internal flash on the H743
2020-03-28 18:30:46 -04:00
54e8c63b4f
Merge pull request #2730 from tannewt/fix_fourwire_phase_polarity
...
Add polarity and phase to FourWire.
2020-03-28 07:28:37 -05:00
a4a458943d
Correct MIMXRT sdk version
2020-03-27 15:40:17 -07:00
798118b74f
Update board.c's to remove remaining tick.h
2020-03-27 14:52:35 -07:00
e4c4a4a3de
Swap to committed dependencies
2020-03-27 14:39:59 -07:00
b043384949
Update built in display init
2020-03-27 14:35:29 -07:00
7995bcac40
Flash additions
2020-03-27 14:15:33 -04:00
7fa38e8725
Update board name to bdmicro_vina_m0 to eliminate hyphens.
2020-03-27 13:37:59 -04:00
14a1e5756e
Merge branch 'master' of https://github.com/adafruit/circuitpython
2020-03-26 20:28:54 -04:00
2ae9edcbff
Add new board BDMICRO 'Vina M0'.
...
ports/atmel-samd/boards/bdmicro_vina_m0/board.c
ports/atmel-samd/boards/bdmicro_vina_m0/mpconfigboard.h
ports/atmel-samd/boards/bdmicro_vina_m0/mpconfigboard.mk
ports/atmel-samd/boards/bdmicro_vina_m0/board.c
This board includes the newly added MX25L51245G 64MB SPI flash chip
for the CircuitPython file system. Also included is the PCF2129T/2,518
high accuracy, battery backed, RTC. Also includes an independent USB
HOST connector in addition to USB DEVICE making it easy to connect USB
peripherals. Designed mainly as a general purpose module to piggy back
onto application-specific boards, it can also run low power standalone
in harsh environments for data logging and other control applications
using an appropriate enclosure.
Has been extensively tested with CircuitPython and works well.
2020-03-26 20:15:54 -04:00
348df4be2b
Merge remote-tracking branch 'upstream/master' into stm32x7-setup
2020-03-26 18:16:11 -04:00
c4db8b87e2
Add F7 and H7 Support to the STM32 port
...
Restructures the STM port of Circuitpython to be more generic about the STM32 chip lines to support
the F7 and H7 series of chips. Adds the new Packages directory to organize different chip layouts
between lines. Makes general changes to the Makefile to condense board-level flags to the minimum
and support the new chip series. Adds the new chip line to the Peripherals directory, along with
new python tools used to generate peripheral text automatically in the tools/ directory.
2020-03-26 18:01:17 -04:00
aec3b2419b
Merge pull request #2733 from oshwabadge2020/change_backlight
...
Add backlight polarity flag to Display
2020-03-26 14:00:47 -07:00
Scott Shawcroft
Daniel Pollard
Sean Cross
Lucian Copeland
Scott Shawcroft
DavePutz
warriorofwire
Max Holliday
Dan Halbert
Jeff Epler
Dan Halbert
Yihui Xiong
JoeBakalor
TG-Techie
Mark Olsson
Radomir Dopieralski
Jeff Epler
Sabas
sabas1080
arturo182
Brian Dean
Jeff Epler