* Enable dcache for OCRAM where the VM heap lives.
* Add CIRCUITPY_SWO_TRACE for pushing program counters out over the
SWO pin via the ITM module in the CPU. Exempt some functions from
instrumentation to reduce traffic and allow inlining.
* Place more functions in ITCM to handle errors using code in RAM-only
and speed up CP.
* Use SET and CLEAR registers for digitalio. The SDK does read, mask
and write.
* Switch to 2MiB reserved for CircuitPython code. Up from 1MiB.
* Run USB interrupts during flash erase and write.
* Allow storage writes from CP if the USB drive is disabled.
* Get perf bench tests running on CircuitPython and increase timeouts
so it works when instrumentation is active.
This 2-in-1 PR started with the goal of support the Bangle.js 2
smartwatch with *no USB*.
* Adds "secure" DFU build support with a committed private key.
* Adds 3-bit color support with one dummy bit for the JDI memory display
* Allows nrf boards to have a board_background_task() run in RUN_BACKGROUND_TASK.
This is needed because the Bangle.js 2 uses the watchdog to reset.
* Renamed port_background_task() to port_background_tick() to indicate it
runs on tick, not RUN_BACKGROUND_TASK.
* Marks serial connected when the display terminal is inited. This means
that safe mode messages show up on the display.
ACep, 7-color epaper displays also pack 3 bits in 4. So, I added that
support as well.
* Adds 3-bit ACeP color support for 7-color e-paper displays. (Not
watch related but similar due to color depth.)
* Allows a refresh sequence instead of a single int command. The 7" ACeP
display requires a data byte for refresh.
* Adds optional delay after resetting the display. The ACeP displays
need this. (Probably to load LUTs from flash.)
* Adds a cleaning phase for ACeP displays before the real refresh.
For both:
* Add dither support to Palette.
* Palette no longer converts colors when set. Instead, it caches
converted colors at each index.
* ColorConverter now caches the last converted color. It should make
conversions faster for repeated colors (not dithering.)
* Tweak scroll area position so last line is complete and top is
under the title bar.
* Pick Blinka size based on the font to minimize unused space in
title bar. Related to #2791
* Update the title bar after terminal is started. Fixes#6078Fixes#6668
This adds support for CIRCUITPY_WIFI_SSID and CIRCUITPY_WIFI_PASSWORD
in `/.env`. When both are defined, CircuitPython will attempt to
connect to the network even when user code isn't running. If the
user code attempts to a network with the same SSID, it will return
immediately. Connecting to another SSID will disconnect from the
auto-connected network. If the user code initiates the connection,
then it will be shutdown after user code exits. (Should match <8
behavior.)
This PR also reworks the default displayio terminal. It now supports
a title bar TileGrid in addition to the (newly renamed) scroll area.
The default title bar is the top row of the display and is positioned
to the right of the Blinka logo when it is enabled. The scroll area
is now below the Blinka logo.
The Wi-Fi auto-connect code now uses the title bar to show its
state including the IP address when connected. It does this through
the "standard" OSC control sequence `ESC ] 0 ; <s> ESC \` where <s>
is the title bar string. This is commonly supported by terminals
so it should work over USB and UART as well.
Related to #6174
This targets the 64-bit CPU Raspberry Pis. The BCM2711 on the Pi 4
and the BCM2837 on the Pi 3 and Zero 2W. There are 64-bit fixes
outside of the ports directory for it.
There are a couple other cleanups that were incidental:
* Use const mcu_pin_obj_t instead of omitting the const. The structs
themselves are const because they are in ROM.
* Use PTR <-> OBJ conversions in more places. They were found when
mp_obj_t was set to an integer type rather than pointer.
* Optimize submodule checkout because the Pi submodules are heavy
and unnecessary for the vast majority of builds.
Fixes#4314
Call `supervisor.disable_ble_workflow()` and the BLE workflow will
be disabled until the chip is reset.
This also includes a couple fixes:
1. Terminals can now be deinit by setting the tilegrid to NULL. This
prevents using the tilegrid before display is init.
2. Fix BLE serial send amount when sending more than a single packet.
Fixes#5049
Since we made the decision to allow translations which do not have coverage in
the terminal font, these routinely occur and are expected. The message is
unhelpful and due to their voume make it harder to find relevant information
particularly in github actions results.
It was intended that the `f.load_glyphs` line was fast and did most of
the work. However, it actually didn't, because it's necessary to pass
in a code point by number, not by string.
Additionally, a little light layer violation is needed to make the check
for missing characters fast. This used to be less important, as no
fonts had missing characters. However, it would take an appreciable
length of time on the Korean translation when failing to find hundreds
of different code points.
Testing performed: built
build-circuitplayground_express_displayio/autogen_display_resources.c with ko
translation before and after change. verified the file content was identical.
Time went from about 7s on my machine to way under 1 second.
This also improves Palette so it stores the original RGB888 colors.
Lastly, it adds I2CDisplay as a display bus to talk over I2C. Particularly
useful for the SSD1306.
Fixes#1828. Fixes#1956
This fixes the bug that bitmap changes do not cause screen updates
and optimizes the refresh when the bitmap is simply shown on the
screen. If the bitmap is used in tiles, then changing it will
cause all TileGrids using it to do a full refresh.
Fixes#1981
Instead of iterating over all the glyphs and calculating the maximum
width and height, use the FONTBOUNDINGBOX to determine the size of a
tile for terminalio.
This works better with fonts such as generated by FontForge, that don't
include the empty space in the glyph bitmap itself. It also lets the
font author specify vertical spacing they want.
I only tested this with the default font and with one I generated with
FontForge.
Different operations to the display tree have different costs. Be
aware of these costs when optimizing your code.
* Changing tiles indices in a TileGrid will update an area
covering them all.
* Changing a palette will refresh every object that references it.
* Moving a TileGrid will update both where it was and where it moved to.
* Adding something to a Group will refresh each individual area it
covers.
* Removing things from a Group will refresh one area that covers all
previous locations. (Not separate areas like add.)
* Setting a new top level Group will refresh the entire display.
Only TileGrid moves are optimized for overlap. All other overlaps
cause sending of duplicate pixels.
This also adds flip_x, flip_y and transpose_xy to TileGrid. They
change the direction of the pixels but not the location.
Fixes#1169. Fixes#1705. Fixes#1923.
This changes the displayio pixel computation from per-pixel to
per-area. This is precursor work to updating portions of the screen
(#1169). It should provide mild speedups because bounds checks are
done once per area rather than once per pixel. Filling by area also
allows TileGrid to maintain a row-associative fill pattern even when
the display's refresh is orthogonal to it.
This changes a number of things in displayio:
* Introduces BuiltinFont and Glyph so the built in font can be used by libraries. For boards with
a font it is available as board.TERMINAL_FONT. Fixes#1172
* Remove _load_row from Bitmap in favor of bitmap[] access. Index can be x/y tuple or overall index. Fixes#1191
* Add width and height properties to Bitmap.
* Add insert and [] access to Group. Fixes#1518
* Add index param to pop on Group.
* Terminal no longer takes unicode character info. It takes a BuiltinFont instead.
* Fix Terminal's handling of [###D vt100 commands used when up arrowing into repl history.
* Add x and y positions to Group plus scale as well.
* Add bitmap accessor for BuiltinFont
Scott Shawcroft
Dan Halbert
Timon
James Carr
Jeff Epler
microDev
foamyguy
Diego Elio Pettenò
Jeff Epler
Radomir Dopieralski