Previously the end of the heap was the start (lowest address) of the stack.
With the changes in this commit these addresses are now independent,
allowing a board to place the heap and stack in separate locations.
With this the user can select multiple logical units to expose over USB MSC
at once, eg: pyb.usb_mode('VCP+MSC', msc=(pyb.Flash(), pyb.SDCard())). The
default behaviour is the original behaviour of just one unit at a time.
Eventually these responses could be filled in by a function to make their
contents dynamic, depending on the attached logical units. But for now
they are fixed, and this patch fixes the MODE SENSE(6) responses so it is
the correct length with the correct header.
SCSI can support multiple logical units over the one interface (in this
case over USBD MSC) and here the MSC code is reworked to support this
feature. At this point only one LU is used and the behaviour is mostly
unchanged from before, except the INQUIRY result is different (it will
report "Flash" for both flash and SD card).
Previously, when linking qstr objects in native code for ARM Thumb, the
index into the machine code was being incremented by 4, not 8. It should
be 8 to account for the size of the two machine instructions movw and movt.
This patch makes sure the index into the machine code is incremented by the
correct amount for all variations of qstr linking.
See issue #4829.
To use it a board should define MICROPY_PY_USSL=1 and MICROPY_SSL_MBEDTLS=1
at the Makefile level. With the provided configuration it adds about 64k
to the build.
Setting MICROPY_PY_USSL and MICROPY_SSL_MBEDTLS at the Makefile-level will
now build mbedTLS from source and include it in the build, with the ussl
module using this TLS library. Extra settings like MBEDTLS_CONFIG_FILE may
need to be provided by a given port.
If a port wants to use its own mbedTLS library then it should not set
MICROPY_SSL_MBEDTLS at the Makefile-level but rather set it at the C level,
and provide the library as part of the build in its own way (see eg esp32
port).
Instead of converting to a small-int at runtime this can be done at compile
time, then we only have a simple comparison during runtime. This reduces
code size on some ports (e.g -4 on qemu-arm, -52 on unix nanbox), and for
others at least doesn't increase code size.
Fixes errors in the tool when 1) linking qstrs in native ARM-M code; 2)
freezing multiple files some of which use native code and some which don't.
Fixes issue #4829.
It doesn't work to tie the polling of an underlying NIC driver (eg to check
the NIC for pending Ethernet frames) with its associated lwIP netif. This
is because most NICs are implemented with IRQs and don't need polling,
because there can be multiple lwIP netif's per NIC driver, and because it
restricts the use of the netif->state variable. Instead the NIC should
have its own specific way of processing incoming Ethernet frame.
This patch removes this generic NIC polling feature, and for the only
driver that uses it (Wiznet5k) replaces it with an explicit call to the
poll function (which could eventually be improved by using a proper
external interrupt).
This adds support for SD cards using the ESP32's built-in hardware SD/MMC
host controller, over either the SDIO bus or SPI. The class is available
as machine.SDCard and using it can be as simple as:
uos.mount(machine.SDCard(), '/sd')
If the board-pin name is left empty then only the cpu-pin name is used, eg
",PA0". If the board-pin name starts with a hyphen then it's available as
a C definition but not in the firmware, eg "-X1,PA0".
The patch solves the problem where multiple Timer objects (e.g. multiple
Timer(0) instances) could initialise multiple handles to the same internal
timer. The list of timers is now maintained not for "active" timers (where
init is called), but for all timers created. The timers are only removed
from the list of timers on soft-reset (machine_timer_deinit_all).
Fixes#4078.
The board config option MICROPY_HW_USB_ENABLE_CDC2 is now changed to
MICROPY_HW_USB_CDC_NUM, and the latter should be defined to the maximum
number of CDC interfaces to support (defaults to 1).
mpy-cross uses MICROPY_DYNAMIC_COMPILER and MICROPY_EMIT_NATIVE but does
not actually need to execute native functions, and does not need
mp_fun_table. This commit makes it so mp_fun_table and all its entries are
not built when MICROPY_DYNAMIC_COMPILER is enabled, significantly reducing
the size of the mpy-cross executable and allowing it to be built on more
machines/OS's.
In d5f0c87bb9 this call to tcp_poll() was
added to put a timeout on closing TCP sockets. But after calling
tcp_close() the PCB may be freed and therefore invalid, so tcp_poll() can
not be used at that point. As a fix this commit calls tcp_poll() before
closing the TCP PCB. If the PCB is subsequently closed and freed by
tcp_close() or tcp_abort() then the PCB will not be on any active list and
the callback will not be executed, which is the desired behaviour (the
_lwip_tcp_close_poll() callback only needs to be called if the PCB remains
active for longer than the timeout).
